Summary
86 diameter.
3-22 diameter
enjoy!
Author: Thingiverse
-
Mini-V Base Plate for 90 Degree Motor Mount 3D Print Model
Summary
So, I had gotten a Mini-V Rail setup for my FT-5 and wanted to mount the motor to a 90 degree bracket on the base plate. Couldn’t find anything on Thingiverse with the correct dimensions for the mounting holes on the base plate, so I came up with this design.
It is currently a work in progress as I have not printed the part yet, but once I get the part printed and test it out, I will make changes as needed. So far, with a first layer print and a position test, the holes match up perfectly.
Print Settings
Printer:
Folgertech FT-5 Resolution:
.2 Infill:
50 -
Smok AL85 Cup Holder 3D Print Model
Summary
Holder for Smok AL85, spare battery, and 22mm juice bottle.
Made to fit in the cup holder of a Mercedes C220 but it should fit other cars.
OD is 65mm
Print Settings
Printer:
Anycubic Kossel plus Rafts:
No Supports:
No Resolution:
.2 Infill:
20% -
Enclosure for Raspberry Pi 3 and Creality CR-10 3D Print Model
Summary
This is an enclosure that is fastened with screws throw the grid at the side of the controller box. Therefore it is specifically made for the Creality CR-10 but will of course fit at other places when one want the box to be permanently attached to something.
The board is fastened by melting those pins like a rivet. -
1:10 RC Touring Car setup wheel 3D Print Model
Summary
62x2mm rubber O ring is needed for proper use. -
OpenRC 1:10 RC Truggy Rim for Monster Truck 10-Spoke Tires 3D Print Model
Summary
This is remix of original OpenRC 1:10 4WD Truggy Concept RC Car Rims.
I used HobbyKing tires:https://hobbyking.com/en_us/hobbykingr-1-10-monster-truck-10-spoke-black-wheel-block-pattern-tire-12mm-hex-2pc.html
And adjust create new rims compatible with original parts.
Car is much wider and has better stability in turns.
Print Settings
Rafts:
Doesn’t Matter Supports:
No Infill:
100% Notes:
I used PETG. ABS will be fine too. No experience with PLA. -
Double Fidget Spinner with Gears 3D Print Model
Summary
Its a double fidget spinner, spin one side and the other side spins on its own -
FTC11722 Happy Relic Key-Chain 3D Print Model
Summary
Just having fun with this FTC season’s game piece that can be found here:http://www.andymark.com/FTC17-18-p/am-3570.htm
Had request to share this thing, so posting it for everyone to use.
Print Settings
Printer:
Sunhokey Prusa I3 Rafts:
No Supports:
No Resolution:
0.2 Infill:
20% Notes:
Had to scale down in order to print. Original model is 10″ high.
On the picture big relic is at 60% scale and small ones is at 20%.
For a key-chain you can probably print even smaller 10-15%% -
FT-5 E3D Mount + Sensor Mount 3D Print Model
Summary
This is an updated version of the FT-5 E3D Stock Bowden Mount V4. I’ve add a mount for an inductive senor.
Print Settings
Printer Brand:
SeeMeCNC Printer:
Rostock MAX v2 Rafts:
No Supports:
Yes Resolution:
.25 Infill:
40% Notes:
REMOVE the supports from all holes!!
Printed with PETG 245C 70C bed. -
Customizable Remix of DJI Spark Floats Water Landing Gears 3D Print Model
Summary
Remix of the floats by “modelsport”. This version has the complete floating gear in one piece – no gluing required. Each gear weights ~30g, so the four add ~120g to the Sparks weight of ~300g.
Attention: With these floats, the Spark neither swims nor flys well! Please watch the video at https://youtu.be/lQo1Fi36_p4 to see what I mean. Maybe with a later firmware update, the copter gets more stable for such kinds of extra weight, but for now…
Useful ball radius values are between 32mm (-> 550g) and 40mm (-> >1kg). Anything below 32mm has a big risk of the Spark touching water during landing.
You may customize the following values:
numFloats – the number of gears to render
ballRadius – a value between 32 and 40
armRadius – the radius of the arm between the motor cover and the ball.
Use rafts to achieve strong contact to the build plate. Paint the balls with coat after printing for better durability. Use the “PaintSupport” model to print a support plate for painting the gears.
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 Plus Rafts:
Yes Supports:
No -
ProStruder 3D Print Model
Summary
These are the 3D printable STLs for the laser cut parts used in the ProStruder. -
Table slider Ultrasport F-Bike 150 and F-Bike 200 3D Print Model
Summary
This is a slider for a “Ultrasport F-Bike 150 and F-Bike 200 table” which I designed because the table was too far away for me. With this pieces the table is ~20cm closer and in addition you can remove the table easily and reduce the width when the bycicle is closed.
You must print “top.stl” 2 two times.
Extra staff you need:
4x screws
4x nuts -
A Cup Of Love 3D Print Model
Summary
A cup of love…
For more models please follow me, will post daily 🙂 -
Banksy Che Rat 3D Print Model
Summary
Here is another Banksy art piece brought to life.
