Effect DLS 3d Models
Category: Free 3D Models
Free 3D models ready to be used in your CG projects such as films, visualizations, games, VR etc. All 3D Models and Free 3D Print Models are available for download in several formats including .MAX, .STL, .FBX, .3DS, .C4D, .OBJ, .BLEND, .DWG, .DXF, .LWO and much more. If you’re in search of high-quality Free 3D assets, we have a huge library of 3d models for all your needs. Also you can visit 3D Models and 3D Print Models category.
-
makita bit holder 3D Print Model
Summary
This bit holder is designed to be as low profile as possible. It holds 2 bits. The bits are held in by friction, but there are also little detent bumps within the holder.
There is a tongue on the holder that goes into the little 1″ long slot (similar to how the standard belt clip attaches). That makes it very secure, but it also means the holder will only fit on the right hand side of the drill/driver. If you want it on the left, print a mirrored version (or I suppose you could drill another hole in the right spot)
I printed this on an Anet A8, using PLA. It took me a few tries to get the fit right, so the bits are held securely but not so tight that they’re impossible to get back out. If you have trouble, the fit can be adjusted by scaling the print slightly or just by using sandpaper.
Use an M4 screw to attach it. -
Parrot Bebop 1 & 2 Key 3D Print Model
Summary
I always misplace my parrot bebop key; not anymore. I recommend making the holes bigger by drilling holes with a 4mm drill bit.
This a remix from this guy, I just made the handle a bit fatter and I drilled the holes bigger:https://www.thingiverse.com/thing:200…
The processhttps://www.youtube.com/watch?v=vOLsS3c-DoU&t=82s
How to use:https://youtu.be/Oo-tq4knm4o
Print Settings
Printer:
Hamlet 3D Printer 3DX100 Rafts:
No Supports:
No Resolution:
.27 Infill:
100 Notes:
I didn’t use any rafts, but I used 3D printing glue. Print it face down, pointing straight up. I used ABS -
flsun cube rod end stop 3D Print Model
Summary
this was made to replace the end stops on my flsun cube as the perspex ones break easily.
Print Settings
Printer:
flsun cube
How I Designed This
this was designed in microsoft builder. -
Trollenium Falcon Warp 9 3/4 3D Print Model
Summary
I don’t know what came over me but I just felt the trolling hadn’t quite reached maximum saturation.
7 different models hidden in there. This is not printable (without more support than model) and no I’m not slicing it up. It was hard enough putting it together.
No rights claimed by me, etc. etc. -
Sleep Pod Tutorial File Free 3D Model
A tutorial will be released featuring this item. So here it is for all to admire. And to follow along.
-
CRX Cup Holder 3D Print Model
Summary
Cup holder for the First Generation CRX. Fits into, and hangs out of, the ash tray. -
Cobra HISS Arctic (GI Joe) 3D Print Model
Summary
I saw a picture for a winter version of the HISS so I made it. The treads have more detail and assembly is a little easier than the standard version I posted in 2015. I used an old toy and a pair of 6 inch calipers to create this 3D file, though I estimated the missiles, blanket, and side rack. As usual, the file is modeled at the size of the actual toy but is intended to be printed at 25%. If you print this larger or smaller it may have too much or too little detail.
I’ve printed these files but have not painted them yet. I’ll post pics after I’ve painted a few of them.
Print the chassis in ‘right-side up’ orientation with supports.
Treads are printed with the “hubcaps” pointed up.
I had better luck printing the missiles horizontal and than cleaning off supports – though this part was designed to be printed pointed up so that might work better for you.
Much respect and gratitude to past and present members of our Armed Forces, you are the “Real American Heroes”. Your sacrifice allows people like me to live in peace, freedom and make silly little toys like these.
