Summary
I really love the high clearance fang mod made by Tacblades.
I really didn’t like the high pitched whine that my OEM blower fan made though and that’s what lead me to remix this.
This is exactly the same as the original, only this accepts a standard 5015 blower fan instead of the OEM fan in the original.
Print Settings
Printer:
CR-10 Rafts:
Doesn’t Matter Supports:
Yes Resolution:
0.2 Infill:
60-100%
Author: Thingiverse
-
CR-10 High Clearance Fang Mod for 5015 Fans 3D Print Model
-
Fingerspop Groot 3D Print Model
Summary
le Fingerspop est une figurine pouvant se déposer sur le doigt. les enfants adorent, il se les échanges dans les cours de récréation et s’invente des histoires avec.
le Fingerspop et née d’une association entre la société LV3D et moi-même
Si vous n’avez pas d’imprimante 3D cela n’est pas grave vous pouvez toujours les imprimer chez LV3D en cliquant sur ce lien
https: //lv-3d.fr/impression-3d …
Code promo: BRICOLOUPLV3D
PACK « LV3D DÉCOUVERTE » https://lv-3d.fr/produit/pack-imprima…
Voici le lien où vous trouverez tout les modèles existants:https://pinshape.com/users/238658-sebastien-bricoloup#designs-tab-open -
Coffee Grinder Automation 3D Print Model
Summary
So I bought a coffee grinder and discovered I’m far too lazy to grind my coffee by hand… but the coffee is AMAZING when ground by hand…
So… I bought a servo… and modified it to spin forever… (I centered the pot, then cut the nob off it… and ground the gear stop off the gear…)
And I printed a thing… and I used a cheap servo tester to drive this, I suppose if I got fancy I’d program an Arduino Nano to generate the PWM signal I want for a specific amount of time necessary to grind my coffee…
I power it with a USB wall charger… I tested it off a powered USB hub and it seemed fine, but I’d be concerned about amp draw.
M3x26 bolts to hold it on the coffee grinder, M3x8 bolts to hold the servo in… you’ll need an M3 tap.
Print Settings
Printer Brand:
LulzBot Printer:
TAZ 5 Rafts:
No Supports:
No Resolution:
.2 Infill:
25 Notes:
I printed this out of Taulaman 910 Nylon. -
Batman Face Puncher 3D Print Model
Summary
Child’s batman face puncher! fits my 4 year old, 16.5mm finger holes. Designed to be printed with no supports.
Version 0: designed to be infilled with epoxy for smooth finish
Version 1: designed just to be pained. -
Superman Wall Hanger for Quadcopter Guitar Backpack Hat Drone 3D Print Model
Summary
I haven’t printed it yet but should print fine standing up with supports for the arms.
Print Settings
Printer Brand:
RepRap Printer:
RepRap Kossel XL Rafts:
No Supports:
Yes Resolution:
0.2mm Infill:
20% -
Batman Wall Hanger for Quadcopter Drone Guitar Backpack Hat Etc 3D Print Model
Summary
I haven’t printed it yet and the ears and gauntlets might be tricky but give it a shot and see.
Print Settings
Printer Brand:
RepRap Printer:
RepRap Kossel XL Rafts:
No Supports:
Yes Resolution:
0.2mm Infill:
20% -
SureFire Firepak mount/holder 3D Print Model
Summary
Hello, SureFire Firepak fans, this is a mount/holder I designed for the Firepak, you can stick this mounting plate to any were you need, phone, car, RC model, even on the wall, apply the Scotch outdoor mounting double sided tape to the back side of the mounting plate, and stick it on.
Firepak holder.STL
This is good for an iPhone Plus size phone, it’s exactly the shape of the Firepak, and there’s a cut-out for the LOGO, the Firepak placing on the phone is referenced by a Surefire Firepak iPhone 7 Plus case.
Firepak basic holder.STL
This design is the basis mount can be.
Print Settings
Printer Brand:
MakerBot Printer:
MakerBot Replicator (5th Generation) Rafts:
Yes Supports:
Doesn’t Matter Resolution:
0.1 Infill:
10% -
AFTERGLOW PS4 headset strap FIX 3D Print Model
Summary
link to the fix post on my IG (https://www.instagram.com/p/BUeXSMAjafw/?hl=en&taken-by=codename.ide) This is one of those i cant believe it worked prints…i was an amateur…we learn every day! Non the less it will print with supports and when installing on headset keep in mind that you will have to cut headset plastic by the screws to release the wire from the strap….no need to add the metal support strap the headset comes with…the print is very sturdy and retains its shape with enough flexibility to give you a comfortable fit but strong enough to maintain its position on the users head.