The rat appeared on the historic Red Victorian hotel in the spring of 2010, around the time that Banksy’s documentary Exit Through the Gift Shop hit theaters
Print Settings
Rafts:
Doesn’t Matter Supports:
Yes -
Galaxy S8 car/room mount 3D Print Model
Summary
Hello, I created this because I didn’t want to buy an expensive mount. This is designed for a Galaxy S8. It fits a GoPro mounting system. Works well. Just mount your GoPro mount to anything and this will bolt up to it.Overview and Background
You will need a GoPro mounting system
Lesson Plan and Activity
And a GoPro screw. -
FT Cub Rear Wing Support 3D Print Model
Summary
Upgrade part for the Flite Test Simple Cub RC airplane
When built to the plans the back of the wing that sits on the fuselage does not have a lot of support. The force that the rubber bands exert on the wing can fold the back part of the wing and mess up the wing angle. Two of these supports attached to the wing in that problem area will correct the problem.
I printed two supports with PLA, roughed up the surfaces to glue with sandpaper, and then hot glued the supports in place.
The position of the supports is a few millimeters in from the edge of the fuselage with the wing mounted to leave a bit of space for some rubber band protectors.
I also smear a thin layer of hot glue over the area of the wing that contacts the fuselage to better hold it in place so it doesn’t slide around. This includes the surface of the supports.
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 V2 Rafts:
No Supports:
No Resolution:
0.2mm Infill:
100% -
d-bot Titan Aero print carriage tube holder 3D Print Model
Summary
I made this tube holder to work with the d-bot print carriage for the Titan Aero, which is found at the following link:https://www.thingiverse.com/thing:2253498
This was done so I had a holder for my ptfe tube, and my wiring. I wanted it beefed up a bit, and added some channels for zip ties to make it more secure. -
Nozzle holder (box) 3D Print Model
Summary
A simple nozzle holder with lid. I designed it for the Ultimaker 3 “Hard Core” set by Solex 3D but it can be used for any standard nozzle.
Any suggestion or request is welcome.
Print Settings
Rafts:
No Supports:
No Resolution:
0.2 Infill:
15% -
Tap Alignment Tool (20×20 extrusion) 3D Print Model
Summary
Basics
A printed 3D tool to aid in aligning 20×20 extrusion for tapping and drilling. Basically to help with assembly of printer frame made with 20x20mm extrusion such as the HyperCube or my ongoing design Cubeish! ..
How it works
Slide the tool onto one side of the 20×20, then use the top hole for aligning the tap bit for tapping the ends of the 20×20, or use one of the three M5 holes in the side to assist in fixing one 20×20 to another…
Note: I haven’t printer one yet but will do so and modify design if necessary…
Mike -
Delta 3D Printer for 25 mm Extruction bar 3D Print Model
Summary
This 3D Printer parts for 25mm aluminium extruction. -
Steering Wheel adapter for Pistol Transmitters, Flysky, Axial, etc 3D Print Model
Summary
Be careful to use a screw in the correct size!
Have fun using your 12mm RC car rims/wheels on your Transmitter -
Peopoly Moai Dial Gauge Bracket 3D Print Model
Summary
This is a dial gauge bracket that friction fits on all sides of the build plate. The dial gauge can then be used to ensure the gap between build plate and vat is level on all sides.
The bracket has been designed around the digital dial indicator gauge available from Amazon and other places. It is available under several brand names, such as Neoteck and Wiysond. Here is a link to the Neoteck version on Amazon.
Simply attach the dial gauge to the btracket and secure tight to the bracket with an M6 bolt and nut. Then simply push the bracket onto the edge of the build plate at the required locations. Depending on how central your build plate is in relation to the vat you may need to adjust the bracket in or out slightly to ensure the tip is central on the vat top edges.
NOTE: You will need to adjust the Z Reset Position in the Advanced Menu to 60 to have the right position for the gauge to measure. Once the build plate has settled at the reset position attach the bracket, not before.
Print Settings
Rafts:
No Supports:
Yes Infill:
40% + recommended for strength in the flex arms. -
Hengstler Counter 3D Print Model
Summary
I remixed this to:
make it easier to print by removing the built-in supports under the object
flatten the text detail, screw, and surrounding area, to be more like what I see in similar images of real devices
fiddled with the area where the two parts join. My intent is to use a thin piece of card to separate them rather than print the detail. -
<3 Bay Area California Necklace 3D Print Model
Summary
CA outline with a heart on the SF Bay Area, the home of many silicon valley engineers and designers!
2in long x 0.5in wide
0.2mm layer height
10-20% infill
Print upside down on glass or a nice mirrored finish/shine. I print one in each of my colors to use as a color palate shown. Most are PLA.
How I Designed This
Onshape -
Servo Horn Compatible with Futaba 3F or Hitec H25T 3D Print Model
Summary
My hobby projects often find me needing a servo horn that I don’t have. I wanted to model a horn with the correct splines to fit the standard size servos that I typically use. This Thing includes the model for a round servo horn with splines that are compatible with either Futaba 3F or Hitec H25T spline servos (this covers most newer standard size servos).
The horn is a tight fit and you may need to slightly scale the model to account for your printer’s particularities.
The DesignSpark Mechanical source model is provided. This allows you to make a custom servo horn.
