Summary
Remixed a few cavern type walls to use with the Openlock system. These are a little thicker than some of the others but seem to work out okay. Only lengths I have put together are 1.5 blocks long, 2 blocks long and 4 blocks long.
Category: Free 3D Models
Free 3D models ready to be used in your CG projects such as films, visualizations, games, VR etc. All 3D Models and Free 3D Print Models are available for download in several formats including .MAX, .STL, .FBX, .3DS, .C4D, .OBJ, .BLEND, .DWG, .DXF, .LWO and much more. If you’re in search of high-quality Free 3D assets, we have a huge library of 3d models for all your needs. Also you can visit 3D Models and 3D Print Models category.
-
Openlock Cavern Wall set 3D Print Model
-
Soccer Sports Cone 3D Print Model
Summary
This is a very simple soccer cone design for soccor purposes or anything else. I designed this to mark out a race course for my Ofna Ultra LX2e and my Eachine Wizard Racing drone.
This should need no supports and the angle is around 70 degrees
Print Settings
Printer:
Anet A8
Rafts:
No
Supports:
No
Resolution:
any
Notes:
supports should not be needed but print what you prefer. -
Bush 3D Model
Additional Info: Bush Rosa Sanina Wild rose N310118 – 3D model (*.gsm+*.3ds) for exterior 3d visualization.
-
Bed 3D Model
Additional Info: Bed GOSFORD Cranberry N260118 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
Revised MPCNC Belt Mount/Tensioner 3D Print Model
Summary
I liked DodgeDerek’s redesign of the MPCNC Belt Mounts, but for some reason the tabs did not fit my prints of the corner blocks, so I made a new version adjusted to fit. I also adjusted the exit point of the belt for a more linear pull from the “ear” of the corner block. The other part I redesigned is the belt clip. I changed it to engage the belt all the way around the clip instead of just on the top and bottom. Finally, I modified the nut trap to accept a 4-40 nut instead of the metric size that was in the original.
I am using these on my functioning MPCNC and they have thus far worked out very well.
Print Settings
Printer:
XYZ DaVinci Jr. 1.0
Rafts:
No
Supports:
No
Resolution:
0.2mm layer height
Infill:
25%
Notes:
3 perimeters using PLA -
Piper 1 3D Printer assembly stl file 3D Print Model
Summary
This is full model STL file of Piper 1 printer. It is for viewing purposes only.
Piper 1 3D printer main project is at: https://www.thingiverse.com/thing:2794632 -
Gear Coaster 3D Print Model
Summary
The gear coaser is 90mm in diameter.
Print Settings
Printer Brand:
Prusa
Printer:
Prusa Mk2
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
0.25
Infill:
20%
Notes:
I printed it with the multi color option in PrusaControl. -
centryi4k /centriphone /centripro for yi4k 3D Print Model
Summary
This is a centriphone case for the yi4k+. Not 100% sure but I think it should also work with the yi4k and the yi4klite. And the camera fits in there with the original underwatercase.
The handle can be mounted for example on a underwater selfiestick for the gopro.
I highly recommend to print it like seen on the picture. There is a lot of force on it!
If your wires are 2 Meters long and you make one rotation per second you get about 7kg on it and easily 20kg wenn you make two rotations per second. So please first hang 20 kg at the handle to see whether it is stable enough! Use wires which can at least holt 7kg each (3*7kg=21kg). You will probably never make 2 rotations per second, but safty first!
Have fun!
PS: And of course it is just a copy of this one, but fixed for the yi4k: https://www.thingiverse.com/thing:1391102First try
-
Kossel XL / Ultibots D300VS Corner Brace 3D Print Model
Summary
Deltas can be wobbly beasts, so I’ve made this bracket to keep mine a bit more stable. There’s versions of these for Kossel and Kossel Mini already, but I couldn’t find one that fit my Ultibots D300VS so I went ahead and made this.
There’s versions for M3, M4, and M5 hardware, and printable drop in or slide in T nuts to mount the bracket as well.
You don’t need to bolt in all the mounting holes! I put in lots of holes so there would be lots of options in attaching the bracket to the frame.
Sketchup source file included.