Print Settings
Printer Brand:
Prusa Printer:
Prusa Clone Rafts:
Yes Supports:
Yes Resolution:
.1mm Infill:
zigzag at around 15-30% Notes:
This is only the top strap for the afterglow headset… Open with slicer and set print to adequate wall size 1 mm, inner wall outer wall…keep in mind for flexibility you need spacing between the ZIGZAG infill at 15-30%..REMEMBER, keep FLEXIBILITY in mind when tweaking settings..by all means this print CAN NOT BE A SOLID INFILL..
How I Designed This
i BASICALLY measured the straps position from a to b at the base of the straps standing up on both ends then i went with how high the arch went and designed from those parameters with a digital caliper that measures measuring to the tenth of a mm and from edge to edge, measuring heights of holes and angles and how far somthing is from edges…got prety close by first printing a corner of the hole area were screws go into and made sure the size and angles were on point, made proper tweaks, reprint a sample and went with it….it works, chek link… im happy… -
Wall Mount for Makita XOB01/ DBO180 Cordless Random Orbit Sander 3D Print Model
Summary
Wall Mount for Makita XOB01/ DBO180 Cordless Random Orbit Sander
Print Settings
Printer:
Creality CR-10 Rafts:
No Supports:
No Resolution:
0,3 Infill:
15 Notes:
PLA -
funnel with filter 3D Print Model
Summary
Designed to fill UV resin in 250ml Dropprinters’s bottle (with 24mm neck)
When your 3D printing is finish you should empty the tank in resin bottle. In order to remove small waste you can add a paint filter with very fine mesh (190µm). Print the cutting template to cut with right dimensions.
Dimensions:
Outter dimater : 84mm
Height : 66mm
Print Settings
Printer:
Custom 3D printer Rafts:
No Supports:
No Resolution:
0.3mm Infill:
25% Notes:
No particular difficulties. Activate cooling system to have a good slope printing -
DxCommander Guy Ring 3D Print Model
Summary
Having taken our DxCommander out in a bit of a wind a couple of things happened. When it blows about the SWR goes all haywire and under very testing conditions with the bottom guys only it can, and did snap on the bottom section. (easily mended with some cable clips)
So this ring sets out to add another spreader with some guy points
It has been testing over the weekend and looks as if it is going to do the trick.
You will need to fettle the hole so it sits on your mast where you want it.
Printed on Robo R2 with no particular skill
DE MØTDZ -
Wall Key Holder 3D Print Model
Summary
This is basically a quirky and unique mini key holder. Most key rings fit and can be held on the holder. Theres two so you can fit several keys. Also stick it anywhere you’d like, its size makes it flexible for placement. -
MPCNC Universal Holder for Brother Vinyl Cutter 3D Print Model
Summary
This is a model made for HicWic’s Universal Mount for the MPCNC. I used his base Mini Mount and modified it until it would hold my Brother Vinyl cutter to my liking. It is very stable and will not budge when fully inserted. I have no tried to cut Vinyl with it yet, but I imagine that any failure would be due to something other than this part.
You can find HicWic’s original Universal Mount here:
https://www.thingiverse.com/thing:1234989
Print Settings
Printer Brand:
Robo 3D Printer:
R1 ABS + PLA Model Rafts:
No Supports:
Yes Resolution:
0.3mm Infill:
100% Notes:
I doubt it needs to be at 100% infill, but considering how small it is, it meant next to nothing to make it at 100% infill vs something lower. -
Shipping Container Extra Vents 3D Print Model
Summary
I made this part a few months ago for my shipping container to help dissipate the heat from the blaring sun. it turned out working out really good. They don’t take long to print.
I cut a hole with a 1 inch pipe conduit connector size (electrical one inch size connector)
Put silicone on the base
pushed it in
cut a screen to cover the back to prevent skeeters and black flies from entering
and it worked out perfect, air flows nicely and water stays out.
With the rains we’ve been getting lately, I haven’t seen any traces of water. -
stop dogs sign 3D Print Model
Summary
when people don’t see the beware of dog signs or flat out ignore them this is their last chance sign.