Print Settings
Printer:
Malyan M150 Rafts:
No Supports:
No Resolution:
0.2 Infill:
25% Notes:
Material: PLA
Slicer: Kisslicer v1.5 -
Banksy Rat 3D Print Model
Summary
This is my first attempt to make some Banksy art into an actual print file. This is the NYC Gangster Rat.
Banksy’s ‘Gangsta Rat’ character has appeared at various locations, but perhaps the most well documented ‘Gangsta Rat’ is the one in the picture here, which was first spotted at Moorfields Eye Hospital in London in 2006
Print Settings
Printer:
Monoprice Select Mini Rafts:
Doesn’t Matter Supports:
Yes -
Enhanced Glock Magazine Baseplate 3D Print Model
Summary
Improved baseplate for Glock Magazines.
Positive grip and larger grip size – suitable for IPSC, IDPA or other sporting purposes.
Best to print upright, with high resolution, with a strong material. -
HD SKYSCRAPER 3D Print Model
Summary
Multi HD support vertically
To get more space on your desk
Print Settings
Printer:
Sharebot NG Rafts:
No Supports:
No Resolution:
0.2 Infill:
20% Notes:
Material : PLA
Maximum size HD 128x83x25
Details are upgraded to an improved version -
three ray fidget 3D Print Model
Summary
This is actually a three ray fidget. The barrels’ diameter are 23 mm which is one mm more than real bearings. If you want to me customize please comment. Any remix please be free to do it. 3D print and enjoy it.
How I Designed This -
SNES cartridge wall mount 3D Print Model
Summary
This is a wall mount for Super Nintendo cartridges. It is inspired by the visuals of the PAL SNES console and it prints without support in one piece. The games fit tightly, so if you want the fit to be more loose, then I recommend that you scale it up a bit. The front plate is meant for the SNES logo or game titles. I hope that you’ll contribute and remix this piece with inspiring plates and so on. Enjoy!
Print Settings
Printer Brand:
Printrbot Printer:
Simple Black Rafts:
Yes Supports:
No Resolution:
0.1984 Infill:
15
How I Designed This
I’ve made this design with an online CAD tool called Onshape. It works really well, but when you start to add many features, such as fillets, then it begins to run slowly. -
Destiny 2 – Drang Sidearm – Hunter Edition 3D Print Model
Summary
Since the Collapse, these pistols have been retooled several times to boost their firepower. A worn inscription reads, “To Victor, from Sigrun.”
The legendary sidearm Drang, to scale with Hunter insignia’s on either side of the grip.
If you would like a finished piece I’d be happy to make one for you. Check out my etsy store for more 3D printed fun: https://www.etsy.com/shop/BigBabyProps?ref=seller-platform-mcnav -
C-Mount Adjustable Microscope Stand 3D Print Model
Summary
I threw together this USB Microscope Stand for my 14MP C-Mount Microscope with 180X Lens I purchased off of eBay. I also own one of the cheaper $20 2MP USB microscopes I purchased off of eBay and I have included an adapter for in as well. I wanted to make the stand modular so the adapters are easily exchangeable and also new adapter for different applications can be made and used as well. All parts can be printed on a 200x200x200mm bed 3D Printer. If you own a printer that can go up to 300mm in height like my CR-10 then you can printer the 300mm tall rod instead and take advantage of an extra 100mm of adjust height. I also included a DIY LED ring light mount that can be used for different camera lenses as well.
As for the printing I used PLA with a layer height of 0.15mm, 3-Layer perimeter top and bottom layers and infills ranging from 5-15%
Build List:
Qty (1) – Microscope Stand Base 10% infill (20.76g)
Qty (1) – 30x200mm Rod 10% infill (48.80g)
Qty (1) – Main Housing 5% infill (73.27g)
Qty (1) – Gear Rack Housing 5% infill (85.21g)
Qty (1) – Right Height Adjustment Knob 15% infill (12.70g)
Qty (1) – Left Height Adjustment Knob 15% infill (9.47g)
Qty (1) – Right Adapter for C-Mount Lens 5% infill (19.37g)
Qty (1) – Height Adjustment Ring 10% infill (4.10g)
Qty (1) – M8x1.25 x 11 mm Length Screw for Threaded Stopper 15% infill (1.64g)
Qty (2) – M8x1.25 x 18 mm Length Screw for Threaded Stopper 15% infill (1.86g)
Total weight about 279.04 grams *your mileage may vary
Optional:
Qty (1) – 30x300mm Rod 10% infill (73.06g)
Qty (1) – 2MP USB Microscope Adapter 5% infill (6.19g)
Qty (1) – All 3D Printed Stand Base 200x200mm 5% infill (85.26g)
Qty (1) – All 3D Printed Stand Base 300x300mm 5% infill (174.55g)
Hardware:
Qty (4) – #8-32 x 1/2″ Machine Screws (If you only have Metric then you can drill out the 4 holes in the base to fit what you have.)