Print Settings
Rafts:
No
Supports:
Yes
Notes:
You don’t need a lot of infill on this, just good perimeters. I printed mine at 30% and 1.2mm (3 layers) of perimeter, and 1mm of top/bottom layers.
PLA is probably your best choice for these brackets as it’s stiffness is very good, and there’s not much heat to cause problems. -
Star Wars: Executor Class Star Destroyer Free 3D Model
Model of an Executor Class Star Destroyer, also known as Super Star Destroyer.
Due to the greebles, it has nearly 1.1 million vertices. Since the size of the Super Star Destroyer is 19 km, the scale is 1:100 and not 1:10 as my other models.
The model is totally free to use, but the Star Wars copyright belongs to Disney. -
Pull for IKEA Tupplur Blind 3D Print Model
Summary
The pull on our IKEA Tupplur shade broke the second day we had it. So I made a better one.
Print Settings
Printer Brand:
Wanhao
Printer:
Wanhao Duplicator i3 Plus
Rafts:
Yes
Resolution:
.2
Infill:
20%
Notes:
the supports were a PIA to remove so I left them on the back side facing out the window.
How I Designed This
TinkerCAD -
POV Cell Phone Hat Mount 3D Print Model
Summary
Made this to help me take video from a first person perspective with my smartphone. It’s convenient because then I can immediately share the video to social media. It seems silly but I think it solved a problem so I dont care.
I designed it to work with one of these but it’ll probably work with anything similar:http://amzn.to/2Ct4SJy -
Star Wars: Force Unleashed Jumptrooper Helmet Parts 3D Print Model
Summary
This is the helmet for the Force Unleashed Jumptrooper, it’s already sliced up into manageable parts for a printer. I’m currently printing these out, but if you have any issues please feel free to contact me. -
Car 3D Model
Additional Info: Car VAZ-2107 N250118 – 3D model (*.gsm+*.3ds) for exterior 3d visualization.
-
Sofa 3D Model
Additional Info: Sofa baxter casablanca N171117 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
GalaxyS8_Holder 3D Print Model
Summary
-this is a smartphone-holder for Samsung Galaxy S8 !!without recess for the charging cable!! (maybe also suitable for other smartphone)
-Slot is 8.4mm (0,330709 inch)
-dimensions: 50mm x 50mm x 50mm (1,9685 inch)
Print Settings
Printer:
Anycubic I3 Mega
Rafts:
Doesn’t Matter
Supports:
Yes
Resolution:
0.1
Infill:
35
Notes:
-My settings for PLA 1.75mm (Picture: Cura settings) -
Horizontal filament spool holder 3D Print Model
Summary
This is a two-piece filament spool holder that requires a 6002 bearing. It is mainly intended to be installed on top of a delta printer that has a ‘roof’ with a mount for the bearing, feel free to attempt other ways to install.
Print Settings
Printer:
Kossel XL
Rafts:
Doesn’t Matter
Supports:
Doesn’t Matter
Resolution:
up to 0.32mm layers with 0.4mm nozzle
Infill:
10% or more
Notes:
The bearing hole is a tight 32mm, so a well tuned printer and extrusion is needed and still the fit is tight. -
Hanging heart plaque 3D Print Model
Summary
Can hang up and use little rods on bottom to hag up keys, jewelry, and other small objects.
Name can be placed in middle of heart
Print Settings
Printer:
TEVO Tarantula
Rafts:
No
Supports:
No
Infill:
10% -
Subnautica Cyclops Submarine 3D Print Model
Summary
Decided to take a break from Star Wars ships, and built the Cyclops submarine form the survival game Subnautica. The Cyclops in-game in approximately 54.2 meters long x 12.6 meters wide x 14.2 meters high. It is the largest player controllable vehicle in the game at the moment. To build, the player must find and scan 3 Cyclops bridge fragments, 3 Cyclops hull fragments and 3 Cyclops engine fragment. A Seamoth or Prawn suit can be held in a ventral docking bay. (A very small Seamoth is included in the file. It is to scale with the main Cyclops model.) -
Tape Cutter 3D Print Model
Summary
This was created as a way for me to measure and cut blue tape for my print bed accurately and minimize the waste. First you screw the two parts down to a piece of wood. Mount the cutter part a little shorter than your print bed dimensions. Then you stretch the tape from the cutter side to the measuring side, and then press down on the roller side of the cutter and it will cut the tape the desired length. See pictures if that doesn’t make sense. Please comment, and take pictures if you print this. Thanks.
