Bear 3D model 3D print modelBear 3D modelUsable for print.Available in multiple formats. Native format is .objSculpted in Zbrush.File contains one mesh object with 800 000 polygons.
Category: 3D Print Models
Premium & 3D Print models ready to be 3d printed. 3D Print Models and Free 3D Print Models are available for download in several formats including .STL, .3DM, .OBJ, .3DS, .DAE, .SKP, .BLEND, .DWG, .DXF, .STEP and much more. If you’re in search of high-quality 3D printed assets, we have a huge library of 3d print models for any of your needs. Also you can visit 3D Models and All 3D Models category.
-
Hippopotamus head 3D Model
Hippo head model for print.Sculpted in Zbrush.File contains one mesh object with 459 836 polygons.Available formats are: .fbx, .stl, .obj, .lwo, .wrlNative format is .objThank you for interest!
-
Eddie – Iron Maiden mascot Fan art 3D Model
Eddie – Iron Maiden mascot – fan artPrintable modelModel is available in multiple formats.Sculpted in Zbrush.File contains one mesh object with 200 000 polygons.
-
Tank2 undated Gear Cases for Kyosho RF006 worm gear set 3D Print Model
Summary
Hey back at it again with the original tank. Have gained a lot of knowledge in the last three years about gear boxes. Going back over the original tank and redoing some things to make it better, lighter, cheaper, easier and stronger. Going to try to keep the original looks and suspension the same. This new gear drive design I have had a lot of luck with and the Kyosho gear drive set has been proven to be indestructible. The new design uses fewer parts and is stronger than the old gear box. Uses a pair of 6x15x5m sealed ball bearings of the worm gear and two 6x16x5m sealed bearings for the shaft. My RF006 Kyosho gear set has the bearing tab cut off the one end. I have supplied a spacer to take up the slack but the original gear may fit in the case without removing the bearing tab. Make sure the worm wheel/axle is centered on the worm gear. There is a access plate that uses two #4×1/4 flat head sms (just in case the screw ever comes loose on the axle gear). Uses a pair of 6-32×1-1/2″ machine screws per side to go through the case and frame. Two #6×1/2 screws for the top frame, four #4×3/4 sms for the inner case and three screws per side #4×3/8 sms for the back plate and two #4×1/4 sms screws to hold the inner bearing and give you some adjustment. Drill #6 screw holes at .140″ (#28), #4 screw holes at .120″ (#31), #6 thread holes at .1065″ (#36) and the #4 thread holes at .086 (#44) on the flat and .093″ (#42) through the layers to keep from splitting.
Print the inner cases with raft and exterior support. Print the outer cases and the parts without raft. I use 2 extra shells and 20% fill. Break off extra tabs and buttons for support.
Have CNC machines up and going finally and will have frames rails and motor plates available on eBay for this tank and probably the old tank also. Search for fastmike tank2.
Always love to hear your comments. Thanks and enjoy! -
Ender 2 Spool Holder 3D Print Model
Summary
Ender 2 spool holder modification to make the printer smaller in z-height. You have to put it into the original spool holder ring and screw the tube onto it. Place it so that the spool is in front of the printer.
With this holder Ender 2 fits perfectly in Ikeas’s Lixhult. http://www.ikea.com/us/en/catalog/products/50328670/
This is my first own creation made with onshape.
Onshape link:https://cad.onshape.com/documents/641bbbc473dd174fe3b61717/w/a251211e59489ef57147337c/e/7e90d25bdd5e6cee71dc52af -
Key storage and chain 3D Print Model
Summary
Someone is asking for this kind of key holder/storage. Grab it if you like. -
Dry-Erase Marker Holder X4 3D Print Model
Summary
The wife complained about her dry-erase markers always walking away from the board on our fridge. (I blame my kids). I fixed that.
This Hold the fine-tipped (11mm wide) thin dry erase markers top-down so the ink is always at the tip.