Print Settings
Printer:
anet a6 Rafts:
No Supports:
No Resolution:
.3 Infill:
15 Notes:
the dot is for changing colors. -
Tronxy X3 or X3A Y-Stabilizer 3D Print Model
Summary
Just another remix! I kinda feel like a model DJ… Hahaha
Anyways I wanted to use the original but the bolt heads that came with my bed and from the local hardware store where all to large to fit in the recess, fortunately the nuts for the bed are smaller than most “Chinese” I guess. So now you can use large heads on this thingi but flipping them around. Hope its useful. 🙂 -
A larger nut for “fessyFOO’s Yet Another Belt Tensioner” 3D Print Model
Summary
The original nut was a little too small and its edges to sharp for my taste, so I redesigned the outer ring in fusion 360 and smoothed the edges with fillets. The larger outer diameter helps put more force with ease! -
Lisam LS-210 frame and battery protectors 3D Print Model
Summary
First make sure that you measure these in your 3D printing software before printing.
These protect your arm ends and front and back – and are sacrificial to protect your frame from delaminating or splintering – so print a few and save your frame.
The top plate is to protect top mounted batteries from puncturing on the bolt heads.
Here are the cnc files for the actual frame https://grabcad.com/library/lisam210-1
Buy the frame £11 https://www.banggood.com/Lisam-LS-210-210mm-Carbon-Fiber-Frame-Kit-Mini-Quadcopter-p-1001216.html?p=60160590113042017023
Get it quicker for more money – http://amzn.to/2isRHQi
Print Settings
Printer:
Flux 3D v1 Rafts:
No Supports:
No Resolution:
any Infill:
any Notes:
Make sure you measure before printing – get your scale right. -
Mushu Horns 3D Print Model
Summary
I designed these for a Halloween costume. They came out so well that I thought I’d share them.
Cheers!
These were printed one at a time, but I combined them into one file for convenience. Also, These were printed using both ‘black magic’ settings in Cura (“spiralize the outer contour” and “only follow mesh surface”).
Post processing: Light sanding with 600 grit. Dark blue acrylic on the tips, followed by clear coat everywhere. The plastic used was transparent blue PLA from Alchement.
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 V2 Rafts:
No Supports:
No Resolution:
0.2 Infill:
0% Notes:
enable “cool head lift” for best results. Do not over cool this print, otherwise it will likely fail just above the short spike for some reason. -
Toothed Clip/Clamp 3D Print Model
Summary
I made this clip to hold coiled exercise bands so that they wouldn’t flop around. However, it can be used for anything that would benefit from being compressed together like extension cords, audio cables, etc. One could modify it to have a bigger arm radius or be longer/short depending on your needs. I’d also considered putting a loop on one side so that it could be hung on a wall or work station.
Demo: https://youtu.be/4lMVi9G0CzM
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2 MMU Rafts:
Doesn’t Matter Supports:
Yes Resolution:
.15mm Infill:
25% Notes:
I printed both pieces on their sides. Supports were used under the teeth and the arm on Body A. The printer manages fine bridging across the ‘roof’ of the female piece fine, so no supports are needed inside that hole.
Post-Printing
Depending on the your printers accuracy, you may need to take an X-Acto knife to the male end so that it can slide easily in and out of the receiving piece. -
Wooden Timber Post – 28mm gaming 3D Print Model
Summary
Inspired by dungeon columns from Black Scroll Games (https://www.patreon.com/posts/columns-with-14059441) – a wooden timber post for your buildings to give a sense of height & a roof, and add some cover if needed. Remixed the wood from devonjones OpenForge Air Shrine encounter. No supports needed.
Full size is a bit large for my taste, example in pic is printed @ 90% scale. -
BMW Seatbelt Key 3D Print Model
Summary
BMW seatbelt key for heavy items on the passenger side that may make the seatbelt chime to go off. -
Model Ropeway / Ski Lift 3D Print Model
Summary
Extracted the files from the sketchup file created and posted by hein4bloed. No other changes have been made. -
15 Puzzle Game 3D Print Model
Summary
Print yourself a challenge!https://en.wikipedia.org/wiki/15_puzzle
To make chips movement smooth, scrape the box interior with a blade from a utility knife. -
Folding 2-Pen Stand/Case 3D Print Model
Summary
Here’s a neat folding 2-pen case that doubles as a display stand.