Print Settings
Printer Brand:
Creality
Printer:
CR-10
Rafts:
No
Supports:
Yes
Resolution:
.2mm
Infill:
20%
Notes:
I would make your walls a little thicker in order to make the post strong enough to withstand pulling on the tape. This is also an all in one print, I found the support super easy to pull out from between the roller and the post, and it spins very easily.
How I Designed This
I designed this using sketchup. -
The Varnerized Prusa 1.0.0 3D Print Model
Summary
Winter of 2018, I created a Prusa i3 clone.
You can build this printer for $250, or less. I did, including the cost of a 1kg spool of ABS.
The frame was based off the Original Prusa MK3 frame, but fabricated from plywood laminations. I created and used router templates (and a flush trim bit) from the Prusa .dxf files.
The rest of the parts closely follow Tom Salanderer’s MK2 Clone “Dolly”, with some customizations for the parts I ordered from AliExpress.
My official github repo for this project is: https://github.com/bvarner/varnerized_prusa_i3
My marlin firmware repo is: https://github.com/bvarner/marlin
I’m getting what I consider absolutely ridiculously good results out of this $250 printer, when compared side-by-side to the same models printed off an Original MK2s.
My long-term goal is to iterate on this, and upgrade the electronics to build a true MK3 clone with Trinamic drivers at some point in the future. That though, will be another ‘thing’. 🙂
Print Settings
Printer Brand:
Prusa
Printer:
i3 MK2S
Rafts:
No
Supports:
No
Resolution:
0.2
Infill:
20%
Notes:
3 Vertical Shells (Perimeters)
Use ABS or PETG. -
HP Desktop/wall/arm PC support 3D Print Model
Summary
This is a support for HP desktop/wall all in screen computer that I’designed because this computer not included ones to use it in a desktop. It is multiposition so you can tilt the computer as you need. You will need add a pen spring and a key ring to complete its functionality.
Print Settings
Printer:
TronXY X3
Rafts:
No
Supports:
Yes
Resolution:
.2
Infill:
5%
Notes:
Printed in ABS, bed 85°C Nozzle: 235°C first layer and 228°C others layers, aquanet spray to bed adhesion, cardboard box to cover the printer while printing. You can print in others materials if you want. -
Arduino pro micro case 3D Print Model
Summary
A case for the Arduino Pro Micro. Just hot glue the sides together.
Print Settings
Printer Brand:
FlashForge
Printer:
Finder
Rafts:
Yes
Supports:
Yes
Resolution:
Whatever
Infill:
WhateverPost-Printing
Put the arduino inside and hot glue the pieces together. One side is for wires and the other side is for a USB cable. -
Sconce 3D Model
Additional Info: Sconce Hector Finch N310118 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
Chair 3D Model
Additional Info: Chair H-104 SG N021217 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
Grainfather Dust Cover 3D Print Model
Summary
I wanted a cover for my Grainfather homebrew system. I understand why the cover is open, but wanted something to keep dust out of it when it was not in use and being stored. This inserts into the class top and is low profile so that it won’t add much height if your storage space is limited. -
Grainfather Switch Cover 3D Print Model
Summary
After upgrading my Grainfather to the Connect control box, the mash/normal switch was no longer necessary. I was always paranoid that I was going to accidentally switch the element to mash when moving it and slow down my brew day, so I was always checking it – even though I never actually had hit the switch. If you take off the plastic/rubber water resistant cover and replace it with this hard shell, then you don’t have to worry about hitting the switch anymore. -
On-Off Switch Bracket 3D Print Model
Summary
I love my inexpensive 3D printer, but I hate the fact that to turn on or off my Startt 3D printer I had to remove transformer plug from rear of the printer. I designed a simple ‘L’ shaped bracket to support a $0.50(US) mini switch. Simply undo 2 screws at the top of 3D printer and secure the bracket.