Print this out and add ANY adhesive backed magnets you want. There should be enough of a recessed area to make them as hidden as possible, though they might need trimming
Dimensions are (L) 57mm (W) 15mm (H) 13mm
Designed in Tinkercad
Print Settings
Printer:
Maker Select V2.1 Rafts:
No Supports:
No Resolution:
.1-.2 Infill:
10-50% Notes:
Resolution really isn’t a thing. I printed it at 50% because I had ALOT of extra filament and it will be handled regularly.
used PETG at 225c with 75c hotbed but PLA should do just fine. -
bl touch mount tarantula E3dv6 + entretoise 3D Print Model
Summary
I needed a spacer for my E3D v6 (in order to fill the void underneath my x carriage so as not to bend it by screwing too hard) and a holder for my 3d bltouch sensor. I had this support so I adapted it to my tarantula.https://fr.aliexpress.com/item/1Pc-Free-Shipping-Reprap-Kossel-For-E3D-V5-V6-Hot-End-Aluminum-Alloy-Groove-Mount-Horse/32642740136.html?spm=a2g0w.search0104.3.2.8aC08W&ws_ab_test=searchweb0_0,searchweb201602_2_10152_10065_5000015_10151_10344_10068_10345_10342_10343_10340_10341_5130015_10541_10084_10083_10305_10304_10307_10306_10302_10539_5080015_10312_10059_10313_10314_10184_10534_100031_10604_10603_10103_10605_10594_5060015_10596_10142_10107,searchweb201603_12,ppcSwitch_4&algo_expid=a04b9763-bf4c-45cb-8299-47732310a210-0&algo_pvid=a04b9763-bf4c-45cb-8299-47732310a210&rmStoreLevelAB=4
I put on line the support as well as the template of drilling / spacer, if someone would like to adapt it to his carriage. The holder has a wire-pass for the sensor as well as a wire-pass on the left rear eg for the wires of the heating cartridge and the probe of the hotend.
Print Settings
Printer:
Tarantula Rafts:
Yes Supports:
Yes Resolution:
0.2 Infill:
50 Notes:
ABS -
BPO Badge 3D Print Model
Summary
Now you too can complete your disguise and go undercover inside the insidious organization known as BPO.
Watch out for Whispers.
This looks best printed in two colors, though if you have a steady hand and can get a nice green, painting by hand to match the show might be nice too. I assume it would be pretty simple to get this to print in multiple colors with a dual extruder printer, too.
How I Designed This
Based off a photo from Daryl Hannah’s Twitter during shooting for the finale and the patches on some of the BPO agents seen in Season 1 (https://twitter.com/dhlovelife/status/915570400511348738).
Took a lot of staring at fonts, but in case anyone’s interested, Gliscor Gothic on dafont looks to be an exact match for the font used on the patch itself.
The DNA strands didn’t copy over well from the image so I found some royalty free clip art and warped it around in Photoshop until it looked close enough. -
Tevo Tarantula Bottom Right Bracket 3D Print Model
Summary
Simple z axis strengthening bracket for bottom right hand corner
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2 MMU Rafts:
No Supports:
No Resolution:
0.2 Infill:
25% -
Monoprice Mini Delta Spindle Rounder 3D Print Model
Summary
I didn’t like the sharp edges of the bent metal spool holder on the Monoprice Mini Delta, so I modelled this up that slips over the spool holder and gives it a nice 26.5mm radius on the spindle. Should smooth out feeding of filament.
Inspired by Enzi1984’s design for the MPSM: https://www.thingiverse.com/thing:2036976
Print Settings
Printer:
MP Mini Delta Rafts:
No Supports:
No Resolution:
.2 Infill:
20% -
ZHAW Soap Dish / Sponge Holder 3D Print Model
Summary
This is a soap dish or sponge holder perfect for catching drips before they reach the counter. The design is based on the Zurich University of Applied Science (ZHAW) logo.
The holder consists of a top “dish” and a bottom “saucer”. STL files are provided for a 6x10cm version that fits common hand soap, as well as a larger 9.5x12cm version that is more suited for sponges.