Print Settings
Printer:
MakerFarm 12″ i3v Rafts:
No Supports:
No Resolution:
0.2mm per layer Infill:
20%
Post-Printing
Print each half, and use some 1/4″ dowels as hinge pins/pivots -
Daewoo knob Nofrost MultiFlow 3D Print Model
Summary
Temperature control knob in a Nofrost MultiFlow Daewoo refrigerator
Original model on happy3d.fr : https://www.happy3d.fr/en/kitchen/bouton-refrigerateur-daewoo/
Print Settings
Printer Brand:
Ultimaker Printer:
Ultimaker 2 Rafts:
Doesn’t Matter Supports:
Yes Resolution:
200 Infill:
100 -
Folklore Card Holder 3D Print Model
Summary
This is a card holder for the board game Folklore: the affliction by Greenbrier Games.
Needed some help with getting more room on the table for maps and character mats, this seemed to give just enough space.
Will be adding another for those with expansions as well. Working on a token holder for other table top organization. -
2028 Aluminum Extrusion Brace 3D Print Model
Summary
Trying to print a few braces for the 2020 extrusion, if anyone has some extrusions laying around can you see if this works or what is need to make it work?
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2S Rafts:
No Supports:
Doesn’t Matter Resolution:
.20 Infill:
50 -
Everquest Basilisk 3D Print Model
Summary
Pulled from Everquest EQG files. Will need to be scaled up -
Power Supply Mount – BUD NFB-32026 3D Print Model
Summary
Double power supply mount for BUD NFB-32026 enclosure, using this for Christmas display lights enclosure. -
Type R logo plate 3D Print Model
Summary
car logo plate for printing or cnc. Includes the cad files.
My facebook page is here
https://www.facebook.com/largeformat3dprinter/ -
Anet A8 Dial Indicator Back Support Adjustable 3D Print Model
Summary
Warning:
You need to open M4 threads on the linear bearing blocks to use this part!
Description
I made this support to use my dial indicator on a practical way on my printer. I want to hold the dial indicator as close as the extruder center, and it’s hard to that because the whole extruder structure is a little bulky (fans, extruder motor, etc.) so I decided to fix the dial indicator on the back of the linear bearing blocks.
Material:
M4 tap
2-4 M4 bolts
1 M6 bolt and nut to fix the dial indicator
Print Settings
Printer Brand:
Prusa Printer:
Prusa Clone Rafts:
No Supports:
Yes Resolution:
0,16 Infill:
25% Notes:
You need supports if you print on horizontal position -
gopro session strong protective case + glass 3D Print Model
Summary
strong full-body go pro session case, one is open on the back, the other can fit a plastic cap
i attached a dxf with the path for cutting the protective “lens” in 2-3mm of PMMA or PC
also i’ve uploaded a clip to hold the protective lens on standard hollow gopro frames
other photo soon, work in progress -
GraviTrax Kugelbahn Ersatzteile 3D Print Model
Summary
GraviTrax Kugelbahn.
Ich drucke die Teile aktuell mit 3 Wänden, 3 Boden und 5 Deckschichten.
Die Geschwindigkeit beträgt 60mm/s mit 15-20% Füllung.
Weitere Teile werden folgen.
GraviTrax ball track.
I currently print the parts with 3 walls, 3 floor and 5 cover layers.
The speed is 60mm / s with 15-20% filling.
Further parts will follow. -
Pixel Guy 3D Print Model
Summary
A bit unfixed, I had to slice off part of the back last time it was printed. It is a excellent way to test a new 3D Printer. See the slight disabilities of it(with no overhangs). It is a tiny character I made quite a while ago(2015). Any suggestions will be a very large help to how the rest turn out.
Post-Printing -
Internal mesh removed 3D Print Model
Summary
I printed the original in SLA, and have since decided to remove the internal mesh and add resin drainage holes. Folks might find this easier to print with FDM printers as well. -
Double GoPro/Action Cam Mount with Light bar for 2020 Extrusion 3D Print Model
Summary
I made this because I had an extra action cam doing nothing, so I made it to fit my Tevo Tarantula for Octoprint. Ii made it with 2 mounts so I could mount something else to it as well. I made an LED strip light bar to mount to a camera mount.
It is a 45 degree angle away from the extrusion. There is a hole in the light bar to help wrangle the wires, and give it a neater appearance. Look at the picture of the light strip I am using. I did give it 9mm inside width to accommodate differences in brands. These are the ones yo can cut to different lengths. If I can find a link, I will update.