This file is free to download. Please note that it is listed as “non-commercial”. Neither you nor I are allowed to buy or sell physical copies of this 3D model. You are allowed (and encouraged) to print copies for your own personal use. If you have downloaded this file from a source other than my site on thingiverse.com they have done so without my permission. Thank you for respecting the rights of the original copyright holder. -
tutor endstop z chasis acero 3D Print Model
Summary
facilita el acceso al endstop del eje z
Print Settings
Printer:
rojo 3d allmetal i3
How I Designed This
solidworks -
chess decoration/decor? 3D Print Model
Summary
made in fusion 360, this thing is something I made in my free time as kind of a doodle and it looks kinda unique so I am sharing it with the world etc…
recommended to print at 30% scale but to each their own
please comment if you print this, thank you. -
Package 3D Model
Additional Info: Package Lavazza Whole Bean Coffee N120118 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
Adjustable 3d Printer Height Adjustment Wheel – M4 Nut 3D Print Model
Summary
Adjustable 3d Printer Height Adjustment Wheel for M4 Nut
How I Designed This
Used Inventor -
Cable-clip atualizado 3D Print Model
Summary
Teste de costumização -
AustinKillgoreTag 3D Print Model
Summary
yeet -
LME12UU Bushing 3D Print Model
Summary
My 1403 Printrbot Simple Metal kit came with bearing blocks that require LME12UU bushings. Hard to find drylin, and even harder to find a quality bearing in this size, a printed alternative works great here. I used a diamond file to sand the sliding surface to a smooth finish. -
8mm rod endstop switch mount 3D Print Model
Summary
Adjustable endstop switch mount for an 8mm rod. Used on my knock-off Prusa i3 -
Drum Key Key Chain (Revised) 3D Print Model
Summary
This is a drumkey I made. There is a hole in it to attach it to a keychain.
All measurements are made in inches.This was revised for 3d printing, so the support goes all the way into the handle to minimize overhang, and also the hole was filleted for better utility. -
Customizable Earbud-Wrap with Fast Release 3D Print Model
Summary
This earbud holder features:
Convenient flat storage when not in use
Business card size, credit card size, and custom sizes
Quick wrapping action
Even quicker release feature. The last loop with the audio jack holds the other loops in place. Release it, and you can release all the other loops instantly.
Two central holes so you can thread the cord through them to keep it handy while you are listening
An optional notch for the slide-off side of the winding
Customizable location of notch for windings relative to earbud holes
Customizable width of slots for the cord
Customizable size of earbud holes
Customizable corner rounding. Make the corners square, even.
If Thingiverse’s Customizer is working, this is your best bet for customizing. If not, open the file in OpenSCAD, change the preset to “Custom” and start playing with the other settings.
Not much in presets yet. The Default matches DavidPhillipOster’s thing that I mixed from. If you find settings that work well for a recognizable pair of earbuds, let me know and I’ll add them to the presets.
Want a feature added? Let me know.
I tried to restrict the ranges of the settings to ones that result in valid models. If you manage to break the model using Customizer, let me know.
Print Settings
Printer:
Monoprice Mini select Rafts:
No Supports:
No Resolution:
0.2 mm Infill:
15% Notes:
These print settings were suggested by DavidPhillipOster for his thing. I went with a heavier infill when the extra features result in thinner sections.
How I Designed This
Remix, OpenSCAD and Customizer
Started with Earbud-Wrap with Fast Release by DavidPhillipOster, added some features suggested by my son, and made it all Customizer friendly.
Owe a debt to Splines for OpenSCAD by teejaydub as well. -
Human Raven 3D Print Model
Summary
just print it and enjoy the humanoid raven
the raven skull were created by sprocket1597https://www.thingiverse.com/thing:2479682 -
Bath 3D Model
Additional Info: Bath BelBagno BB14 N120118 – 3D model (*.3ds) for interior 3d visualization.
-
Speaker holder 3D Print Model
Summary
I am a student a chew valley school and this is for lass work that im doing. you will have to put the jack/aux plug and cable with the battery socket and cable in through the smll hole t the back before you solder it on to the circuit bored. -
Chandelle PL 1:14 3D Print Model
Summary
Ces chandelles ont été dessinées pour accessoiriser une piste de camion RC à l’échelle 1:14 -
Haus 3D Print Model
Summary
Haus für Minitrix Modellbahn
House for Minitrix model train
Print Settings
Printer:
Anet A8 Rafts:
No Supports:
No Resolution:
0,2 Infill:
20% -
Olight S2R bar mount 3D Print Model
Summary
I really like my Olight s2r flashlight. I use it all the time around the house and typically bring it with me as an EDC tool. I designed this handlebar mount so it can now be used as a headlight on my bicycle for night riding. The design is small and simple to print without any supports. Its a tight fit for the flashlight and the handlebar but that’s probably a good thing.
Note: this is for the front part of a Jones H-bar which is about 24mm in diameter. In theory it could work on something a bit bigger but won’t fit on newer 31.8mm bars. The design is still a prototype. I haven’t done much night riding with it yet. I will most likely update it after a month or two of use.
