Summary
A holder for quadcopter batteries, the size of the inner compartment is 25x9x44. In the picture it says 400 mah, I changed it in the design to: “batteries”, so if you have different batteries it’s not the wrong value.
Print Settings
Printer:
TronXY X1
Rafts:
Doesn’t Matter
Supports:
Yes
Resolution:
0.2
Infill:
20
Notes:
the print orientations are correct, you need the print: “Quad_battery_holder_Thingiverse_1” with supports.
Author: Thingiverse
-
Quadcopter battery storage 3D Print Model
-
Battlestar Valkyrie 3D Print Model
Summary
Battlestar Valkyrie model pulled from Sins of a Solar Empire mod Fall of Kobol (http://www.moddb.com/mods/fall-of-kobol).
Still working on getting it optimized for printing. -
Tribute to Tiffanys pen holder 3D Print Model
Summary
This was created as a gag gift for some people in the office. It was supposed to resemble the $1000 Tiffany’s sterling silver pen holder.
Best results can be achieved by using primer filler and wet sanding a few times, then painting the model with sterling silver spray paint
The inside of the “can” was painted with Rust-Oleum 284678, Gloss Light Turquoise
Print Settings
Printer:
D-Bot / Anet A8
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
.2mm
Infill:
Doesn’t matter
Notes:
Might want to print the first layer slow to get the best resolution on the text. -
Xhover Win5L SMA + Immortal T Holder 3D Print Model
Summary
Designed a SMA + Immortal T mount for the new Xhover Win5L frame. Same basic design as the one for the Win5, but with the posts adjusted further in. Needs to be printed in TPU in order to get the Immortal T in the hooks.
Print Settings
Printer:
Wanhao Duplicator i3 Plus
Rafts:
Doesn’t Matter
Supports:
Yes
Notes:
Print in TPU -
Konahrik Dragon Priest Mask SLICED 3D Print Model
Summary
I really liked the mask but I only have a 8x8x8 build space so I sliced this guy up in mesh mixer for those in a similar boat. This should work on many more printers now. Print edge down on glass bed with auto supports and it should come out perfect after you glue the edges.
Print Settings
Printer Brand:
TEVO
Printer:
Tornado
Rafts:
Doesn’t Matter
Supports:
Yes
Infill:
30
Notes:
Use brim if printing fast so print doesnt come off bed.
GO TO JTM’S PAGE FOR TUSKS -
Uncle Grandpa Time Machine Watch 3D Print Model
Summary
My son is a fan of the Cartoon Network show Uncle Grandpa. In s03e03 Back to the Library, Uncle Grandpa uses a time machine watch to travel through time. My son wanted one so I made this model and printed him off one. It’s modeled to his size, so scale to what will fit you.
Print Settings
Rafts:
No
Supports:
NoPost-Printing
You’ll need to add a strap to this. Given the size I printed mine at, it requires something custom.
It also requires some blue paint for the recessed triangle and “buttons”. -
full register and buss 3D Print Model
Summary
this is the full register and buss, each register of the processor will use this component.
http://www.imm.org/Reports/rep046.pdf
the scad file also contains the other components that have been uploaded previously.
t.
Eventually i intend to parameterize the file and make it animatable but my current skill level with open scad is rudimentary at best. -
P Body Seat Latch 3D Print Model
Summary
Rear seat release handle for Dodge Shadow and Dodge Lancer cars.
Please abide by the license agreement. -
Pièce pour Hyper Master Mind 3D Print Model
Summary
Entretoise moyenne pour pion du jeu Hyper Master Mind (Mean Spacer for Master mind game pawn). -
Ohrenspritzenträger / ear syringe holder 3D Print Model
Summary
Ein Halter für ein Ohrenspritzenball, bei dem die restliche Feuchtigkeit abtropfen kann.
A holder for an ear syringe ball, where the remaining moisture can drip off.
Print Settings
Printer:
CTC
Rafts:
No
Supports:
No
Resolution:
0,1 mm
Infill:
15 %
Notes:
PLA -
lock with wire clip for Creality Ender 2 wire chain 3D Print Model
Summary
I remixed the lock of the Ender Cable Chain by ninne (https://www.thingiverse.com/thing:2498801) with the clamp of the bowden wire clips by Evanrude (https://www.thingiverse.com/thing:2328449) to attach the hot bed cable to the chain. It prevents the hot bed calbe from scrubbing the chain and the power cable. -
open cable chain 3D Print Model
Summary
This is a 10 x 15 open style cable chain with a radius of 18 degrees for best performance print in nylon. here is a video showing the assembly of the links.