As for the 3D printed threads, they fit a little tight at first, but if you slowly work them in and out they wear in a little start to move smoothly, Printing threaded parts at 0.1mm layer height will be helpful (include parts with internal threads)
I used this for the LED ring light and I soldered a connect and used a 12VDC wall power supply:
https://www.aliexpress.com/item/B86-Hot-2Pcs-Bright-White-100mm-Angel-Eyes-33-SMD-LED-Ring-Car-Light/32777360207.html
Print Settings
Printer:
Creality CR-10 Rafts:
No Supports:
No Resolution:
0.2 Infill:
5-15% -
Cat Photo Stand Clip 3D Print Model
Summary
A picture stand that clips on monitors or other things. It is made to snugly fit a monitor 7.5-8 mm thick and hold 1 picture.
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2S Rafts:
No Supports:
No Resolution:
.2 Infill:
20% Notes:
Ears and features are printed at different heights to allow for color changes.
Simply super glue the back to the front when finished printing. -
Miniature Lockers for Lobotomy Board Game 3D Print Model
Summary
Based on paper models created by JudgementDave here: https://boardgamegeek.com/filepage/145100/jds-papercraft-lockers-cabinets-lobotomy
Print Settings
Printer:
Cetus3D Extended Rafts:
Yes Supports:
No Resolution:
.15 Infill:
13% Notes:
I only use rafts because my bed is not heated. -
16×16 camera mount 3D Print Model
Summary
This is tiny camera/VTX combo mount for 16x16mm setups.
I use it with this camera:https://aliexpress.com/item/AKK-BS2-5-8G-48CH-25mW-VTX-600TVL-1-3-Cmos-AIO-FPV-Camera-for-FPV/32804924139.html
But most likely it will fit popular VM275T:https://aliexpress.com/item/VM275T-Upgrade-Ver-HC48-5-8G-25mw-48ch-Picture-Transmission-Integrated-FPV-Camera-w-Magnesium-Light/32821847503.html
I printed it with ABS and camera goes inside veri tight – be carefull.
Probably if printed with some FLEX – it would be better – more easy to install, more secure against crashes…
Print Settings
Printer:
TEVO Tarantula Rafts:
No Supports:
No Resolution:
0.25 Infill:
100% Notes:
I print without supports, but probablu you will need it…Custom Section
-
Send Nudes 3D Print Model
Summary
Just a sign that says “Send Nudes”
simple as that.
Print Settings
Printer:
Anet A8 Rafts:
Doesn’t Matter Supports:
Doesn’t Matter Resolution:
0.2 Infill:
20% Notes:
Just for Fun -
Prusa Mini i3 Printable Frame 3D Print Model
Summary
This is a printable version of Prusa’s “Mini” version of the i3 printer frame and bed carriage. It is designed to be printed out of PLA (less warping) but you could do it out of any material you like.
You will need a LARGE print bed for this! It is designed to fit on the Creality3D CR-10 bed with no modifications.
You can download all of the files for the Mini i3 at https://github.com/josefprusa/Prusa3/tree/master/mini and build your own! -
Council Ricks Fidget Spinner Badge 3D Print Model
Summary
Council of Rick fidget spinner! Make, and enjoy!
Don’t have a printer get prints made at www.animaspiritus.com
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 V2 Rafts:
No Supports:
No Resolution:
200 microns Infill:
7% Notes:
Uses a 608 bearing should slide in nice, you may need to glue the cap on for it to stay anchored. -
support brosse à dents 3D Print Model
Summary
PLA DiscoEasy200
0.1
210°C
Diamétre de la ventouse :
Print Settings
Printer:
discoeasy200 Supports:
No Resolution:
0.1 -
beholder demagorgon 3D Print Model
Summary
This is very much a work in progress, so come back and ill have more done. this is my beholder demagorgon mashup for my d&d group, now please roll initiative. lol
i could really use the feedback on the eye stocks!!!!! idk how to make those look more…. tentacle like. -
Merkava Tank Simple Model Kit 3D Print Model
Summary
Merkava Tank 3D Print Model Kit, play war with the Israeli tank.
Scale 1/100
Settings for FDM/FFF printers (high quality):
Layer height: 0.1 mm
Infill: 50 %
Speed: 50 mm/s
Supports: yes
05 body parts assembled step by step following instruction photos. -
Trekkie Star Trek Wall Art 3D Print Model
Summary
Wanted to finish the trio set of wall art with some Star Trek
Print Settings
Printer Brand:
Prusa Printer:
Prusa Mk2 Rafts:
No Supports:
No Resolution:
.25 Notes:
3M wall tape recommended to hang without damaging the wall -
Leopard Tank Simple Model Kit 3D Print Model
Summary
Leopard Tank 3D Print Model Kit, play war with the German tank.
Scale 1/100
Settings for FDM/FFF printers (high quality):
Layer height: 0.1 mm
Infill: 50 %
Speed: 50 mm/s
Supports: yes
05 body parts assembled step by step following instruction photos. -
K2 Black Panther Tank Simple Model Kit 3D Print Model
Summary
K2 Black Panther Tank 3D Print Model Kit, play war with the North Korean tank.
Scale 1/100
Settings for FDM/FFF printers (high quality): Layer height: 0.1 mm Infill: 50 % Speed: 50 mm/s Supports: yes
05 body parts assembled step by step following instruction photos. -
Texas Instruments Nspire CX cover 3D Print Model
Summary
I received my calc without cover so I made one. I have no idea what the original looks like and what features it has. Sorry. It has integrated supports for the slide in side of 0.4 thickness so you need to turn on single extrusion width walls in your slicer. These do come of easily, much more than regular slicer support for this case.