Print Settings
Printer Brand:
Ultimaker Printer:
Ultimaker 3 Rafts:
No Supports:
No Resolution:
.2 Infill:
25% Notes:
This was printed with Colorfabb XT red. No part cooling fan.Custom Section
More Info:
All my uploads are available for you to download and print yourself for your own personal use. If you have any ideas to better my designs feel free to leave a message.
For other parts and projects like this check out my blog:http://trail70engineer.blogspot.de/search/label/3d_printing
You can buy my designs printed by me here:
eBay Store:https://www.ebay.de/sch/legopro877/m.html?item=222619334048&hash=item33d52575a0%3Ag%3A-70AAOSwmZdZkeUJ&rt=nc&_trksid=p2047675.l2562
Shapeways Store:https://www.shapeways.com/shops/t70e -
Split Collar 3D Print Model
Summary
I had need for a split collar, and I ran out of them in metal, so I figured I’d try a 3d printed one. Just print the 2 halves, then tap out the bottom half for 1/4-20 threads. It works great and holds tension on a 3/4″ shaft perfectly. I printed out of PETG with 100% infill for rigidity, and just smoothed out the inside diameter with a sanding attachment on a dremel.
Print Settings
Printer Brand:
SeeMeCNC Printer:
Rostock MAX v3 Rafts:
No Supports:
Yes Resolution:
200 micron Infill:
100%
Post-Printing
Pull off supports and sand smooth with a sander on a dremel.
How I Designed This
Designed in Alibre Design and sliced with S3D. -
Spacedock’s “Guinevere” 3D Print Model
Summary
I made this model for the Youtube channel Spacedock after he revealed an original idea he had for a science fiction story involving this ship. I know I was beaten to the punch in terms of modeling but I wanted Daniel and all of his subscribers to be able to have a physical model of the ship. I do not take any credit for Spacedock, Daniel, or otherwise. I did this to represent his ideas and do not mean to infringe on them. -
TULIPA – lamp protector 3D Print Model
Summary
ABS TRANSPARENT -IN REPLACEMENT OF A TULIPA BALLOON, DO NOT ENTER A LED LAMP
DIAMETER :75 MM, 70 MM, 140 MM -
Flexion Direct Extruder 18mm ABL Mount 3D Print Model
Summary
ABL mount for the “Flexion Direct Extruder Mount V2 for CR-10” by Bratan, seriously took me 20 minutes, if i was good it would of taken me 5, it worked for me on the first print so that being said, nowhere near a finished product…. just thowing this up so it can help somebody else out that cut their cables before designing something that worked with the new direct extruder setup. -
Curtain 3D Model
Additional Info: Curtain N110118 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
Garda Decor Mirror GC 8150 KFH 1165 KFH 1216 3D Collection
Garda Decor Mirror GC 8150 KFH 1165 KFH 1216 3d Models
-
Palmtree Earrings 3D Print Model
Summary
Palmtree earrings I made for a family member over the holiday season. Looks great printed in white / black PLA with either silver or gold hooks (tested). Was going to print these in stainless steel and polish them, but they turned out great in black with gold hooks for the person who wanted them done 🙂
Print Settings
Printer:
Monoprice Select Mini Rafts:
No Supports:
No Resolution:
.2 Infill:
10% -
Creality Cr-10 Toolbox 3D Print Model
Summary
This is a toolbox that also acts as a base for the Creality Cr-10 control box. It keeps the electronics box high so it is better ventilated from the bottom fan. Due to its size I made it in two pieces and glue them together with superglue (I used medium CA). It is my first design in sketchup, feel free to remix.
Print Settings
Printer:
Creality Cr-10 Rafts:
No Supports:
No Resolution:
0.4 Infill:
20% -
Leopard 1 split hull and tracks 3D Print Model
Summary
A simple remix of the Leopard 1 from TigerAce1945, with the tracks of the tank split from the hull for ease of printing. This uses the same turret as the original. Please go and look at his wonderful creations, they are works of art! -
ManaSE Clon Base and Laser Support 3D Print Model
Summary
This is a support for mana se and TTL Power base for laser (i have one of 5W). -
Jabra conference microphone wall mount 3D Print Model
Summary
this is a Jabra microphone wallmount. should be printable without supports -
CGC Classic: Greek Temple Free 3D Model
In this two part tutorial that this file is the source for, learn how to model and render a classic Greek temple using Blender.