IF YOU LIKE THE DESIGN AND WILL LIKE TO SEE MORE STUFF LIKE THIS PLEASE LEAVE A COMMENT BELOW, ALSO DON’T HESITATE TO CONTRIBUTE WITH A TIP
Print Settings
Printer:
ft-5, flash forge creator pro
Rafts:
No
Supports:
Yes
Resolution:
.1
Infill:
50%
Notes:
This has very high tolerance so make sure your printer is calibrate and has a very good cooling fan i have printed this an test so i know it work as it should
How I Designed This -
Improved corgi 4x leash hook 3D Print Model
Summary
First I’ve found and printed this hook: https://www.thingiverse.com/thing:285782
The PLA version was able to withstand my puppy pulling on the leash for about 3 days, then the hooks started breaking off. I’ve made another one in PETG, that one successfully served its purpose for about 2 weeks. Then I realized that there’s a weak spot where the hooks connect to the plate. So I decided to design my own. Basically this is the same overall shape and size, but the hooks and the plate are thicker and I’ve filleted the joint between the hooks and the plate. Also this one has twice as many corgis 🙂
Print Settings
Printer Brand:
Wanhao
Printer:
Wanhao Duplicator i3 Plus
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
0.2 mm
Infill:
30-50%
Notes:
For better strength print in PETG -
Oral-B Tooth Brush Cover and Wall Mount 3D Print Model
Summary
::::: Caution :::::: This item has a few very thin slice areas. Must be printed with no more than a .25mm height or thickness. Any thicker it will not print the hinges.
Print and then fold up the top and dab a bit of supper glue to firmly connect the top part of cover. The hinge will last a long time if the cover top is just snapped up and toothbrush removed. Flipping the cover up and all the way over will soon break it. Should not need blow drier for heat on the hinge. The other mount piece would be for mounting on a wall. Mount it and then use double stick tape on the cover.
Hope you enjoy. Happy printing !! 🙂 -
Jewelry hanging arm hook 3D Print Model
Summary
這是一個首飾掛臂鈎，這個小零件的設計是把有外包裝的首飾能懸掛在5mm厚的板上。物件尺寸：029mm(w) x 35mm(h) x 45mm(d)。
This is a jewelry hanging arm hook, this small part is designed to be overhang jewelry hanging on the 5mm thick board.Object size: 29mm (w) x 35mm (h) x 45mm (d). -
TEVO Tornado Ultrabase Upgrade Remix with cable strain relief 3D Print Model
Summary
Clamps to attach Anycubic Ultrabase to the Tevo Tornado.
Added cable strain relief to the rear left part.
Remixed this https://www.thingiverse.com/thing:2782720 and this https://www.thingiverse.com/thing:2748197 things. -
Jewelry display#2 3D Print Model
Summary
這是我第二個設計的首飾展示架，它的特點在於可以把最上的零件拆下及更換其他不同形狀的零件，而在弧形的上方可以加上絨毛布防止飾品滑下，在前下方的凹陷位位置是設計來放置貨品介紹的牌。物件尺寸：50mm(w) x 80mm(h) x 60mm(d), 厚度是 2mm。
This is my second design jewelry display stand, which is characterized by the top parts can be removed and replaced with other parts of different shapes, and in the top of the arc can be added fluff cloth to prevent the jewelry slide down in front of the bottom The recessed position is the card that is designed to place the item introduction.Object size: 50mm (w) x 80mm (h) x 60mm (d), the thickness is 2mm. -
Parametric Sine Design V1 3D Print Model
Summary
Diseño paramétrico realizado con Rhinoceros5 + grashopper -
ZAV ReArm mount 3D Print Model
Summary
ZAV ReArm board mount
Print Settings
Printer:
ZAV
Rafts:
No
Supports:
No
Resolution:
0.2
Infill:
30 -
Snow Stake Medium 3D Print Model
Summary
A two part medium sized snow stake. To assemble put the smaller piece (the one with the numbers) into the hole in the larger piece. It will fit for a accurate measurement. -
Small Snow Stake 3D Print Model
Summary
A two part small sized snow stake. To assemble put the smaller piece (the one with the numbers) into the hole in the larger piece. It will fit for a accurate measurement. -
Ⅎɐɔʇoɹᴉo 3D Print Model
Summary
No special settings required!
Print Settings
Printer Brand:
Creality
Printer:
CR-10S
Rafts:
Doesn’t Matter
Supports:
Doesn’t Matter
Resolution:
.2
Infill:
15 -
GoPro Session 5 protector cap 3D Print Model
Summary
Gopro Session Cap to hold your camera in place. Print in TPU. This was designed for the seesion and has a front and back lip that locks the camera in place. Does not show in superview. I have never had an eject with this cap. -
Lucky Clover Soap Box and Coaster 3D Print Model
Summary
Lucky Clover Soap Box and Coaster
Print Settings
Printer:
CR-8
Rafts:
Yes
Supports:
No
Resolution:
0.2
Infill:
10Post-Printing
How I Designed This
123D Design
-
Rounding Hill for Elementary School Students 3D Print Model
Summary
This is a tool to help students achieve a concrete understanding on how to round numbers.