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 V2 Rafts:
No Supports:
No Resolution:
0.2 Infill:
100 Notes:
I made mine using black PETG with 100% infill for flexibility and strength. I don’t guarantee that less infill won’t make it fragile. -
Snap-on CTC Dual bed levelling jig 3D Print Model
Summary
Designed from scratch using the layout and coarse dimensions from https://www.thingiverse.com/thing:2460482
OnShape link where you can edit to your custom specifications: https://cad.onshape.com/documents/28e0bcaa853c187d0624b81f/w/fd7acef5713bafce038c5cfe/e/7e7969d14473af0ccc5dd0ed
Improvements:
snaps on instead of using magnets or other means
wider base for improved stability
longer support for the indicator shaft
offset on top to allow clearance for the indicator dial
Instructions: printed laying on one side, PLA, infill 15%, no raft or support. The indicator shaft will deform a bit while printing, hence why it’s oversized.
Design notes:
Distance between rails is 70mm, rail diameter is 8mm, indicator shaft diameter is also 8mm. All holes have been oversized to 8.5-8.7mm, this is both to allow for printer tolerances and to make it easier to slide the “carriage”. You can edit the first two sketches to reduce the oversize, if you want a tighter setup.
I currently have about 0.05mm slop/play with this setup, but my bed is warped almost 0.2mm, so the jig play doesn’t affect the readings so much.
The chamfer on top is ugly but allows for better printing without supports.
The snap-on distance is 0.7mm. You can increase it if you want a tighter fit, decrease it if the required force to snap is too high.
Post-printing:
The indicator should be a tight fit (“good enough”) but there is a hole for an M4 screw that’s designed to be tapped. There’s also an M4 nut retainer, if you don’t want to tap the hole. You can also probably just drive the screw in, without tapping, -
紅龍,雙髻鯊可動關節-by orangeteacher 3D Print Model
Summary
紅龍,雙髻鯊可動關節-by orangeteacher
請不要開支撐 (no support is need) -
railhelper 3D Print Model
Summary
When you are installing rail, this object can help you keep it at center. -
RX7 S7 and S8 Solenoid Connector 3D Print Model
Summary
Connector to make a pigtail or adapter for non mazda solenoids.
Standard Power Time Male Connector 33-0626 is needed. -
Dial Indicator Mount for Prusa i3 3D Print Model
Summary
Could not find a good Dial indicator mount for Prusa i3 that would mach the one I bought from Amazon, so i created my own version. Apparently different models have different probe length. -
Commodore 64 Rear Case Hinge Tabs 3D Print Model
Summary
Replacement tab / hinge for repairing the rear upper section of a Commodore 64 “breadbin” style case.
Print Settings
Printer:
Monoprice Maker Select Rafts:
Doesn’t Matter Supports:
No Resolution:
.2 Infill:
100%
Post-Printing
If you are printing the tabs using PLA, you might want to use an epoxy to stick these to your case. They don’t seem to stick very well when clamped to the case and fastened with Super Glue. I took a Dremel and sanded down the broken tabs so they were even with the rest of the lip of the case, then fastened these over the broken section. -
Zeiss 35mm F2.8 ZM Hood 3D Print Model
Summary
Fits Zeiss 35mm F2.8 ZM snuggly, no locking mechanism. Comes with hood cap, fits loosely but secure, you can scale it to your liking. Some minor testing was done and the hood doesn’t seem to cause any noticeable vignetting. I will confirm this once I get the first roll shot with it developed.
Print Settings
Printer:
Malyan M180 Rafts:
No Supports:
No Resolution:
100 Micron Infill:
15% -
Helping Hands 3D Print Model
Summary
This is a single piece version of dougc314’s helping hands design. It has 1/2 inch tapered pipe threads, so you don’t have to glue it to the pipe. Assembly is similar to the original design except with 1/2 inch pipe.
This is compatible with either the original ball and socket joints or my modified version:https://www.thingiverse.com/thing:5578https://www.thingiverse.com/thing:2539262
Print Settings
Printer Brand:
Prusa Printer:
Prusa Mk2 Rafts:
No Supports:
Yes Resolution:
0.2mm Infill:
20% Notes:
In Slic3r PE, I used “support on build plate only” and set the contact Z distance to 0. This is required, otherwise the lower layers of the balls will curl up at the edges and get caught on the nozzle. After printing the support residue can be sanded off. -
Multi Color Spindown 10 Sided Die – d10 d100 d% 3D Print Model
Summary
As an update to my previous spindown d10 dice, I’ve made a two-color version. The two-color version really pops if you have some good colors, and you should even be able to match your favorite dice if you have the right colors.
I mainly use these to track numbers during games, and having them in a spindown order makes it much quicker to tick them up or down by just a couple of points at a time.
There are two sets–one with zero as the lowest number, and one with it at the highest. Use whichever you prefer, or mix and match depending on your intended use.