-
Jaune Arc from RWBY Armor Pieces 3D Print Model
Summary
Upload of the armor pieces of Jaune Arc from RWBY. They will need to be sized, and possible edited for better usage and cosplay but these are the base files. -
MP Delta Bed Hole Plug (PROTOTYPE) 3D Print Model
Summary
This is for the Monoprice mini delta. The cooling fan blows directly on the the back of the heatbed where the thermistor is and this is intended to plug the hole. There are two prototypes, one with ears for magnets to be attached under the bed and one with no magnets to fit under the bed. The magnetic version is a little too thick to fit under the bed like in the picture but it gets the idea across. I have not printed or tested the non-magnetic version.
Since this is near the actual part that heats up on the bed, be sure to use a high temperature material like ABS or preferably PETG. I originally tried to block the hole with kapton tape but the heat caused it to rip itself apart. Others have used a flash card taped to the inside of the printer. I also suggest using concentric supports for the lip with about 25-30% support density (the lip is small so a lot of support is needed). -
Nerf Rival Apollo Muzzle Brake 3D Print Model
Summary
Does your Nerf Apollo have too much recoil and you just can’t stand it anymore? Are you tired of going to bed with a bruised shoulder and a sore wrist? We can help! SlightlyOddGuy Industries offers the finest solutions to these issues! Let us introduce you to the SlightlyOdd Muzzle Brake!
The SlightlyOdd Muzzle Brake works to redirect the Apollo’s hurricane-like exhaust gasses backward, but away from the user, thereby adding a little forward thrust to counteract the massive kick the weapon generates. The SlightlyOdd Muzzle Brake also adds more mass to your Apollo, which has the same effect! Say “goodnight” to uncomfortable, sleepless nights!
Enjoying this product? Check out our other Nerf-compatible attachments and items!
Print Settings
Printer Brand:
LulzBot Printer:
Mini Rafts:
No Supports:
Yes Infill:
10% -
Fabrikator Mini II V2 ZAxis Fan Mount 3D Print Model
Summary
To improve cooling of PLA on large prints and small I made this to mount a 60mm X 60mm X 25mm Fan to the Z Axis Gantry.
You will need (2) M3 x 8mm to mount adapter to plate and (2) M4 X 30mm to mount 60mm Fan. You can also mount a 40mm Fan for just a little more cooling.
This travels perfectly from 0 Z position to 100 Z position.
Has my PKP (PeaceKeeperPrecision) logo on both pieces.
Print Settings
Printer:
Fabrikator V2 Mini Rafts:
No Supports:
No Resolution:
.2 Infill:
20% Notes:
This was printed with HobbyKing Silver Metallic PLA (210 C – 235 C) and was printed at 217 C 30mms.
I use this connected parallel with hotend fan on ribbon cable and also on really large items I plug directly into 12v source for alot more airflow. -
Locker 3D Model
Additional Info: Locker 2 tv stand – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
Duty rod holder for OBI_pegboards 3D Print Model
Summary
About my pegboard:
I have buyed a pegboard from OBI (https://www.obi.de/lochwandsysteme/lochwand-mit-vierkantlochung-1200-mm-breit/p/9178419).
This pegboard has square perforations with 1cm^2. This squares has the advantage for us owner of 3d printers that you can build your own set of items directly out of the printer.
The normal pegboards are only drilled with 3mm holes, so you need metal hooks because the prints will break with that thickness.
I am offering a series of all my prints for this pegboard for using or inspiration of your own items.
Please think about the needed density of your prints when you are slicing!
i have used PLA with a density between 25 and 50% (often with support, some items you have to clue befor using them). A resolution of 0.2 mm should be enough for your pegboard-items. -
Piston 3D Print Model
Summary
Piston for two-stroke engine
Print Settings
Printer Brand:
Ultimaker Printer:
Ultimaker 2 Rafts:
No Supports:
Yes Resolution:
0.25 Infill:
50
Post-Printing
Link for my Blog
https://wordpress.com/read/feeds/60656075/posts/1755888560 -
Fri3t 3D Print Model
Summary
Jantes pour voiture RC 1/10 avec ou sans déport et pour pneu de 26mm ou 30mm. -
SR9 – Pistol Grip 3D Print Model
Summary
This inserts into the SR9 grip to adjust it to the size of your hand. Nothing fancy but it works.