Print Settings
Printer Brand:
FlashForge
Printer:
Finder
Rafts:
Yes
Supports:
Doesn’t Matter
Resolution:
Default
Infill:
Default
Notes:
I used a raft to help with the curling issues that I had been having.Standards
CCSS
Overview and Background
Overview
Students will learn how to round a number.
Lesson Plan and Activity
Lesson Plan
Teacher will show students how to round a number, such as 12 on chart paper. Students will copy the anchor chart in their Student Journals.
Step 1:
Teacher will show students to find their number and underline it. If rounding to the tens place, that would be the 1.
Step 2:
Teacher will show students to “look next door” to the right, which will show the underlined number what to either round up or round down. The number in the example is 2.
Step 3:
Teacher will show students that if the number on the right is 4 or less to “let it rest” and keep the underlined number the same.
Step 4:
Teacher will show students that if the number is 5 or greater, to add 1 more to the underlined number.
Step 5:
Teacher will make sure students understand that all numbers after the underlined number will become a Zero, and that numbers before the underline will not change.
Students will take a look at the “Rounding Hill”, which will show the concrete example of rounding. Students will imagine a toy car stopping on the numbers. If the car stops on or before the 4, the toy car will be pulled by gravity back down to the 0, and will let the underlined number rest. If the toy car stops on or after the 5, gravity will pull the car down to the right side, signifying that they will add 1 more to the underlined number.Anchor Chart
Materials Needed
Materials Needed
Student Journals, Pencils, Chart Paper, Markers, Rounding Manipulatives.
Skills Learned
Rounding
Number Sense
Math
Duration of Lesson
15-30 Minutes
Preparation
Preparation
Gather materials, print out several Rounding Manipulatives. -
Caliburn MuzzleVF1 Friction Fit 3D Print Model
Summary
This is a quick modification to Slug’s Caliburn MuzzleVF1 file, which is an extended muzzle break essentially. It is a friction fit onto the aluminum barrel and doesn’t require screws to be attached. I found that the muzzle would be off-axis from the barrel because of the single screw point and I wanted it to work for when I eventually swap out for a longer barrel. -
1515 extrusion cap/foot 3D Print Model
Summary
Protective cap/foot for 1515 extrusion.
Needs a 6mm M3 bolt and nut to secure it in place. -
e3d v6 30mm layer fan 3D Print Model
Summary
30mm layer cooling fan for the E3d v6 hotend.
Designed to fit the monoprice mini but could be used on any printer with the same style mount.
Print Settings
Printer:
m200
Rafts:
No
Supports:
Yes
Resolution:
0.175
Infill:
30+
Notes:
You will need a m3x35mm Alan key head bolt and nut.
only test fitted to this mount.https://www.thingiverse.com/thing:1621387 -
Glass Apple 3D Print Model
Summary
This is a ready to print glass apple designed using SelfCAD software.
To design yours visit https://www.selfcad.com
Print Settings
Printer Brand:
Afinia
Printer:
AFINIA H480
Rafts:
No
Supports:
Doesn’t MatterPost-Printing
Make sure the model is cool before using it
How I Designed ThisStandards
CCSS
Overview and Background
Visit https://www.selfcad.com to sign up for a free account and then launched the editor and you willl be ready to design the model.
Lesson Plan and Activity
Visit https://www.selfcad.com to sign up for a free account and then launched the editor and you willl be ready to design the model
Materials Needed
-Steel
SelfCAD
3D printer
Skills Learned
3d modeling
3d designing
3d design
arts
Duration of Lesson
10 minutes
Preparation
Check this tutorial https://www.instructables.com/id/Glass-Apple-Created-in-SelfCAD/
Rubric and AssessmentReferences
https://www.youtube.com/watch?v=G1pq7EdQzAshttps://www.instructables.com/id/Glass-Apple-Created-in-SelfCAD/https://www.blog.selfcad.com/ -
858D Syringe Holder 3D Print Model
Summary
Here a Syringe Hoder for the 858 HotAir Station
Holds up to three 22cc (19mm Diameter) Syringes
Print Settings
Printer:
Hypercube
Rafts:
No
Supports:
No
Resolution:
0.2mm
Infill:
20%
Notes:
3 Top/Bottom Layer , 2 Perimeter
Printed with
“Das Filament” PETG
220/60°C @ 50mm/s -
Box corner protect 3D Print Model
Summary
Pour la protection Protection des angles de la caisse de l’imprimante ou autre.
Print Settings
Printer:
Anet
Rafts:
Doesn’t Matter
Supports:
Doesn’t Matter -
Coke Bottle Male Connector 3D Print Model
Summary
Plastic bottle male connector for combining various fittings and plugs together.