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2 MMU Rafts:
No Supports:
No Resolution:
.15 Notes:
No infill is necessary, since the digits fill the majority of the body anyway. I printed at .15, but .2 should turn out fine as well. When printing, make sure to orient the models so that the pointy end of the zero face is pointing in the direction of your cooling fan, to maximize airflow over the steepest overhangs. -
713maker gantry with stock hotend cooler 3D Print Model
Summary
This is a cooler/BLtouch mount for the stock hotend with the 713maker gantry. This is still a work in progress -
BOOMERANG90 – Prototype FPV Racing Frame – V0.1 3D Print Model
Summary
My new NEXT GEN Racing drone
BOMERANG90 (Boomerang wtih rotated half)
Low center of gravity – battery is under upper part
Preinstalled GoPro mount
A lot of space for components
TELL ME IN COMMENTS WHAT DO YOU THINK ABOUT THIS FRAME, EVENTUALLY WHAT WILL YOU IMPROVE 🙂
(This one is in size of 2″inches micro, but final version could be for big size racing quads) -
Comma Scope Wheel for Hawke 4-16 3D Print Model
Summary
I’ve designed this comma wheel for my Hawke 4-16
160mm of total size this wheel is equivalent to a big wheel of 260mm OD!!!
Enjoy
Print Settings
Printer:
Flyingbear Rafts:
Yes Supports:
No Infill:
50% Notes:
PLA 1.75mm used to print the wheel -
DJI Mavic Pro cellphone Hood iPhone 6 & 7, Note 4 3D Print Model
Summary
It´s very difficult to fly the Mavic while you stay under the sunlight and properly watch the attached cellphone visor, even if you crank up the brightness to the maximum. This device aims to minimize that stress. It’s detachable, so you can easily fit the parts into the Mavic shoulder bag.
Included are parts to fit iPhone 6 & 7, iPhone 6 & 7 plus and Samsung Note4. The parts named “base”, “sideL” and “sideR” are the same for all models. Only “back” and “top” are customized according to the phone model.
Print Settings
Printer Brand:
Prusa Printer:
Prusa Clone Resolution:
0.25 Infill:
50% Notes:
Printed in PETG. The hood parts are 2mm wide to make the whole assembly as light as possible. If you want to make them thicker, just scale them up in the proper axis in your slicer. -
SCSI2SD Mac SE Bracket 3D Print Model
Summary
Macintosh SE expansion port mount for SCSI2SD v5
My SE has dual floppy drives, and I didn’t want to remove a floppy drive, or mount the SCSI2SD close to the CRT on top of the floppy drives.
Print Settings
Printer:
FF Creator Rafts:
No Supports:
Doesn’t Matter Resolution:
.2 Infill:
25% -
Plinth – Miniature Terrain 28mm 3D Print Model
Summary
These require no supports. They have smaller tops, about 18mm diameter recess. I only had to cut the dress base of the one miniature to fit it in the recess.
Minis shown are four soldiers from the Lionheart board game and four mage knight minis. -
Toolbox 3D Print Model
Summary
I created this model based on STIG_’s 3D Printer Tool Stand https://www.thingiverse.com/thing:1937236. I added and removed some slots to suit my needs and decomposed the model into parts so that I can print each part using Trinus with a printing volume of 120mm x 125mm x 125mm.
Print Settings
Printer:
Trinus Rafts:
No Supports:
Yes Resolution:
0.2mm Infill:
10% -
Oversized Fidget Widget Cube 3D Print Model
Summary
An oversized fidget cube for larger hands. This cube is 40mm by 40mm and perfect for those who need to tinker, fidget and toy with something while in a meeting or class.
The widget consists of a joystick, ball, spinning disk, hourglass, mechanical push button and flicking switch. All parts are able to be 3D printed and created with the addition of a small piece of clear 2mm acrylic perspex and some microbeads available from a local craft or hobby store.
All parts click together sans the push button which requires a spring from a pen to be inserted and then glued shut.
Print Settings
Printer:
ZYYX+ Rafts:
Doesn’t Matter Supports:
Yes Resolution:
0.20 Infill:
25% -
Inn at the Prancing Pony Sign 3D Print Model
Summary
This is the sign from the Prancing Pony in the Lord of the Rings. I hope you enjoy. The pictures are of a really small print, so It is not as detailed as it could be. (Plus there is some ugly stringing) I put a non-commercial license on this. I don’t really know why, Im just going to see how it goes. (If you have any tips, recommendations, or thoughts about Licenses let me know in the comments.) -
Anti-Calvary Spikes Iteration 2 3D Print Model
Summary
This is the second iteration of the Medieval defensive anti-cavalry tile with openlock connections. Also known as Cheval de Frise. They were principally intended as an anti-cavalry obstacles but could also be moved quickly to help block a breach in another barrier. These could be moved and anchored in different locations to prevent cavalry charges or attacks at certain locations. It is a pretty good tile for war game type play by adding more obstacles.
The first iteration is found here.https://www.thingiverse.com/thing:2430558
This has been modified to have the improved interface openlock 6.0 template with different ways of connecting. Also the redesign has spikes going in only one direction with a different spike arrangement. I wanted more variety in appearance in my game.