The design was created in OpenSCAD using the SymmetryCAD library. The dimensions can be easily modified in the code, and the logo could be swapped for another with a minor effort. The tesselation pattern can also be modified to any of the 17 wallpaper groups; the ZHAW logo is tiled with cmm symmetry. -
Flashforge Finder minimum resistance filament holder 3D Print Model
Summary
My Finder kept producing errors because of hard-to-pull filament,so I decided to build a mont with minimum resistance.
I think the pictures are self-exlanatory. If you still have questions, just leave a comment!:) -
Copter 18650×8 3D Print Model
Summary
Copter on 8×18650
Motors 2212
Props 10″ – 9″
frame – 70g
ABS – 25% infil -
RING OF SKULL Free 3D Model
The model is fully ready for 3D printingCan be re-scaled to any size depending on your use or 3D Printable area.
-
laptop keyboard cover 3D Print Model
Summary
I heard you like keyboards so I made a 3D printed keyboard cover so you can keyboard without hitting your keyboard.
This is a cover i made for my 2013 macbook pro so that i could rest my mechanical keyboard on top of the keyboard and not have any of the keys below triggered.
I made it in two parts to ensure that most printers would have the area to accommodate this print.
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 V2 Rafts:
No Supports:
No -
GoPro Session mount for Martian 2 frame 3D Print Model
Summary
30 degree GoPro Mount for martian 2
Martian 2 frames aren’t consistent, this is for the following mounting dimensions
Mounting points are ~45mm x ~32mm
more angles incoming
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 V2 Rafts:
Doesn’t Matter Supports:
No Resolution:
.02 Infill:
20% Notes:
Print flat on screw mounts -
Sunfounder HC-SR04 Case 3D Print Model
Summary
The Sunfounder version of the HC-SR04 is slightly different from most low-budget modules out there. For one, it doesn’t have the protruding crystal oscillator between the emitter and receiver. It also uses a socket to prevent you from connecting the wires incorrectly.
This means that most of the HC-SR04 cases out there don’t work without considerable modifications.
This is a snap-fit case, allowing you to screw the backplate into position and then snap the front part of the case in place.
Print Settings
Printer:
Monoprice Select Mini v2 Rafts:
Doesn’t Matter Supports:
No Infill:
10% Notes:
I was able to print with PLA without supports on a pretty low-budget printer. Your experience may vary. -
DD sensor housing of metal detector 3D Model
DD housing of the metal detector. The size is 260×220 mm.Internal height of the board is 13 mm.The width of the groove is 10 mm.The distance between the ears is 20 mm.
-
monoprice mini select Extruder Lever Arm 3D Print Model
Summary
Warning: The cover is as of yet untested. Tell me in the comments if it needs to be adjusted. This is a drop-in replacement for the monoprice mini select extruder arm and cover. After mine broke the day after my printer was delivered, I found Makerbot’s Replicator 2 extruder design to be the same except for the bearing size. I modified it in Onshape, and the bearing from the MP Select Mini fits snugly. If you had to replace parts other than the arm or cover of the extruder, Makerbot’s other parts should fit fine. I can’t find any dimensional differences between my part and the original, but your experience may vary. Tell me if it works in the comments! doesn’t seem to have any issues with it but if you do end up with problems, download the “fixed” version and try that. I also added a file with both the cap and the arm.
Print Settings
Printer:
monoprice mini select Rafts:
Doesn’t Matter Supports:
Doesn’t Matter Resolution:
0.2 Infill:
40-100%
Post-PrintingHow I Designed This
-
18650 Dispenser, Self Standing, Chunky (Dual version) 3D Print Model
Summary
Tall dual version of Chunky’s 18650 battery holder for 2×10 18650’s.
Print Settings
Printer:
Craftbot XL Rafts:
No Supports:
Yes Resolution:
0.3 Infill:
30 -
Reaper left wrist 3D Print Model
Summary
This is pretty simple full-size model of reaper’s wrist for cosplay. It is tube with enough diameter for put in your hand into wrist.