Download my fitting and combine various parts together to create all types of items.https://www.thingiverse.com/thing:1132995https://www.thingiverse.com/thing:2799255https://www.thingiverse.com/thing:2793776https://www.thingiverse.com/thing:2792632https://www.thingiverse.com/thing:2792719https://www.thingiverse.com/thing:2797468 -
Bottle Stand, Pool Table 3D Print Model
Summary
Bottle stand, Light pole stand, Floating pool table support.
Options are endless, your imagination is your stumbling block 🙂
Fill the bottles with water and color with food coloring.
Shine a light into the lower centre hole and light up the others……
Connect a garden hose to the centre connection…..
Download some of my other connections to make various combinations of ……https://www.thingiverse.com/thing:1132995https://www.thingiverse.com/thing:2799255https://www.thingiverse.com/thing:2793776https://www.thingiverse.com/thing:2792632https://www.thingiverse.com/thing:2792719https://www.thingiverse.com/thing:2797468 -
MoozHoldDowns 3D Print Model
Summary
HUGE Print!
Worth it though.
These are hold downs that will allow you to attach the carving bed without removing the print bed.
I had to print them 1 at a time. I had a problem with the print lifting at the back left corner. The smaller object is the one for the back left corner where the heater attaches to the bed.
If someone sees a better please let me know.
Cheers! and 73’sOverview and Background
This is for fellow Educator Moozers
These hold downs will make it easier for you to use the carving attachment, with less risk of breaking the standard bed.
Lesson Plan and Activity
Useful Engineering
Have students discuss how they would attach the carving bed without removing the print bed.
When they have come close to useful design, present these hold downs and have them modify them to fit their styles.
Use Tinkercad if needed. -
Lumber Jack-Knife 3D Print Model
Summary
This started out as an “Artistic” 3D model, but I thought I would try and make it printable and functional as such.
Print Settings
Printer Brand:
Prusa
Printer:
Prusa Clone
Rafts:
No
Supports:
No
Resolution:
0.1
Infill:
N/A
Notes:
Use the orientations shown.
Post-Printing
Assembly:
Print 4 Cogs, 2 Guides, 2 Braces, 4 20mm Pins, 2 12mm pins, and 1 of everything else.
Refer to the exploded view here: https://youtu.be/mUq02HKfeVU
The chain is in two print-in-place pieces, gently break each link free if needed and work them until they move freely. Assemble the two different lengths by clipping them together with the hooks facing out.
Assemble the front of the blade using a piece of 1.75mm filament as a pin between the guide parts. Press 12mm pins in both sides, make sure they are aligned properly and firmly snap them together.
Slip the cover piece onto the blade (it has a subtle top and bottom) and mount the blade into the top case with two 20mm pins.
Position the bottom case and snap on the cover and handle. Affix the handle with another pair of 20mm pins.
The pins can be a bit finicky, you can use M4 hardware instead.
About:
I was playing around with the Fusion 360 renderer and ended up with the image below. I thought I would see if I could make a printable version. Note the teeth are not on the chain in the included STL files, still having some issues getting them to work out right. -
Mini Master Spool 3D Print Model
Summary
WARNING, Thing is being test printed right now, thus no files. Print at your own risk, I will update this posting if the half’s work properly.
I have an MP select Mini V2, the build volume on these guys is pretty tiny. 120,120,120 (mm) So I wanted a spool that I could print on that printer.
Enter Mini Master Spool, modeled after RichRap’s awesome Master Spool design. This one does not have all the bells and whistles of his as of yet. I will update the spool to provide such features.
This spool may work for sample filaments or just bits of filament you have laying around. its a little smaller than the 250gram .5kilo spools, i cant remember what one this is. the Bottom printed portion is sitting on a injected mini spool for reference.
Print Settings
Printer:
MP Select Mini V2
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
0.30625
Infill:
20% -
Cooling Tower Desert Terrain 3D Print Model
Summary
This is a cooling tower for on top of Desert Terrain Buildings (40k, 28mm scale)
If you look up desert style buildings, many of them have an old but effective way to cool the buildings. They have these towers on top that let all the hot air rise and bleed out leaving cool air in the building.
This is shown with a bunker design I made, but it can go on top of any building or just on top of a mound. -
Dyson attachment 3D Print Model
Summary
This is a attachment that should fit and click in any DC model from Dyson -
Palette+ sensor holder for Wanhao Duplicator 6 3D Print Model
Summary
Holder for the Palette+ filament sensor. Can be screwed on to the backside of the D6 printer. Use the longer screw that came with your printer.
Print both parts an glue them together. I used CA for this job.