Print Settings
Printer:
Creality CR-7 Rafts:
No Supports:
Yes Resolution:
.2 or .15 Infill:
20-40 Notes:
This is by no means the best settings. This is just what I printed it in. -
18mm 1/100 Tactical Legionnaire with shields 3D Print Model
Summary
WIP, preview, more come soon
use http://www.thingiverse.com/thing:1651415 -
DW660 Quick Release Dust Shoe with ring for attaching skirt 3D Print Model
Summary
This is a simple remix of https://www.thingiverse.com/thing:410266 which is in turn a remix of https://www.thingiverse.com/thing:231219, a dust shoe for the DeWalt 660.
I found it necessary for our applications on our home brew router to have a skirt. This mix adds a ring in the appropriate place to zip tie a skirt to the dust shoe. It also removes some of the interior plastic that kept causing jams with larger wood chips. I am using 3/16″ thick rubber though vinyl or other materials would work just as well.
This is probably obvious, but print this upright. I realize it’s on its side. That was a side effect of importing it for me.
Good support settings are an absolute necessity on this one due to it having to reach up into the part to support the upper area.
I printed this at low resolution and fast speed. For me this helps with bridging which is handy for the cavity that the pin must travel through. Support doesn’t really work there.
Print Settings
Printer Brand:
Printrbot Printer:
Play Rafts:
Doesn’t Matter Supports:
Yes Resolution:
Low Infill:
20% -
3DS Nintendo Switch Cartridge Adapter 3D Print Model
Summary
Inspired by Athankaspen’s DS to Switch Cartridge Adapter. I liked the concept but wanted indents on the sides to pull the carts out with more ease.
The fit is pretty tight for the switch cart. I included the Fusion 360 file and .stp in case you wish to make adjustments.
Print Settings
Printer Brand:
LulzBot Printer:
Mini Rafts:
No Supports:
No Infill:
20% Notes:
I noticed one of my first prints was SLIGHTLY too wide to fit in my 3DS case while others were fine. Also, the print can be a bit tight for the Switch Cartridge. Because of this, I printed at a 0.85mm shell thickness to account for any variances in the print walls.
As a warning: the bottom under the Switch cart opening is fairly thin at 0.5mm.
How I Designed This
Shape based off the model of TBRIshtar’s 3DS Dummy Cartridge. Remodeled the shape in Fusion 360 and added the Switch cart space plus indents. -
AMD Radeon Vega USB stick V2 3D Print Model
Summary
This is the second version of my Radeon USB stick.
The slot is slightly larger to hold different form factors of USB sticks.
The card itself is a slightly shorter and has been reduced to 2.4 inches (from 3 inches) so it looks more like a graphics card than a candy bar. -
S.L.F. Badge 3D Print Model
Summary
This is the Stiff Little Fingers logo on a flat disc.
Made this to replace the badge on my car. Thought it would be rude not to share 🙂 -
Cube 3 spool holder 3D Print Model
Summary
Printing using a 3D Systems Cube 3, when the filament breaks it takes too long to open the cartridge to free the broken filament, feed new one and close the cartridge case again.
To save myself some time, I modified the cartridge case as per picture, created and printed a spool holder as to feed the printer from outside the cartridge. Now if the filament breaks I can easily fix it 🙂
Print Settings
Printer Brand:
3D Systems Printer:
Cube 3 Rafts:
No Supports:
No Resolution:
see notes Infill:
see notes Notes:
designed using Tinkercad
printed on 3D Systems Cube 3
material : PLA
layer thickness : 200 microns
density : almost solid
fill pattern : diamond
no support or sidewalk -
Lee 1000 primer deflector 3D Print Model
Summary
device clips between the two right hand columns on the lee 100 and deflect the odd rouge primer in to the correct place -
18mm 1/100 Tactical Legionnaire jetbike 3D Print Model
Summary
WIP, preview, more come soon
use http://www.thingiverse.com/thing:1651415 and https://www.thingiverse.com/thing:2513943 -
Subtilisin 3D Print Model
Summary
“Subtilisin is a non-specific protease (a protein-digesting enzyme) initially obtained from Bacillus subtilis. Subtilisins belong to subtilases, a group of serine proteases that – like all serine proteases – initiate the nucleophilic attack on the peptide (amide) bond through a serine residue at the active site.”
–https://en.wikipedia.org/wiki/Subtilisin
Of note is that the catalytic mechanism is identical to that of Trypsin.
The STL file contains a representation of the protein in cartoon form with catalytic residues represented as spheres. Model based on the Protein Data Bank entry 1CSE:
–http://www.pdb.org/pdb/explore/explore.do?pdbId=1cse
Model created using VMD:http://www.ks.uiuc.edu/Research/vmd/
Print Settings
Printer:
Me3D Rafts:
Yes Supports:
Yes Notes:
Successfully printed on a Me3D in ABS.