Print Settings
Printer:
Startt
Rafts:
Doesn’t Matter
Supports:
Doesn’t Matter
Infill:
20%
Notes:
PLA filament 0.2mm layer -
Shortened axe 3D Print Model
Summary
Another mini weapon. Made with a flattened edge for ease of printing.
This is modeled off a weapon i had a character in a dnd game using. It was a pole axe whose haft was shortened to be used one handed.
He was a big guy 😛
How I Designed This
modeled in 3D Studio max -
Ruger Precision RimFire Extended Magazine Release 3D Print Model
Summary
This is an extension for the Ruger Precision rimfire magazine release, it fits snug over the original lever… will not work with the Ruger 10 Round rotary magazines.
Print Settings
Printer:
QiDi X-PRO
Rafts:
No
Supports:
Yes
Resolution:
.15
Infill:
50
Notes:
I used ABS, 50% infill printed on side with support and Brim. For better fitment and finish you will need to file/sand the areas that needed support (bottom side)
Post-Printing
For better fitment and finish you will need to file/sand the areas that needed support (bottom side)
How I Designed This
Areas to file /sand -
birb_chirper 3D Print Model
Summary
This is one of those toys that you whirl around on a piece of string and it makes a chirping sound like a flock of sparrows. I have no idea what they’re called, so I called it birb_chirper.
Print Settings
Printer:
Reach 3D
Rafts:
Doesn’t Matter
Supports:
Doesn’t Matter
Resolution:
0.3 mm
Infill:
0%
Notes:
This is a thin-walled model, so use at least two shells and no infill for smooth walls.
Post-Printing
Take a piece of thin string about 1 metre long (I used micro-cord, very fine paracord), pass it through the hole in the tip, then tie off a jam knot that’s big enough to stop in the hole in the top but still pass back through the slot in the side. Now whirl the thing around fast by the string, and it should start to chirp.
This is intended for the amusement of small children and the annoyance of adults.
How I Designed This
The tip of this thing is an ogee curve. I’ve included my library for creating simple ogee and ogive profiles. -
Sparkmaker Replacement Leadscrew nut 3D Print Model
Summary
Due to the slack of the leadscrew nut on the stock sparkmaker unit.. i make a replacement for it.
This nut is around 7mm thick.. if you need a longer type, do pm me.. i will upload.
NOTE.. After print .. DO grease and run Through the Nut with the leadscrew first, it kind of tight.. Once it has go through and re-assemble back to the unit, recommend to run the liner movement print code and let it finish the whole cycle.. 🙂
Print Settings
Printer:
Anycubic kossel min K2
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
0.1
Infill:
100
Notes:
Type of filament reco for this application:
-POM
-PP
-PLA
Do print with 100% infill to ensure the parts are strong. -
AM8 Electronics Case with 120mm Fan Cover 3D Print Model
Summary
I loved this design by feenix82, especially the internal cable management, but wanted it to fit the AM8 Misumi Extrusion Frame. I only adjusted the tabs here to fit the frame. After printing I realized I made the tabs a little too thin and the screw would bottom out, therefore you may need to add a washer under the screw head to prevent that. The cover with 120mm fan is awesome but for some reason my printer had issues printing the honeycomb pattern horizontally so I got rid of them. This may actually improve airflow as it’ll pull more air from the sides of the case and out the front. Who knows. Either way, I like that the motherboard and mosfet is enclosed and this should provide some much needed cable management.
Print Settings
Rafts:
No
Supports:
Doesn’t Matter
Resolution:
.2mm
Infill:
15%
Notes:
I printed with supports but many say you don’t need it. In my case it may have caused more issues as in trying to remove supports I broke some of the cable management loops inside and had to glue them. You’ll have to try it and see how it works with your printer. -
Removable Bed Levelling Probes for Delta Printers 9.5mm effector 3D Print Model
Summary
This is a remix/remake of Removable Bed Levelling Probes for Anycubic Kossel Linear designed by peaberry for 9.5mm effectors.
Attached FreeCAD files.
Print Settings
Printer:
prusa i3
Rafts:
No
Supports:
No
Resolution:
0.2
Infill:
30% -
Bed Frame Reinforcement A3 3D Print Model
Summary
Exactly the same model as made by AndresVH with the exception of the plate gap. The gap was narrowed to fit a JG Aurora A3. -
Storage bin with mount – for under bench etc 3D Print Model
Summary
Storage bin with mount that you can screw under a bench or something like that.