Print Settings
Printer Brand:
Wanhao
Printer:
Duplicator 6
Rafts:
No
Supports:
No
Resolution:
0.15
Infill:
45%
Notes:
Used PLA for printing. -
JGAurora A3S Nozzle Cooling Fan 3D Print Model
Summary
Stock Nozzle fan for the JGAurora A3S printer. -
Ruger 10/22 10rd magazine coupler 3D Print Model
Summary
Simple jig which centers the magazines. Use hot glue to weld them together for a non-permanent tack. really for the US states which limit no more than 10 rounds. -
1/4 inch air hose clip 3D Print Model
Summary
holds air hose to reel, use pop rivits in the holes to attach -
plarail for 999. 3D Print Model
Summary
plarail for galaxy express 999.
[Japanese]
銀河鉄道９９９のレールの端っこの部分を再現するためのレールです。 -
Delta 4 Heavy 3D Print Model
Summary
This is a model of the Delta 4 Heavy that I made. Stands almost a foot tall. The model will stand on its own once put together, but I also made a simulated launch pad with mounts to help keep it steady. The second stage easily slides out and is really only held in place by gravity.
I did a little spray paint job on the model just for kicks!
The model does require a little bit of supports. Print vertically, which ever end does not matter. I printed mine with engines and nose cone up.I printed mine using
0.2mm layer height
20% infill
But I think this model will do just fine with a thicker layer height or less infill
The mounts on the launch pad are a bit fragile and break easily, so be careful once printed.
Assembly instructions –
1) Print 3 engine sections, 2 booster tops, 1 core top, 1 second stage, and 4 longerons.
2) The engines should fit snug to the core and booster tops. I did not have to use any glue
3) Lay the boosters and core together on a flat surface. GLUE or WELD the longerons to the model. They do not clip on, so additional adhesive is required.
4) As mentioned above, the model should stand on its own from here (including the 2nd stage). But you can print off the launch pad for added stability
Print Settings
Printer Brand:
Wanhao
Printer:
Wanhao Duplicator i3 Plus
Rafts:
Doesn’t Matter
Supports:
Yes -
Fortnite Bolt-Sniper 3D Print Model
Summary
Basic sniper from fortnite. -
Turny Handle Thing 3D Print Model
Summary
I honestly have no idea what this should be called. I know it’s been done before and I know it’s nothing new. I just wanted to finally make one….whatever it is. Plus it’s pretty satisfying once you make it a put it together and turn it. Works great with PETG or a somewhat flexible filament because it all snaps in place. Also you need to print two sliders, not one. Make sure to put the sliders in their tracks BEFORE you attach the handle to the sliders, otherwise you won’t be able to put it together. It’s not perfect and it’s not beautiful but it’s cool and I like it. So if you like it, then go and print it too I guess.
Print Settings
Supports:
No -
Spike Lugnut Semi Wheel 3D Print Model
Summary
Spike Semi Wheel filament spool cover. I have not printed this item yet, waiting on some silver filament.
Dimensions:
Diameter Total= 7″
Spool insert= 2.35 OD -
H7 LED bulb adapter 3D Print Model
Summary
A simple adapter to get aftermarket H7 LED bulbs to actually lock into their sockets.
Print at 100% infill.
You’ll probably have to whittle the little wings down a bit – this is intentional to ensure a snug fit. -
spool holder 3D Print Model
Summary
.
Print Settings
Printer:
anet a 8
Supports:
Yes
Resolution:
0.15
Infill:
30%Post-Printing
bearing 22mm out 8mm in -
CAD functions explaining 3D Print Model
Summary
This model easly explains the basic functions that can be used in inventor 2018, basicly any CAD software (name functions may be different). this can be very useful for someone who wants to start learning with CAD software.
Print Settings
Printer:
Anet A8
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
0.2 or lower
Infill:
10
Notes:
if ur having trouble with the “revolve” part, then print it with support -
Sunglasses Car Sun Visor Clip – Remix 3D Print Model
Summary
Added a “butée” (french word) to avoid sun glasses fall. -
peltor 3m dab+ headphones wall mount 3D Print Model
Summary
Designed for hearing protection 3m, peltor dab or fm. printed with prusa pla.
Print Settings
Printer Brand:
Prusa
Printer:
i3 MK2S
Supports:
Yes
Infill:
20% -
Base for ZeTime Elite on standard charger 3D Print Model
Summary
If you have a ZeTime Elite with Metalband, you will notice that the charger doesn’t touch the watch if you put it between the watch and the band. With this base under the charger this problem is solved. -
Ol Tri-Shoe 3D Print Model
Summary
With the power supply mounted to the back of my delta, the weight was too much for a single golf ball. I redesigned the original to hold 3 golf balls to better distribute the weight.
Print Settings
Printer:
Anycubic Delta
Rafts:
Doesn’t Matter
Supports:
Doesn’t Matter
Resolution:
0.2
Infill:
50% -
Video Timelaps Track And motorized Carrige 3D Print Model
Summary
This was a fun project to do and im going to share it with you. its a track that fits the cossel delta style printers that have the 240 mm diameter hot bed. you could fit some feet to it and use it free standing too.