The images are included as a guide to hand-colouring the active site residues. -
improved! control freak for xbox one 3D Print Model
Summary
version 2 of my control freaks
easier to print multiple sizes and stronger legs
Print Settings
Printer:
tevo tarantula Rafts:
No Supports:
Yes Resolution:
0.15-0.2 Infill:
25 Notes:
i suggest between 0.15mm-0.2 resolution any less and it will not come out well -
Chess Set Wireframe – Modified Base 3D Print Model
Summary
A remix of the Chest Set Wireframe by Jun0
Each base has a 1.5mm deep circular indent to fill to give the pieces weight.
Note: Support from Build Platform Only is recommended, and should be removed cleanly if printed properly.
Thanks Jun0 for the great set!
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2S Rafts:
No Supports:
Yes Resolution:
200um Infill:
20% -
Nintendo Switch Game Case Holder 3D Print Model
Summary
Holds 12 games and include nintendo switch logo that can be printed separately and inserted into the case. -
AOTC Male Tusken Raider Helmet 3D Print Model
Summary
Work in progress Tusken Raider helmet. Scaled pretty precisely to my head, your mileage may vary. Check the dimensions in your favorite tool and adjust accordingly.
I have not yet printed this version, but the previous draft was good. I have high hopes that this is the one! -
Abecedario Braille / Braille Abecedary 3D Print Model
Summary
Este es una serie de piezas para la enseñanza de Braille a discapacitados visuales.
This group of pieces was desgined to teach Braille to blind people. -
Drill bit sharpener for (semi)pro rotary tool (36mm) with relief 3D Print Model
Summary
This guide have to be used with (semi)pro rotary tools with 36mm “collar” like Hilda or Profil. Also you need cutting disk 32mm or more (50mm in my case) in diameter and M4x20 with nut.
Angle is 120 degrees with relif angle of 5 degrees.
Направляющая для заточки сверел для полупрофессиональных граверов типа Hilda или Профиль. Для работы (помимо гравера) потребуется так же отрезной диск 32 или более (я использую 50) миллиметров в диаметре, и винт M4x20 с гайкой.
Угол заточки составляет 120 градусов (универсальный), с задним углом 5 градусов (таким образом режущая кромка первая соприкасается с материалом, и сверло сверлит, а не скользит задней поверхностью РК по материалу). -
Part Remover 3D Print Model
Summary
i have used this for a while now, i put the razor blade on the corner of a print and tap the square with my baby hammer. Parts pop right off with no issue, be careful not to damage the print you’re removing.
Print Settings
Printer:
Anet A8 Rafts:
No Supports:
No Resolution:
.2 Infill:
50% -
Kanger toptank mini portection 3D Print Model
Summary
made for to protect my kanger toptank mini from fallings 🙂
Print Settings
Printer:
anet a8 Rafts:
Doesn’t Matter Supports:
Yes Resolution:
0.2 Infill:
30 -
Gadget Wall Mount 3mm Remix 3D Print Model
Summary
Original Credit to PrintTo3D’s Gadget Wall Mount found here: https://www.thingiverse.com/thing:4738
I did printed off his original thing but it ended up breaking on me due to the holes being to small for the screws I was using while I was trying to drill them out to make them bigger. I also created bigger openings on the bottom so I could fit my usb-c charger to my phone while it sat in the holder.
Remixed to make the holes a little bigger to 3mm, dropped the holes down a little bit from the top for more stability, and I ended up cutting off the diagonal front in case someone wants it and doesn’t have a long screwdriver, as it accomodates shorter fatter ones vs precision screw drivers.
Print Settings
Printer:
Maker Select v2.1 Rafts:
Doesn’t Matter Supports:
No Resolution:
.1 Infill:
100 Notes:
I suggest 100% infill. -
Nerf Retaliator Picatinny Rails 3D Print Model
Summary
This was my attempt to make a full length picatinny rail for the retaliator. I believe that the body rail needs to be reduced by 2mm in height to be flush with the barrel rails.
This part requires the elimination of the Nerf rails on the front retaliator barrel. -
The Gangster Support 3D Print Model
Summary
The Gangster Support
Made by Abhi_Le_Createur
-4 inclinations
-Made for 10.1” Tablets (Galaxy tab 4) but fits most phones and tablets in at least one inclination.