I made the holes for the screws for common tree screws 3,9mm X 40mm.
Print Settings
Printer Brand:
Creality
Printer:
CR-10S
Rafts:
Yes
Supports:
Yes
Resolution:
0.15
Infill:
20% -
Graveyard at St Micheals cemetery Free 3D Model
Graveyard at St Micheals cemetery, Pensacola, Florida, USA. Capt. Jos P. Fish, born in Noank (Connecticut) the March 1 1857 and died May 2, 1919. Made with ReMake and ReCap Pro from Autodesk.
-
Leatherman Rebar Clip Holster 3D Print Model
Summary
I was tired of my leatherman spinning in my pocket so I designed this. It can be clipped inside your pocket or to your belt.
Print Settings
Printer:
Anet A8
Rafts:
Yes
Supports:
Yes
Resolution:
0.1 – 0.2 mm
Infill:
30%
Notes:
May want to use raft or brim to make sure it doesn’t fall over. Use supports below clip but not inside it. -
Flat Print Cable Chain V2 ( No Glue ) 3D Print Model
Summary
This is a flat printed Cable Chain that is folded into the final shape. This gives you a stronger, cleaner part that will move smoothly.
Print Settings
Printer:
Hypercube
Rafts:
No
Supports:
No
Resolution:
0.2 initial layer, 0.1 layers, 0.2 Nozzle.
Infill:
50%
Notes:
The clip needs to be printed in the given orientation so that it has the maximum strength during flexing. After cleanup ( I use PETG so it can be blobby ) reheat the link to 80C on the bed to prevent stress during bending. -
Better Filament Holder for Prusa i3 3D Print Model
Summary
this is a better filament holder for your Prusa machine.
Print Settings
Printer Brand:
Prusa
Printer:
Prusa Mk2
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
.25
Infill:
20-30% -
Simple raspberry pi zero case 3D Print Model
Summary
Simple raspberry pi zero case only needs 4 m2x10mm screws and 4 m2 nuts. -
Wiible vase. 3D Print Model
Summary
I convinced My Mum to buy some Midnight tulips so I made her a tiny display vase for the first that pops up. -
Arbor 3D Model
Additional Info: Arbor N240118 – 3D model (*.gsm+*.3ds) for exterior 3d visualization.
-
Armchair 3D Model
Additional Info: Armchair Rumba Jori N010118 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
Wall holder for Flashforge Creator Pro Original Spool holder 3D Print Model
Summary
Here is a wall holder for the original spool holder of the Flashforge Creator Pro. Of course, it also mount alternative holders designed for the Creator Pro.
( I had first attached the spools above the printer but then realized that the conduction of the teflon tubes doesnt work well. Thus, these have then attached under the printer. That worked a lot better. )
Print Settings
Printer Brand:
FlashForge
Printer:
Creator Pro
Rafts:
No
Supports:
Yes
Resolution:
0,2mm
Infill:
15% -
Tevo Tornado – Creality CR-10 Lights (low cost) 3D Print Model
Summary
Système de Leds à petit prix pour l’éclairage de votre Tevo Tornado ou Creality CR-10 :
Vous avez besoin de (Il existe une version 12 et 24volt) : http://www.ebay.fr/itm/10-x-24V-24-Volts-BLANC-6-LED-FEUX-DE-GABARIT-CAMION-CARAVANE-SHASSIS-REMORQUES/322314654417
Pour pouvoir installer la pièce dans le rail de la Tevo Tornado, vous devez retirer les vis du rail coté droit. Exercez une légère flexion de la pièce support et tout en tenant la flexion faites la glisser lentement dans le rail, puis relâcher.Vous pouvez ajouter un vis M3-M5 munie d’un T-nut.
Les leds sont branchées en parallèle (12-24v) directement sur l’alimentation (24v pas 110-220v)
Pour que la pièce soit solide, je conseille 90% d’infill.
Low cost led lights in 12-24 v.