Print Settings
Printer Brand:
PowerSpec Printer:
PowerSpec 3D Pro Rafts:
No Supports:
No Resolution:
0.2 Infill:
15% -
SJCAM M20 lens cap for flexible filament 3D Print Model
Summary
Simple lens cap for the SJCAM M20. Fits tight. Made for flexible filaments.
Internal ⌀: 21mm
External ⌀: 23mm
Internal hight: 4mm
External hight: 6mm
Print Settings
Printer:
Anet A8 Rafts:
Doesn’t Matter Supports:
Doesn’t Matter Resolution:
0.2 Infill:
100% Notes:
Printing time was about 10-15 minutes @ 45mm/s -
Hypercube Evolution Addons 3D Print Model
Summary
This is a collection of things I created for my build of SCOTT_3Ds great Hypercube Evolution (https://www.thingiverse.com/thing:2254103).
3030_Lack_Foot.stl is a foot which fits 30×30 extrusions and allows mounting the printer. It’s intended to mount the printer on an IKEA Lack table. A 300×300 build platform size hypercube fits well on a Lack table.
CableGuideClip.stl is a CableGuide which fits onto Bosch Style 3030 extrusions. -
Infinity Measuring Template 3D Print Model
Summary
Infinity Measuring Template (inches) in the style of the Micro Arts Studio one.
I have enclosed 2 models, one with the markings on just the top side, the other has measurements on both sides.
Prints perfect with PLA.
Created using Fusion3D.
Print Settings
Printer Brand:
FlashForge Printer:
Creator Pro Rafts:
No Supports:
No Resolution:
0.1000 Infill:
30% Notes:
I would recommend a maximum print speed of 55 mm/s, otherwise you start to run into problems, of course this will depend on your printer.
The infill percentage will be to your preference, but 30% keeps it nice and sturdy.
I sliced with Simplify3D. -
fixation to stare a mirror on the wall 3D Print Model
Summary
a fixation to stare a mirror and a plug to hide the screw -
Minion Stewart 3D Print Model
Summary
Hello~ I made it from tinkercad.
I hope you enjoy my works. 🙂
How I Designed This -
Dremel EZ Lock Cutoff wheel storage container 3D Print Model
Summary
Snap on container to store Dremel EZ Lock cut off wheels. -
Openlock Wall with Hidden Club 3D Print Model
Summary
This is a miniature wall with and without a trap. Size is 2×2 inches. The trap is a falling club hidden in the stones of the wall. The club trap can either be in the hidden position or fallen position.
There is also a wall design without the hidden trap. This design uses the newer openlock 6.0 template with more options for interlocking to other pieces.
Print Settings
Printer Brand:
PowerSpec Printer:
PowerSpec 3D Pro Rafts:
No Supports:
No Resolution:
0.2 Infill:
15% -
Hypercube Evolution X Carriage for 10mm igus Bushings 3D Print Model
Summary
X-carriage for use with Igus JSM-1012-10 bushings and 10mm aluminum or carbon fiber rod. -
Cooler Master Vortex Plus CPU Cooler Mounting Clip 3D Print Model
Summary
Mounting clips for a Cooler Master Vortex Plus CPU cooler.
I had several of these break on me after moving my computer around, so I grabbed the remaining intact ones and modeled them out.
Print Settings
Printer:
Creality CR-10 Rafts:
No Supports:
Yes Resolution:
0.1 mm Infill:
100% Notes:
Printed with PETG for better temperature resistance.
I found the best orientation for these parts is to place Push Pin (A) horizontally with the long edge of the base triangle against the print bed and Push Pin (B) horizontally with the split tip perpendicular to the print bed and supports only on the parts touching the bed.
This is a small part so there will likely be some variation from print to print (mine came out pretty ugly, but functional).
Post-Printing
The slot at the top of Push Pin (B) needs to be cut to extend it out to edge of the part.
This wasn’t included in order to print more solidly, but it may be able to be printed with supports.
This allows Push Pin (A) to be inserted and rotated into the part.
How I Designed This
Designed in Fusion 360; .f3d file is included. -
Multi-color paddle for Hamel Monohull Paddle boat 3D Print Model
Summary
These are the original paddle just split into 3 files: the hub, the 90 degree spokes, and the 45 degree spokes. For those with a multi-color capability (such as the prusa multi-material upgrade for the i3 mk2/mk2s) you can use this to print the wheel in up to three colors. (you could probably further split them with slic3r to customize it more, I suppose) -
Cable organiser for velcro straps 3D Print Model
Summary
Mount with standoff for organising cables with velco straps (2cm wide). I used this in my server cabinet witch is insulated using 2cm foam (therefore the standoffs) -
Smartphone gaming grip with screen magnifier 3D Print Model
Summary
This is an updated version with screen magnifier of: https://www.thingiverse.com/thing:2483276
Printing settings and components:http://horizonlab.co/2017/09/16/smartphone-gaming-grip-with-screen-magnifier/ -
Horus – Eye für den Einbau einer LED 3D Print Model
Summary
Horus – Eye vorbereitet für den Einbau einer 5mm LED und 2x AAA Batterien mit Kippschalter, Inklusive Led-Passung und Kabelführung auf der Rückseite.
