Summary
guitar pick 3 sizes. to be printed with pteg at high rez
Category: 3D Print Models
Premium & 3D Print models ready to be 3d printed. 3D Print Models and Free 3D Print Models are available for download in several formats including .STL, .3DM, .OBJ, .3DS, .DAE, .SKP, .BLEND, .DWG, .DXF, .STEP and much more. If you’re in search of high-quality 3D printed assets, we have a huge library of 3d print models for any of your needs. Also you can visit 3D Models and All 3D Models category.
-
LCD Knob with a thumb sub-knob 3D Print Model
Summary
As for many of us, the knob that came in the kit was not working properly and got lost on the second day (or night, not sure, not enough sleep).
I wanted a small knob, that would allow to quickly change the speed of the print (as I’m twitchy during the night prints, usually worse by 4 am).
I’ve added a finger-tip knob onto the knob, to allow for faster/lazier spinning of the dial.
If it works for you, I’m glad. If it doesn’t, don’t bill me for the fill.
PS: Feel free to adjust the height (Z) of the knob.
Original size was slightly exaggerated in order to accommodate for the bracket of the spool holder, which is a bit too close to the knob. -
Basic Pi 3 Holder 3D Print Model
Summary
Basic case for a Raspberry Pi 3. It doesn’t require screws, and will fit the ribbon cable for the breakout board I use. it has easy access to the SD Card, and Camera Ports. Does not require support. -
Blue Microphones Yeti Shock Mount 3D Print Model
Summary
This is a shock mount I designed for my Blue Yeti microphone. It requires 1/8″ bungee cord for assembly, approximately 1-2M if you want to be safe. Using dabs of hot glue when assembling the arms to the clamps would help with assembly.
NO EXTRA HARDWARE IS REQUIRED. The thumbscrews that are included with the Blue Yeti can be used to mount the clamps to the microphone body, as designed. You don’t need to purchase hardware, just bungee cord.
A mic adapter can be taken off of most mic holders (check model for exact tab width to be sure it’ll fit) if not, those mic holders usually come with boom arms from Amazon. Super easy to get ahold of, especially if you need a boom arm as well.
Print Settings
Printer:
Maker Select Mini V1 Rafts:
Yes Supports:
No Resolution:
0.1mm Infill:
80-100 -
Zebra DelGuard Eraser Cap 3D Print Model
Summary
I designed this piece to replace the eraser cap that came with the pencil after losing it. Fits the Zebra DelGuard 0.7mm pencil.
Post-Printing
Sanding/Other finishing things
Depending on how you use supports when you print this, you may want to sand the surface or use acetone mist to smooth the surface. -
Mashrique Pandent 001 with Earrings 3D Model
Product Code: M-LS 001Weights:Locket: 3.47 (18K)Earrings: 4.64 (18K)Ready for printing.For more information, message me.
-
Mashrique Pandent 001 with Earings 3D Model
Product Code: M-LS 001Weights:Locket: 3.47 (18K)Earrings: 4.64 (18K)Ready for printing.For more information, message me.
-
Phone Holder 3D Print Model
Summary
I shrunk the original down by 75% and added a lip on the back side of the part that the phone sits on for phones that have buttons on the bottom of the phone. The lip allows you to press these buttons without the phone sliding off the back.
Print Settings
Printer Brand:
LulzBot Printer:
TAZ 6 Rafts:
No Supports:
No Infill:
20% -
3D printing parameters demo 3D Print Model
Summary
With this kit you can explain different 3D printing parameters :
Layer height
Perimeters
Infill type and percentage
Support
You have to print several cubes with different parameters and stop printing before top layers, or edit GCODE file and remove top layers lines.
Each stand can be printed in dual color with letters files, or only print the main part if you don’t have a dual head machine.
With DXF files you can lasercut a stand in 5mm plexiglass.
You can edit my design in Onshape here :https://cad.onshape.com/documents/f1a81a355866302737195f45/w/d7db81a4277974cb45024720/e/2828d205cc6bc269c7cdda1e -
Winston from Overwatch 3D Print Model
Summary
My Version of a Winston from Overwatch. It´s not 100% the same as in the game but i have tried to make it as good as possible.
Made with ZBrush, edited with Meshmixer and repaired with Microsoft on-board 3D-Builder.
I sliced him in different pieces to make it easier to print. -
1/4-20 pistol grip 3D Print Model
Summary
1/4-20 pistol grip for camera or other. Others had adjustments on top, and the bolt was near the top. This is recessed in, for an event where you need a MUCH stronger mount for heavy application.
In this case, a steel plate is bolted to this part, and a strong magnet is used to hold devices to it. Needed a lot of strength as commercially available versions were breaking.