I printed with no support and had no issues. This is a snug fit and may require minor trimming to slide freely in and out of your gun. -
18mm to 16mm screw diameter adapter for 8X zoom lens 3D Print Model
Summary
My friend bought a phone case that lets him screw on an 8x zoom lens. the problem is that the screw was too small. So I made this adapter that allows it to screw right in. I thought this may be useful to a few people so I decided to just upload it. Enjoy.
It’s an 18mm female to 16mm male.
Post-Printing -
Tokyo Marui Hi-Capa magazine base plate rail mount 3D Print Model
Summary
This is an experimental part for another user. When I get a chance I’ll print it and make some adjustments to the sizing to suit my printer at least. I’ve released this so you can try it out if you want. It’s made to the sizing of the TM HiCapa 4.3 rail, but I have left it fairly easy to resize with some ~120 grit sandpaper. -
Kids Toy Phillips Screwdriver 3D Print Model
Summary
Kids Toy Phillips Screwdriver. My son likes tools so I’ve started creating 3d printable tools for him. -
Napkin Holder 3D Print Model
Summary
“Wife” Can you make me a Napkin Holder??
“Me” – Why yes i can.. Done!!
=) -
Maker Select Plus / Wanhao Duplicator Plus Hotend Fan Bolt Spacers 3D Print Model
Summary
The screws that attach the fan to my hotend in my Maker Select Plus / Wanhao Duplicator Plus bent. Those screws are apparently M3 x 37MM. I couldn’t find those anywhere, so I purchased very common M3 x 40MM bolts, and designed this spacer to make it fit correctly. It goes in between the bolt and the fan.
Print Settings
Printer:
Maker Select Plus Rafts:
Doesn’t Matter Supports:
Doesn’t Matter Resolution:
.1MM Infill:
Doesn’t Matter -
traxxas 4185 Brake Disc 3D Print Model
Summary
i was tired of buying these little guys so i printed them with abs and haven’t noticed a difference
Print Settings
Printer Brand:
MakerBot Printer:
MakerBot Replicator 2X Rafts:
No Supports:
No Resolution:
0.4 Infill:
100 Notes:
i recommend printing in ABS, print should only take about 6 min. -
Jet Fan Grid 40mm 3D Print Model
Summary
Jet design grid for 40mm fan -
iPhone 6 plus, 7 plus ,8 plus charging dock 3D Print Model
Summary
A charging stand for the bigger iphone models including 6 plus, 6s plus, 7 plus and 8 plus. The models get a little bigger with each model so, the tolerances get tighter with newer phone models. Speaker and microphone ports allow you to take calls, listen to music, etc.
Uses stock apple iPhone cable. I noticed 2 variants, one is slightly more rounded, whereas the other is more rectangular. I modeled the rectangular version. Cable is light press fit and doesn’t move once installed.
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2S Rafts:
No Supports:
No Resolution:
.020 Infill:
20% Notes:
Important to have good adhesion as part tension when cooling can pull corners. -
Toy crown 3D Print Model
Summary
Thats basic crown for my daughter toys, i use rubber band to hold it in place, you might try to use 3d printed holder, if you glue it to the crown.
Print Settings
Rafts:
No Supports:
No Resolution:
0.1 Infill:
30% Notes:
Cooling is must probably. -
Fuji X mount revised extension tube 3D Print Model
Summary
After printing the original extension tube designed by IGFARM, I realized that at least on my X_T2, it didn’t lock into place on the camera. I widened the camera contact surface and put in the slot for the pin to lock it into place. I rotated the orientation that he had it in by 180 degrees, so the only support needed is for the top tabs.
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 V2 Rafts:
No Supports:
Yes Resolution:
.1 Infill:
15% Notes:
I printed it on a Monoprice IIIP using PLA at 205 degrees with 100% cooling
Post-Printing
Redesigned faceMounted to my camera
How I Designed This
Not having spent the time to learn the better CAD programs, I did this redesign in Tinkercad. -
Rigid Body Free 3D Model
I made this Rigid Body in Blender 2.78 as a Beginner. I made this blend following a tutorial on the web.
-
SFIC Holder (Control Key Required) 3D Print Model
Summary
This is an ergonomic adapter to make holding SFIC cylinders more comfortable while picking. This will allow the control lug to engage a cavity inside the enclosure to hold the cylinder in place as it would an SFIC housing. Partially hollow through and through to reduce filament and give you access to the rear of the plug.