Print Settings
Printer:
Magnum Creative 2 UNI Rafts:
No Supports:
No Resolution:
0.3 Infill:
15-20 Notes:
Print this from PLA or another plastic without shrinkage. Thickness of wall – 0.6 mm. Wrist cutted Into 2 parts. Also u have connection rods for glueing two parts between themself. If u have high work zone – print full size model. -
Carlon LED Candle Pedestal 3D Print Model
Summary
Pedestal to fit the Carlon battery operated LED candle. This has a cutaway for the window frame, and places the light sensor higher above the window frame. -
Kolovrat pendant 3D 3D Model
The model can be used for production, for casting and machining.STL model is ready for prototyping on CNC and 3D PrintingHigh quality modelweight in gold 13,500 gramsweight in gold silver 9,00 grams
-
NES Homebrew Logo 3D Print Model
Summary
This is a model I made for a friend who create’s homebrew NES games, with this being his logo. I have no idea why YOU, random thingiverser, may want it, but this is mainly here in case I ever lose the original model.
How I Designed This
Fusion 360’s REALLY good for manually converting an image into a 3D model, all I did was trace over a picture given to me and extruded how I thought he’d like it. -
Combine Harvester with Corn Head 3D Print Model
Summary
If there was ever a work in progress, this combine harvester is it. A few hours of work went into this design, and it will likely require a few more. I would love to incorporate parts driven by drive wheels, gears, and chains in later revisions
I would love to hear back from users with what I need change, add etc to make this print better. I know tolerances are too tight on some surfaces, and will likely require some sanding at least to get items to fit. This project will also likely require some glue. I refer to part names by an “American” point of view – passenger side is meant to mean left according to driver (or Port Side).
This machine was very roughly modeled after the John Deere S690 combine (grain) harvester. I don’t have one of these at my disposal, so images from the internet are my best reference. -
The Kulbeda 3D Print Model
Summary
Simple one part print.
Uploaded with faux leather wrap, and without.
All credit to original author: http://steamcommunity.com/sharedfiles/filedetails/?id=271657551 -
Working Designs Logo 3D Print Model
Summary
The logo from the beloved (and sadly gone) Working Designs. -
Taiwan style metal sheet building / 台灣鐵皮屋 3D Print Model
Summary
For more printing object please visit 86Duino facebook and give us a “like” and thanks for the tips…https://www.facebook.com/86duino
喜歡圖檔的好朋友請記得到 86Duino Filament 3D 列印 / 耗材 – 不正經研究中心 粉絲團給我們按讚哦 https://www.facebook.com/86duino
Post-Printing -
3d Printable Clone Armour 3D Model
Fully body armour with the Phase 1 helmet.When printing this armour set orientation, splitting, and slicing is up to you. I recommend splitting object with Z-offset in slicer of choice to minimize the need for support structures and maintain cleanliness of the model. If you have a small build area and need to print in chunks I reccomend Meshmixer.All files are in .obj format. Most slicers accept this but in case yours cant there are free online tools to convert to .stl.Attaching the armour to a costume is also up to you. I tried to include a slight amounth of thickness in places where it would be useful to attach straps using small screws or rivets. The belt area is just the physical pouches. You’ll need to create a belt on your own that the pouches loop onto. The straps as well. Although I did include a shoulder strap object that you can print very thin and depending on the material you use it should have a small bit of flex.The ideal method of creating this armour would most likely be to print, sand, and then cast it into molds using Smooth-On Smooth Cast 45D which is a semi-rigid urethane casting resin.Also keep in mind that you as an individual may have to resize each armour piece respective to your body type.
-
Wings 3D Model
The model is made for CNC machine tools. For a 3D printer.Available formats upon request: .c4d, .obj, .fbx, .ma/.mb, .lwo/.lws, .3ds, .3dm, .dxf/.dwg, .stl.Download 3D Wings .stl, .obj, by WitAnGen
-
3D Printer Tool Stand (without “3D” lettering) 3D Print Model
Summary
I took STIG_’s remix and removed the “3D” lettering from the front since I found it unnecessary and it just increased the print time.