You need in (12 or 24v): http://www.ebay.fr/itm/10-x-24V-24-Volts-BLANC-6-LED-FEUX-DE-GABARIT-CAMION-CARAVANE-SHASSIS-REMORQUES/322314654417
To be able to install the part in the TT rail, you must remove the screws from the rail on the right side. Exercise a slight bending of the support piece and while holding the flexion slowly slide it into the rail and then release. You can add a M3-M5 screw fitted with a T-nut.
The leds are connected in parallel (12-24v) directly on the power supply (24v not 110-220v)
For the piece to be solid, I advise 90% infill.
Print Settings
Printer Brand:
TEVO
Printer:
Tornado
Rafts:
No
Supports:
Yes
Resolution:
0.2
Infill:
90 -
Controlpanel for Ikea Lack Graphic Smart LCD Controllerand W1209 3D Print Model
Summary
Controlpanel for ikea lack table for Graphic Smart LCD Controller and W1209 Fancontrol
Its a Extension of thing:87250 and thing:2139389 for Ikea lack -
Antman – Civil War Helmet Wearable 3D Print Model
Summary
its sized and thickend so you only have to cut out the eyeholes. -
Tronxy X5s Z axis printed split bushing 3D Print Model
Summary
When building my Tronxy X5s, I was not impressed by the stock Z axis bearings. So I designed and printed a replacement system. The bushing has a split in it and you slide the sleeve over it and tighten it with 2 M3 screws and nuts. I printed the bushing in PLA and the Sleeve in PETG, but you could print it in PLA. There is also a short version in which a IGUS RJ4JP-01-08 sits on top of it and both are held and tightened by the sleeve. This was created for the people who do not like PLA bushings.
Print Settings
Printer:
SmartRap – Highly modifed
Rafts:
No
Supports:
No
Resolution:
.2
Infill:
30
Notes:
Set up the number of shells to be enough to create the bushing vertical section without any infill. Allowing the shells to make up the “fingers” of the inner part of the bushing. Mine was 3 shells.
How I Designed This
Designed in Fusion 360 -
Royal Talon (“Black Panther” Movie) Free 3D Model
This is T’Challa’s aircraft from the new “Black Panther” movie. It’s not perfect, as I was working entirely from a few screen captures from the movie trailer 🙂 But it’s a good starting point if anyone wants to take it further.
-
One-piece Caliburn Foregrip 3D Print Model
Summary
Remixed from Caliburn (Captain Slug) and user Misery5567 (AR-15 Skeleton Foregrip) -
15mm x 5mm magnet holder 3D Print Model
Summary
15mm x 5mm magnet holder.
The hole for the magnet is a little undersized so the printed part can be heated a little (eg hot water if using PLA) and press fit. Or use some glue or if your magnet has a hole in center – a screw. I went with heating and press fit and its been solid.
i didn’t use any support when printing, the inside roof of the hole where the magnet goes is a fair span (15mm of unsupported distance) and so that particular surface wasn’t perfect but it worked fine and its behind the magnet anyway – doing this saves breaking out support material.
Print Settings
Printer:
aldi cocoon
Rafts:
No
Supports:
No
Resolution:
0.2mm
Infill:
no -
spare fuse holder 6 x 30mm 3D Print Model
Summary
Holds a spare 6x30mm fuse.
Use zip ties to connect it to a lead and you have a spare fuse ready to use for your equipment.
Print Settings
Printer:
aldi cocoon
Rafts:
No
Supports:
No
Resolution:
0.2mm
Infill:
80% -
Rostock Nano Basic Cooler 3D Print Model
Summary
This is a Rostock Nano’s 30mm fan Cooler.
For easy make easy remix.
Fixed fan :M3x20mm x2
Fixed plathome M3×15mm ×1 With Nut
Print Settings
Printer:
Rostock Nano
Rafts:
No
Supports:
No
Resolution:
0.2mm
Infill:
40% -
Customizable Knob! – PGS 3D Print Model
Summary
Modified https://www.thingiverse.com/thing:54024 to include an option to change the orientation of the notch. -
Vase 3D Model
Additional Info: Vase magnolia flowers N291217 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
Locker 3D Model
Additional Info: Locker N150118 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
YETI LoadOut Bucket Gear-Strap-Hook thingy 3D Print Model
Summary
This is a custom strap hook that fits in the bucket slots. I plan on making a custom gear belt for my bucket and this is how I will attach the belt to the bucket. Similar design to the YETI Gear Belt shown here:
https://www.yeti.com/accessories/loadout-gear-belt/23040000019.html -
Piper 1 3D Printer Electronics Enclosures 3D Print Model
Summary
Arduino and Ramps 1.4 (plus optional SSR) and PSU enclosures for Piper 1 3D printer.