-0.2mm layers for best result.
Thanks. -
Homebrew Beer Pin Lock Keg Gas Depressurizer 3D Print Model
Summary
Used to release pressure from a Pin Lock Cornelius keg that doesn’t have a pressure release valve built into the lid. Simply twist it in place and it will keep the gas poppet depressed and allow the pressure to vent through the post.
I printed this with 20% infill using Makergeeks Raptor PLA and it works well. -
Wallet and Key Holder for Small Wallets 3D Print Model
Summary
I couldn’t find one that really fit my usecase so I designed my own! This is designed for very slim wallets or money clips at or around 18mm. I used Scotch Extreme mounting tape to mount it to the wall. I hope this is as helpful to you as it is to me!
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 Plus Rafts:
No Supports:
No Resolution:
.2 Infill:
20 -
Leap Motion and LED stand 3D Print Model
Summary
Leap motion sensor holder with LED set facing user.
This is to part of an installation in which a D/VJ uses the Leap sensor to control audio/video art while facing an audience. The LEDs light up the user, while the organic shape of the sensor holder hides the electronics from the audience.
The Leap motion sensor can be titled to optimize its orientation towards the user, the cable is routed to the left through a slot. A hole in the base is added to route additional cables powering and controlling the LEDs
The Leap sensor holder is adapted from https://www.thingiverse.com/thing:1535393. -
Sriracha Inverter 3D Print Model
Summary
Friends don’t let friend waste Sriracha. This is a small stand to invert a Sriracha bottle so you don’t have to wait for the half-empty contents to flow to the nozzle. -
Nokia/Withings Steel HR 36mm support/charger 3D Print Model
Summary
i remix this for my 36mm steel HR and for closed bracelet
2x m3x10(min) screw
Print Settings
Printer:
c-bot Rafts:
No Supports:
No Resolution:
what you want -
Dragon Clan Families 3D Print Model
Summary
Dragon Clan Family Mon as pictured by L5R Wiki -
Lego Duplo Train Turntable 3D Print Model
Summary
This train turntable is designed to work with Lego Duplo trains with both narrow and wide wheels. One can print any combination of the left and right pieces to create a 2, 4, or 6 way turn table. Enjoy! -
GT Honeycomb Logo 3D Print Model
Summary
Created by extruding the SVG generated by a trace bitmap function of inkscape on the original logo. The extrusion is 2mm but the X-Y size is a bit large so make sure it fits your print bed before slicing. -
The Genius Garnet 3D Print Model
Summary
I’m a big fan of Korean variety show The Genius, where these cubes called “garnets” are used as in-game currency. I decided to design and 3d print some of my own -
Aim Controller Hanger 3D Print Model
Summary
I created this to hang my Playstation VR Aim Controller from a cabinet door. Most existing models available are for a horizontal position, which wouldn’t fit my door. This will allow the controller to hang from the bottom rear corner without strain.
There is a hole for a screw, but I just hung mine with 3M command strips.
This can be printed as is, without supports.
Print Settings
Printer Brand:
Robo 3D Printer:
R1 ABS + PLA Model Rafts:
No Supports:
No Resolution:
.38 -
Merlon con saetera v2 3D Print Model
Summary
Merlón con saetera, para Exin castillos. El los lados tiene unos soportes por si queremos añadir un mantelete. -
Wall mount for Ps4 Slim 3D Print Model
Summary
Finding nothing satisfing on my search for a PS4 Slim Wallmount I made my own version.
After mounting slide your PS in from right to left side. You will find it easier to get rid of the rubber stands befor sliding the PS in.
Print Settings
Printer:
Anet A6 with SkyNet Supports:
Yes Infill:
20% -
Zumspot Case for Raspberrypi 2 &3 3D Print Model
Summary
This fits on top of this excellent case from Esquilo.
https://www.thingiverse.com/thing:1637227
I tried to integrate it with the top case but my printer couldn’t handle it, so it’s just a simple design that fits on top of the case for a raspberrypi 2 or 3 if anybody needs such a thing.
Print Settings
Printer:
Flashforge Finder Rafts:
Doesn’t Matter Supports:
Doesn’t Matter -
Couch Sofa Release Lever Slip-on Replacement Fix 3D Print Model
Summary
The release lever for my couch snapped-off, so I designed this fix for it. Since a “stub” of the original lever still remained, I designed this thing to slip on over the remaining stub. Printed in black PLA to match the couch, though I realize this makes it a bit hard to see in the photos.