If you do NOT have a control key, you will need to use this model so you do not need to engage the control position: https://www.thingiverse.com/thing:2776191 -
Bench 3D Print Model
Summary
Fun to make
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2S Rafts:
No Supports:
Doesn’t Matter Resolution:
0.1 Infill:
doesn’t matter -
Yoda Extruder Spinner for MonoPrice Mini V2 5mm hole 3D Print Model
Summary
This is a remix of Force Yoda https://www.thingiverse.com/thing:2781362 reduced in size with a 5mm hole stand so it can be put on your Monoprice Select Mini v2 Extruder Rod.
Used:
PLA
220c on Extruder
50c on Bed
Supports: on all
Quality is up to you but in the Cura screenshot, you can see my inputs.
I used Speed 40
20% fill -
Cover Plate for Headphone Stand by Borchei 3D Print Model
Summary
I like the headphone stand https://www.thingiverse.com/thing:1675682, and made one for a friend with LED’s. I didn’t like that the base was open and the wiring was exposed from the bottom, so I made a simple plate to cover the bottom. Use #4 countersink screws (short ones!) to attach to the bottom. Might want to drill pilot holes for those screws.
Print Settings
Printer:
ANET A8 Rafts:
Doesn’t Matter Supports:
No Resolution:
.2 Infill:
20% Notes:
You should actually print this at the same resolution and infill that you printed the base for the stand at. Use this to cover the wires in the LED version of his base, or just as a cover to hold in a weight for the base should you decide it needs to be heavier to stand up better or something.
Also, when printing the base for the stand, add an additional 4 or 5 more layers to the bottom or use a high percentage of infill so you have something solid to put the screws in to.
How I Designed This
Whipped it up in 3D Builder after printing a stand and being able to get some measurements for it. This Thing isn’t pretty, but it’ll do the job. -
LGPV_6 3D Print Model
Summary
Version 6 of the thing that is in my head but still is not exact…..more to come
Print Settings
Printer:
CR10s Rafts:
Yes Supports:
Yes Resolution:.15
Infill:5%
Notes:
Rotate 90 degrees ti stand on the tail end. can be scaled more than 2000% -
Table 3D Model
Additional Info: Table HMI Noguchi N151117 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
Laver (Simple) for Tabernacle or Temple 3D Print Model
Summary
Simple laver for tabernacle or temple models. -
Numbered Stands for Gloomhaven 3D Print Model
Summary
Added numbers to stands. For Gloomhaven monster standees -
Air Conception Nitro paramotor fuel primer panel 3D Print Model
Summary
This is a primer panel designed for the Air Conception Nitro 200 paramotor. It holds the primer bulb and shut off valve and is designed to use the same components used by Aviator PPG who originally designed and sells the primer system.
Designed to fit in the frame to the pilot’s right and reachable when strapped in. The primer bulb is fitted with M3x6 screws and nuts and the valve is press fit and glued into place. I’ve used Gorilla Glue with much success.
The components are available at:
Valve:https://www.ebay.com/itm/10x-1-4-InLine-Straight-Cut-Off-Shut-Off-Valve-Fuel-Gas-For-BRIGGS-STRATTON/272255821535?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
Primer bulb:https://www.ebay.com/itm/5-Pack-Screw-On-Primer-Bulb-for-Craftsman-Poulan-530047213-530071835-188-513/151310101232?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649 -
Finn – Articulated Toy 3D Print Model
Summary
Finn, from Adventure Time. This is my first attempt at a model with movable parts. In theory, it should print without issue, however if you notice a problem please let me know and I can make adjustments.
Features:
Head and waist swivels
shoulders and legs swivel
elbows and knees bend -
Heart Shaped Box 3D Print Model
Summary
This is my take on the Valentine’s Day heart shaped box. The box is ~70mm x 70mm x 50mm tall. There are two lids with a design and one blank lid if you want to work up something of your own.
Print Settings
Resolution:
0.2 mm Notes:
I printed at 0.2mm. I printed with supports in the hearts but not under at the points. -
texture cube calibration test 3D Print Model
Summary
test calibration of your printer with the texture cube. plus it’s fun to feel. -
Vase 3D Model
Additional Info: Vase Nova LIght N261217 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