To fit this enclosure Ramps 1.4 board need some minor modification: power connection of the board should be resoldered to use Pitch PCB Mount Screw Terminal Block like this: https://www.amazon.com/gp/product/B00FZLPCKC instead of Male-Female PCB Screw Terminal Block.
Link to Piper 1: https://www.thingiverse.com/thing:2794632 -
Quadcopter battery storage 3D Print Model
Summary
A holder for quadcopter batteries, the size of the inner compartment is 25x9x44. In the picture it says 400 mah, I changed it in the design to: “batteries”, so if you have different batteries it’s not the wrong value.
Print Settings
Printer:
TronXY X1
Rafts:
Doesn’t Matter
Supports:
Yes
Resolution:
0.2
Infill:
20
Notes:
the print orientations are correct, you need the print: “Quad_battery_holder_Thingiverse_1” with supports. -
Battlestar Valkyrie 3D Print Model
Summary
Battlestar Valkyrie model pulled from Sins of a Solar Empire mod Fall of Kobol (http://www.moddb.com/mods/fall-of-kobol).
Still working on getting it optimized for printing. -
Tribute to Tiffanys pen holder 3D Print Model
Summary
This was created as a gag gift for some people in the office. It was supposed to resemble the $1000 Tiffany’s sterling silver pen holder.
Best results can be achieved by using primer filler and wet sanding a few times, then painting the model with sterling silver spray paint
The inside of the “can” was painted with Rust-Oleum 284678, Gloss Light Turquoise
Print Settings
Printer:
D-Bot / Anet A8
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
.2mm
Infill:
Doesn’t matter
Notes:
Might want to print the first layer slow to get the best resolution on the text. -
Xhover Win5L SMA + Immortal T Holder 3D Print Model
Summary
Designed a SMA + Immortal T mount for the new Xhover Win5L frame. Same basic design as the one for the Win5, but with the posts adjusted further in. Needs to be printed in TPU in order to get the Immortal T in the hooks.
Print Settings
Printer:
Wanhao Duplicator i3 Plus
Rafts:
Doesn’t Matter
Supports:
Yes
Notes:
Print in TPU -
Konahrik Dragon Priest Mask SLICED 3D Print Model
Summary
I really liked the mask but I only have a 8x8x8 build space so I sliced this guy up in mesh mixer for those in a similar boat. This should work on many more printers now. Print edge down on glass bed with auto supports and it should come out perfect after you glue the edges.
Print Settings
Printer Brand:
TEVO
Printer:
Tornado
Rafts:
Doesn’t Matter
Supports:
Yes
Infill:
30
Notes:
Use brim if printing fast so print doesnt come off bed.
GO TO JTM’S PAGE FOR TUSKS -
Uncle Grandpa Time Machine Watch 3D Print Model
Summary
My son is a fan of the Cartoon Network show Uncle Grandpa. In s03e03 Back to the Library, Uncle Grandpa uses a time machine watch to travel through time. My son wanted one so I made this model and printed him off one. It’s modeled to his size, so scale to what will fit you.
Print Settings
Rafts:
No
Supports:
NoPost-Printing
You’ll need to add a strap to this. Given the size I printed mine at, it requires something custom.
It also requires some blue paint for the recessed triangle and “buttons”. -
Table 3D Model
Additional Info: Table N150118 – 3D model (*.gsm+*.3ds) for interior 3d visualization.
-
full register and buss 3D Print Model
Summary
this is the full register and buss, each register of the processor will use this component.
http://www.imm.org/Reports/rep046.pdf
the scad file also contains the other components that have been uploaded previously.
t.
Eventually i intend to parameterize the file and make it animatable but my current skill level with open scad is rudimentary at best.