The first photo shows the printed part attached to the couch. The second shows the “stub” that the printed part fits over. The third is a reference photo of a still-intact release lever. The fourth is just the part by itself.
Print Settings
Printer Brand:
Prusa Printer:
Prusa Clone Rafts:
Doesn’t Matter Supports:
Yes Resolution:
0.1 Infill:
20
How I Designed This
Fusion360. The .f3d file is included if you wish to tweak it based on the specifics of how your handle broke. -
replacement sterilite container clip 3D Print Model
Summary
I buy lots of these sterilite containers. I imagine a lot of 3D printing hobbyists do. Frequent usage means the clips eventually break. Instead of having to spend another $5 – $12 dollars and throw away a perfectly good container, I drafted a replacement clip.
I know it’s lame, but I use a lot of them and it is wasteful to have to purchase again. The attached image is the container where I keep my coffee. Of course that’s going to break first, using it everyday for over 2 years.
PLA
.3mm Draft
No Support
Hollow / Shell, No Infill
With these basic settings the printed design is stronger than the factory clip. -
Simplified Pikachu 3D Print Model
Summary
Modified the original design so that it is easier for cutting out dough without having to worry about it getting caught in the cracks.
Print Settings
Rafts:
No Resolution:
.15 Infill:
10 -
Eva Duarte 3D Print Model
Summary
Busto de Eva Duarte modelado en Blender para impresión 3d. Odio la política y a sus participantes. -
Gravity Claw with holes for M5 bolts 3D Print Model
Summary
This is an edit of a Gravity claw made to work with M5 bolts (same as a quadcopter motor) -
AK214 lipo protect 3D Print Model
Summary
It is a small modification of a piece to protect the lipo from the screws of the bottom of the frame.
Print Settings
Printer:
Anet A6 Rafts:
Doesn’t Matter Supports:
No Resolution:
0.2 Infill:
40% -
Modular 28mm Scale Ships ~ Expanded 3D Print Model
Summary
Make 28mm Scale ships for all you RPG needs. The
“Blimp” part can be tied to the “Upper Deck” part to make it appear more realistic and secure. The mast can hold a cloth for a sail. More coming soon to: https://www.thingiverse.com/OfAMillionProblems/collections/modular-ships -
Zonestar P802QR2 Simple X Belt 3D Print Model
Summary
Furos adaptados para parafusos de 4,8mm ( o buraco têm cerca de 5,0mm)
Usei arruela e porcas do lado de dentro, para que ao apertar o parafuso force o metal da arruela e porcas e não o plástico.
Print Settings
Printer:
Zonestar P802QR2 Rafts:
No Supports:
Yes Resolution:
0,2 Infill:
40 -
Bronco Concept Wheels 3D Print Model
Summary
I’ve been working on the Bronco Concept truck for a bit and thought I’d upload the wheels.
They are for 1.9 tires. For each wheel, print 2 rings.
I printed mine at .12 to make nice and smooth.
The rings I printed at .24.
Print Settings
Printer:
Creality CR-10 Rafts:
No Supports:
Yes Resolution:
.12 Infill:
70% -
Lego 3D Print Model
Summary
My first printed Lego. Extend the inner part of the bottom a little bit so it could be perfectly clutch with other. -
cable homework 3D Print Model
Summary
cable holder
Print Settings
Printer Brand:
Prusa Printer:
Prusa Mk2 Rafts:
No Supports:
No Resolution:
.1-.2 Infill:
50% -
Charizard (Minimal Supports) 3D Print Model
Summary
Plane cut the bottom to create a uniform flat surface and added supports in MeshMixer -
Krill Bust 3D Print Model
Summary
3D Fan Art of a Krill from The Orville
Print Settings
Printer Brand:
3D Systems Printer:
Cube 3 Rafts:
No Supports:
Yes Resolution:
.150 mm Infill:
20% -
Rock Climbing Stick Clip with pole threads 3D Print Model
Summary
This is a remix of https://www.thingiverse.com/thing:870219
I added threads for a painters pole or broom handle. I also combined it into one file so there is no need to glue it together.
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 Plus Rafts:
No Supports:
Yes Resolution:
.2mm Infill:
20% -
wall mount for the remote from a Phillips 55PUS7181 3D Print Model
Summary
simple wall mount for the remote of a Philips 55PUS7181 TV
Print Settings
Printer:
Anet A8 Rafts:
No Supports:
Yes Resolution:
0.15 mm Infill:
100%