The print in my pictures was printed on a Prusa i3 MK2S at 150% speed and took 12hours47minutes and at a price of $23/kg of spool cost me $5.25.
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2S Rafts:
No Supports:
No Resolution:
0.2 Infill:
10% -
Modular gaming hills 3D Print Model
Summary
This is a set of pieces that lets you make hills for wargaming and roleplaying games. The pieces can be snap fitted together with the applied clip. There are different sizes so check out the possible combinations. Not everything fits with everything visually.
You can make full round hills, or edge hills (from two pieces) or corner hills (from one piece).
You should be able to print with very low infill. I use 5% honeycomb.
The hills on the pictures have been painted with different techniques. The desert hill is painted dark muddy brown the drybrushed with a lighter color. They dark grassy hill is painted black and then drybrushed with lighter and lighter grays. The lighter hills are painted white and then washed with yellow, red, brown and black.
The hills are textured and flocked with a simple technique. Thin down PVA glue with 50% water. Paint on. Sprinkle sand and grit on them. Let dry. Spray or paint with PVA glue 80% water. Let dry again.
Support me on Patreon
This thing is delivered with the outstanding help from my patrons. To help me deliver quality printable terrain models, please pledge $1 or more:
Video presentation
Miniatures used
Sci-fi miniatures used comes from pig-iron miniatures.http://www.pig-iron-productions.com/ -
Shimano BR-M315 Abstandhalter/Distance 3D Print Model
Summary
Dear all,
when bleeding the brakes, you should use an inlet inside the brakes.
I have uploaded two sizes. the larger one really requies full space – so cylinders must be pushed away.
I have been printing it with 40% and 60% infill and it seemed ok, even when pushing the brake.
thanks
christian -
Support alim itopie 3D Print Model
Summary
I have create this piece for itopie with 2mm frame, for 20A power suplie (16.53.99.9cm).
You should be remix this thing by the solidworks file.
Print Settings
Printer:
Itopie Rafts:
No Supports:
No Resolution:
0.4 Infill:
0.2 Notes:
Print in PLA -
Multi Cyclone 3D Print Model
Summary
This is a multi cyclone I made to work as a pre-filter when cleaning the pool – and save a lot of water in the process – minimizing water needed for backwashing. Works fine as filter for the shop vac too.
In the making of this I did a lot of reading-up on the function and math involved in these. The design parameters are by no means randomly selected. The result is an efficient and easy to print cyclone.
In order to separate all the fine particles out, high speed and low travel distance is needed. Achieving this combined with high volume throughput resulted in a setup with multiple combined cyclones.
See post print noted for assembly.
The nozzles are designed to fit pool and shop vac hoses. I you want to use it for a household vac you will need to make a reducer.
This multi cyclone is designed to be printed with no support.
Print Settings
Rafts:
No Supports:
No Resolution:
0.3mm or less Infill:
100%
Post-Printing
Post-printing
File of the blobs and seems off to have a successful marriage between the cyclones and manifold.
You may want to break off one “tooth” on the nozzle to be mounted on the outlet manifold to have a good fit at the skew side. I keept all on mine though for better bond. Try and see what works for you.
Find an air/water tight bucket and makes some holes in the lid that matches the end of the funnels.
Insert funnels in the lid and make and glue it together with hot glue or silicone. -
Portrait 3D Model
Model for CNC and 3D printing machines.Available formats on request: .c4d, .obj, .fbx, .ma / .mb, .lwo / .lws, .3ds, .3dm, .dxf / .dwg, .stl.Download the 3D Model Portrait .obj, .stl, by VitAnGen
-
Corbels – 16 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 17 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 17 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 18 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 19 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 20 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 21 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 22 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 23 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 24 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 25 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 26 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 27 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
-
Corbels – 28 Free 3D Model
STL 3D model – corbelsThe model is ready for prototyping with CNC machining and 3D printing.