If anyone is interested in free standing stand for it let me know i will do some and add them to the files.
to build this project you will need the following items :
1 x Stepper motor BYJ48
3 x Ball Bearings 11 mm OD 5 mm ID
1 x Arduino Nano
1 x micro switch
1 x 10K potentiometer
all easily available online
I will be posting a series of videos on youtube showing how to make this and get it working including the arduino code to program it too.
link to videos https://youtu.be/3NT6WOhc9j0
so please support me by subscribing to my youtube channel and if you turn on the notifications you will know when im adding videos for this project.
any problems please leave your comments below. -
Servo Mount for Foam Wing 3D Print Model
Summary
A servo mount that installs in a 6mm thick sheet foam wing. For standard size servos (40 x 20 mm).
Print Settings
Printer:
Creality CR-10
Rafts:
No
Supports:
No
Resolution:
.2 mm
Infill:
100% -
Storage-for-Snapmaker-accessories_FilamentGuide_ScreenBracket 3D Print Model
Summary
remix de :
https://www.thingiverse.com/thing:2762355
https://www.thingiverse.com/thing:2757715
https://www.thingiverse.com/thing:2683909
https://www.thingiverse.com/thing:2710235
soit un “Storage-for-Snapmaker-accessories_FilamentGuide_ScreenBracket”
bon la conception “fusion” de l’ensemble n’est pas parfaite, je ne maîtrise pas encore les logiciels
Extruder : 200°
Heated Bed : 50°
with supports
Print Settings
Printer:
Snapmaker
Rafts:
Doesn’t Matter
Supports:
Yes
Notes:
see attached files 😀
How I Designed This -
LEGO Star Wars Lightsaber Hilt 3D Print Model
Summary
Model of LEGO Star Wars lightsaber hilt made in Fusion 360. -
Alex Bridge pt 2 3D Print Model
Summary
Part 2 to bridge -
Fan Aperture Base – Remixed 3D Print Model
Summary
I added supports for the aperture blades. I was having a lot of trouble tightening the screws enough to hold the blades flat but also loose enough to still spin the outer ring. Works pretty well now. -
PK380 Magazine Extender 3D Print Model
Summary
Walther PK380 Magazine Extender, add +2 to your PK380 Magazines.
Print Settings
Resolution:
.25
Infill:
100% -
Bahtinov Mask – Celestron NexStar 102 SLT 3D Print Model
Summary
Redesigned this to fit the Celestron NexStar 102 SLT -
Azul Scoretrack Overlay – Board Game 3D Print Model
Summary
This is an overlay for the scoretrack in the board game Azul.
It lays over the scoretrack well, and the cube fits. Depending on the tolerance of your machine, the fit can be a bit tight. You can print it at 101 or 102% to have the cube fit better, but then it will not line up perfectly with the squares on the scoretrack.
[The scoretrack squares are slightly smaller than the cube size, making this a frustrating design.] -
M24 to M22 UK tap adaptor 3D Print Model
Summary
I needed a tap connector for an ebay special tap aerator, unfortunately the tap has a 24mm thread and the aerator a 22mm thread. -
Modular (Vape Juice) Bottle Holders 3D Print Model
Summary
Modular organizers for standard 60mL and 30mL bottles. Designed for vape juice bottles.
With 0.3mm layer height and 10% infill, I was able to print each one in under an hour; they are designed to use a small amount of filament while at the same time being stable enough to hold the bottles and snap together.
I included a “blankModule” so that this design can be modified to organize other items.
There is a smaller and a larger holder for 30mL bottles, the larger one fits the glass bottles, while the smaller one fits the plastic dropper bottles. -
GreenEllipsis OpenSCAD Collection 3D Print Model
Summary
The first in a collection of OpenSCAD modules I’ve developed on the way to making things. Posted here in the hope you might find them useful. -
LED Flat Plate for V-Slot Rail D-Bot 3D Print Model
Summary
Just made these to hold my LED strip (2 rows, one above the other) And they snap into the V-Rail.
Print Settings
Rafts:
No
Supports:
No
Resolution:
0.3
Infill:
100%
Notes:
Nothing special, suggest a skirt to prevent the drooling of the little nubs. But up to the individual. -
Rocket Blasting Off 3D Print Model
Summary
Could use some additional supports on the rocket or perhaps change the angle of the print for better quality. Just a cartoon rocket blasting off. Made it for my son, inspired by those Rocket Mortgage commercials.
Print Settings
Printer:
MP Mini Delta
Rafts:
No
Supports:
Yes
Resolution:
150
Infill:
20 -
flowerpot “STRATOCONIK” 3D Print Model
Summary
I wanted to create series of flowerpot for spring, and here is: flowerpot “STRATOCONIK” -
Delta arm dampener 56mm pitch 3D Print Model
Summary
This dampener is what I use as the rods I use have 56mm pitch (center to center distance on the rods) and 7mm diameter.