Print Settings
Printer:
RF100 Resolution:
0,1 Infill:
25% Notes:
PLA mit 198° -
W1209 Thermostat Box 3D Print Model
Summary
Need 4x M3 screws
Print Settings
Printer:
Anet A6 Rafts:
No Supports:
No -
Honda motorcycle keychain (a remix) 3D Print Model
Summary
I scaled it down to be 50mm long and added a solid backing between the wings so I could do a filament color switch. Printed using TPU.
First I created a 2D outline using the following command in OpenSCAD:
projection(cut=false) import_stl(“/full/path/to/stl”);
and exported a DXF.
Then I imported the DXF into Onshape to remove the gaps between the wings and extrude it a few mm, then exported that as STL.
Then I imported both into Tinkercad to merge the STLs together:https://www.tinkercad.com/things/7UjYYDNdtQZ-honda-keychain
Thanks for the original design! -
Samsung Galaxy Note 5 TPU Case 3D Print Model
Summary
I designed this TPU case for the Galaxy Note 5. It fits perfectly and the buttons and S-Pen remains easy to access.
I upload 2 versions. One with the headphone hole, and one without headphone hole. Last one just because i never use headphones 🙂
Print with 50% – 100% infill for better protection. I recommend 100%. And print in a glass bed, for better finish.
I use this case in my cellphone, so its 100% sure that if you print it, it will fit 😀
Uploads your prints to make me happy.
Print Settings
Printer:
Creality CR-10 Rafts:
No Supports:
Yes Resolution:
.2mm Infill:
50% – 100% Notes:
I recommend 100% infill. -
Printrbot Simple Metal Blower Mount 3D Print Model
Summary
Adding a blower type fan has significantly improved my print quality. I used the following fan, but any similar 75mm blower fan should work, provided it doesn’t draw more than about .4A of current.
https://www.aliexpress.com/item/GTFS-75mm-x-30mm-DC-12V-0-36A-2Pin-Computer-PC-Blower-Cooling-Fan/32665460063.html?spm=a2g0s.9042311.0.0.X9b0Qz
The other fan mounts I found all keep the blower fan at an angle, taking up more space than is necessary. I also found the mounts had no way of securing the blower, and it would rattle around during printing, and always made me feel like it would fall out.
This fan mount keeps the blower in a more secure vertical orientation, and keeps it close to the extruder motor, making it a little more compact. This makes it a bit easier to access the build plate. The mount allows for zip ties to be threaded through the blower mounting holes, firmly securing the blower to the printer.
Print Settings
Printer Brand:
Printrbot Printer:
Printrbot Simple Metal Rafts:
Doesn’t Matter Supports:
Yes Resolution:
0.2mm Infill:
15% -
Customizable slim linear shaft flush mount 3D Print Model
Summary
Flush mount for V-slot extrusion profiles. Based on my 8mm-specific thing, but now customizable for other rod diameteres. -
CoCo Cartridge Shell for NF6X PCBs 3D Print Model
Summary
This is a cartridge shell for the Tandy Color Computer.
Do not forget my website: www.retrodepot.net
The boards that this shell is designed for can be found here: https://github.com/NF6X/CoCoEPROMpak -
individual buttons for Mmintbox 3D Print Model
Summary
I made the Mmintbox for my arduino uno+lcd and didnt have time to mold a button pad from flexible material.
I noticed that the buttons work when you separate them, so modified the design to cut away the solid flat portion so it’s usable as-printed. Probably needs supports. -
Skullspider – Fully articulated 3D Print Model
Summary
This is a slight improvement over DexterMurphy model (link below)https://www.thingiverse.com/thing:1067086
The low polygon skull on old design is replaced with a different and higher detailed variant
A very good desk toy and cool prop for halloween 🙂
Not recommended to be scaled down as the connectors might get easily broken
Print Settings
Printer:
Tevo Tarantula Rafts:
No Supports:
No Infill:
10% lines or 20% grid Notes:
If the connectors don’t stick well on the bed, might be good to use brims instead of skirt -
Projector level wedge 3D Print Model
Summary
This is a 5mm tall wedge shape cut on an 9 degree angle for the purpose of leveling a free sitting projector. To use, place this wedge under the feet of your projector to level it on the surface it sits. -
Heated Bed Bracket 3D Print Model
Summary
I needed a redone bracket for my 300×200 bed so I created this, as the aluminum extrusions I purchased were too long (for the bed). -
hyperion camera tail mount 3D Print Model
Summary
This little Hyperion Camera Tail mount will take your FPV experience to a new level. Its sleek new clip in design allows for you to now see your entire plane while flying. This piece sits on the tail of your airplane and creates a 3rd person view for an entirely new experience! -
Tevo Tarantula controller reset button 3D Print Model
Summary
Simple stop button for the discount smart controller. -
Trinus Display Stand for Kodama Leveling Bed 3D Print Model
Summary
Trinus touch screen stand for leveling bed.
You may need 2 pcs of 3mm x 12mm Metric Flat Head Socket Screw. -
MASP – Museu de Artes de São Paulo 3D Print Model
Summary
Makeup Port for your brushes
Print Settings
Printer Brand:
FlashForge Printer:
Finder Rafts:
No Supports:
No Resolution:
0,1 Infill:
10%