Others I found were much too short. I have made sure the model is sliced correctly on S3D as well as Cura etc. I have also reinforced the center arc sides a little as that seems to be where the stress can cause failures on dampeners. Also made the snapping on and off easier by rounding the inner edges of the rod grips.
I advise using PETG or ABS as PLA just isn’t great for this type of attachment.
Print Settings
Printer:
Anycubic Kossel
Rafts:
No
Supports:
No
Resolution:
0.1 – 0.2 (I prefer 0.15)
Infill:
100% -
lincoln plaque 3D Print Model
Summary
Lincoln plaque
Print Settings
Printer:
anet a8
Rafts:
No
Supports:
Doesn’t Matter
Resolution:
0.2
Infill:
20 -
replacement moonroof / sunroof switch for lincoln ls 3D Print Model
Summary
mine was missing so I made this.. -
Vacuum Impeller Housing 3D Print Model
Summary
Needed a small vacuum to clean up my work area after all the messes that accrue. Rather than spend $30 on a small shop vac, I figured it could be an interesting opportunity to see how sturdy of a print I could make while testing out how accurate I could print threads generated in Fusion 360. I went to a local goodwill and bought a corded dust buster for $3, a seal-able ammo can from harbor freight, and a couple other components. In all it cost around $10. I used extra filament which is why the assembly is three colors. overall it works a hell of a lot better than the original used vacuum, but I would’ve maybe chosen a more powerful impeller motor if I were starting over. -
MKS SBASE 1.3 BOX include Dual Mosfet, Four TL-Smoother, and FAN 120mm and Bracket to Alumunium Profile 3D Print Model
Summary
This is MKS Sbase case the dimension is 200x160x63 need a larger printer to do that.
Support for dual mosfet and four TL Smoother
Cooling by 120 mm Fan
add three hole on center to mount to alumunium profile vertically
Print Settings
Printer Brand:
Prusa
Printer:
Prusa Clone
Rafts:
No
Supports:
No
Infill:
20 -
Key Chain, Happy Chinese New Year, Happiness, Spring Festival, 福, 春 3D Print Model
Summary
Key Chain Spinner, Happiness & Spring, 福, 春
To observe the Chinese New Year or Spring Festival, people in China like hanging well-wishing Chinese characters or poetic couplets on their door frames, cars, or other places. The spinner here has Happiness (福) on one side and Spring ( 春) on the side. It is about 45mm in diameter. It might be an interesting 3D design project for those interested. May the little thing bring you peace and happiness!
Print Settings
Rafts:
No
Supports:
No
Resolution:
.1 to .2mm
Infill:
5-20% -
Spcmaker 95 shark fin antenna mount/brace 3D Print Model
Summary
I whipped up this antenna mount for the spcmaker 95. Helps with turtle mode. Also keeps fpv antenna out of the props.
Print Settings
Printer Brand:
Prusa
Printer:
i3 MK2S
Rafts:
No
Supports:
No
Infill:
Solid -
Emoji Headphone Wrap 3D Print Model
Summary
Weird headphone wrap designed to look like an emoji with earbuds -
Syanna Buckle Set – The Witcher 3D Print Model
Summary
About The Model
Here we have a pair of buckles for Sylvia Anna’s (Syanna’s) outfit in the Witcher 3: Wild Hunt.
They are used as follows:
Large buckle – upper waist – 55mm strap.
Small buckle – lower waist – 25mm strap
Obviously being plastic these have a limit on their weight bearing compared to metal, so I suggest a hidden secondary support on the belts, This being said, the largest one has been tested bearing up to 30kg of weight (in PLA at 100% infill) and passed not breaking, so are more resilient than expected.
Support Me
Though I provide this print for free, if you’d like to shout me a coffee or support my work (Patreon’s will get future files earlier than everyone else) – all of which helps me create more of these free models – you can do so on the following links:
Ko-fi: https://ko-fi.com/valentinecostumes
Patreon: https://patreon.com/valentinecostumes
Commissions
If you’re interesting in commissioning other buckles from the Witcher series, or any other file, feel free to contact me on here.
Socials
You can follow me and my work on the following sites:
Instagram
Facebook
Twitter -
Falcata Sword for casting 3D Print Model
Summary
I was looking for a suitable sword for casting in aluminium and found this:https://www.thingiverse.com/thing:1715548
I split it in half, added pegs and removed connectors as they were wildly off.
You can see me casting it here:
-
CR-10 / Tronxy Mittens Cooler 3D Print Model
Summary
Let’s keep it cool!
My take on a better cooler for the CR-10 Tronxy X1/3 type hotend. The stock CR-10 set up can cool the heater block too much if you don’t have it wrapped. The parts doesn’t cool all sides well. My Tronxy X3 didn’t have a parts cooler and the heater block couldn’t get temps over 205C.
I tried a couple other popular coolers but did not fit my original parts blower or just not that efficient.
So the Mittens Cooler evolved. Printed in PETG, it weighs 12 grams. Has a bit fo a twist for a little vortex of air.
Needs a few things: a 5015 blower/fan, a few screws, a bit of rewiring, and a bit of tenacity.
WARINING: It works for me. Your results may vary wildly.
If this helps you, a tip would be nice. At least a like and show your makes.
I’ve gone through dozens and dozens of printed revisions to get to this version. Help keep me in plastic. Thanks!
Please note, this is not compatible with the auto-leveling sensor. Send me one and I’ll try to make one fit.
Print Settings
Printer:
Creality CR-10
Rafts:
No
Supports:
No
Resolution:
0.2mm
Infill:
15%
Notes:
Printed with a 10mm brim. My CR-10 took about 2 hours to print.
2 perimeters/shells, 5 top and 4 bottom layers.
I printed in PLA to get started then switch to better temperature-resistance PETG.
Has a built-in support piece (square patch) that should snap out easily. If not, you may have a bit of over-extrusion.
Post-Printing
Clean up
Break out the square support. Careful using hobby knife, trim away the brim and any stray printed strands.Check the parts blower outlets and clean up as needed.
WARNING: Use at your own risk. I’ve tested this best I can at this time and works great for me. Your results may vary greatly.
Gather parts
existing 40mm fan
M3x12 or possible 10s (2-4) — for mounting fan to Mittens Cooler (should be able to reuse existing screws)
5015 blower/fan (needs to be wired–splice and solder or add a connector)
M3x8 screw — for holding 5015 fan/blower
M3x16 screw (2) — for attaching Mitten Cooler and block to mount (should be able to reuse existing screwsDisassembly
Disassemble the hot end removing the housing screws and the fan mounting screws.
Wire in the new 5015 fan.blower paying attention to red and black wiring.
Save the screws since some can be reused.Assembly
The screws should thread themselves into the Mitten Cooler. If they are super tight, you may be over-extruding. Ream the holes bit and try fitting the screws again.
make sure the printer is off
snap the hot end in the back of the Mitten Cooler with the heater wiring to the left
line up the mounting holes to the top two holes on the finned cooling block
push through the M3x16 screws
check to make sure the parts cooling outlets are above the nozzle opening
carefully line up to the mount
tighten screws — if there is an resistance, make sure the screws are aligned properly
insert the 5015 fan/blower
insert the Mx8 screw in the top hole
tighten screw to snuggle hold the 5015 fan/blower
screw in the 40mm fan using M3x12/16. Can get by with just two screws. Snug but not too tight or you could warp the fan adding more noise
check clearance on everything and the give it a go -
Hook 3D Print Model
Summary
I hung on the hook cooking utensils
Print Settings
Printer:
self made
Rafts:
No
Supports:
Yes
Infill:
20% -
custom lightsaber designed by Mawena Gawe 3D Print Model
Summary
This is a custom lightsaber designed by my friend, Mawena. When I saw his design I went into tinkercad and started working on a 3d design for it
Here are the colors for the different pieces:
silver/light gray: bottom shell, top
black: base and circular part
red: smaller button on control panel
white: longer button on control panel
gold: control panel
dark gray: bottom
How I Designed This
I used tinkercad -
Fox and Hounds Board Game 3D Print Model
Summary
Fox and Hounds is played on a chess board or checkers board sized 8×8. 4 similar colored pawns or checkers as hounds and a single pawn or checker in other color as a fox.
Hounds are placed onto fields b8, d8, f8, and h8. Fox starts set onto e1. Fox moves first.
Hounds hunting the fox. The fox moves diagonally one field range forward or backward onto an empty adjacent square per turn. Hounds can only move diagonally one field forward (towards row 1) onto an empty adjacent square.
Since only diagonal moves are allowed the game is played on the 32 dark fields of the chess board only.
There is no capturing by jumping and no stacking of checkers. Neither by jumping the opponent as in Checkers nor by moving onto its field replacing the opponent.
Fox wins by reaching the other side of the board (8th row where hounds started their hunt).
Hounds win by blocking the fox such that it cannot move anymore (when fox has no legal move left).
If moving perfect then hounds will win.
I have 2 playing pieces for this game with dogs heads even though when I was growing up I plaid this with chess pawns. Enjoy. -
DNA 75/75c Squonk Box Mod 3D Print Model
Summary
Check out the Build Video for full details.
Need some parts?
DNA 75 / 75c BoardStainless Steel Actuators8ml Silicone Squonk BottleBattery ContactsM2 8mm screws & nuts
Truckbed Liner Spray