I printed at 30 and 50% infill, in ABS. Used Deck screws to mount the mating parts. -
Uno Replacement Box 3D Print Model
Summary
Better Board Game Inserts
Guiding Principles
Board game pieces should stay put no matter the orientation of the box
No Bags!
Use as little filament as possible
Ideally no Supports
The Inserts
This is intended to be a box for storage as well as a convenient way to draw cards. Largely based on the original game design.
Desgin
These were designed using Onshape here.
Print Settings
Printer Brand:
LulzBot Printer:
TAZ 6 Rafts:
No Supports:
No Resolution:
Max layer height ~80% nozzle size Infill:
20% -
Realistic DX-350 Shortwave Radio Battery Door 3D Print Model
Summary
I’ve had this DX-350 radio forever, and I’ve never had a battery door for it, until now!
If you’re reading this, you may be the only other person on earth that still has a DX-350.
I went through 12 versions until I had one that fit tight, went on and off easily, and didn’t interfere with anything under the door. I have no idea what the original looked like, or how it worked, so this could be better or worse. No idea. If yours is also missing altogether, this one is definitely better 🙂
Post-printing break off the small support at the end of the door clip. It’s only .4mm wide and easily pops right off.
To install the door, slip the hinge end in first, then pull the door back with the finger slot to allow the tongue to fit into the slot. I used plain old PLA, and it was plenty flexible. I’ve had it on and off 10x without issue.
Enjoy!
Print Settings
Printer:
Anet A8 Rafts:
No Supports:
No Resolution:
.1mm Infill:
30% or higher -
Model wheels for forklift, etc. 3D Print Model
Summary
Some simple wheels for this forklift:
https://www.thingiverse.com/thing:1694824
Note I scaled it up a bit so you’ll need to scale it to match whatever size you print your forklift at.
Print Settings
Printer:
Creality CR-10S Resolution:
0.06mm -
Anycubic Kossel Back Cable Holder 3D Print Model
Summary
Cable Holder for Delta kossel, prevent jamming cause by cable during printing
using M5 and T nuts M5 -
M3 hex nut knob 3D Print Model
Summary
Knob for hand fastening M3 hex nut
Notice:
Put nut immediately in finished print. -
simplest drinking game 3D Print Model
Summary
Very simple and fun drinking game.
Just make up some rules and begin.
example rules:
arrow: whoever its pointing at
1 point: drink yourself
2 points: choose two who have to drink
A: everybody has to drink
round arrow: waterfall
Print Settings
Rafts:
Doesn’t Matter Supports:
No Resolution:
0,2 -
2020 Caster Mount 3D Print Model
Summary
Inspired by this NYC3D caster mount (https://www.thingiverse.com/thing:2463705) I designed my own due to being unable to source a 28mm screw space caster wheel. This caster mount will work for any 20×20 V-slot extrusions. For the wheels i am sourcing them from Home Depot Everblit line, that makes it a lot easier to get for most people in North America.
When installing the M5 nut it will be a tight fit, use your pliers to push it in.
Additional Hardware required
Low Profile Screws M5 x5http://openbuildspartstore.com/low-profile-screws-m5/
M5 Nut x4
M5 T-Nut x1http://openbuildspartstore.com/tee-nuts-25-pack/
Everblit 2″ caster wheelhttps://www.homedepot.ca/en/home/p.2-inch-swivel-medium-duty-castor-with-88-lb-load-rating.1000784517.html
Print Settings
Printer Brand:
MakerBot Printer:
MakerBot Replicator 2 Rafts:
No Supports:
No Resolution:
.2mm Infill:
30% Notes:
Print -
Spray can holder for 55mm cans 3D Print Model
Summary
Just a simple can holder for a can smaller than 55mm in diameter. We mountain bike and during the summer, bug repellent spray is mandatory, so we keep a can in the car. Problem is there’s no good spot for it and so it winds up rolling around the car, so I designed this simple holder to be mounted on the side of the cargo area using double-sided tape.
Print Settings
Printer:
Monoprice Maker Ultimate Rafts:
No Supports:
No Resolution:
0.2mm Infill:
20% lines Notes:
Simple print, no raft or support needed, I printed in ABS only because that’s what I had loaded in the printer. Printed with three shells. -
BSG Original Cylon Raider in parts 3D Print Model
Summary
Original Cylon Raider remixed from: https://www.thingiverse.com/thing:291123
Chopped up for cleaner prints and some minor cleanup on gun barrels and body. The model has hollow areas in some places and I cleaned up a few.
With 25% infill or more on the main body, it comes out fine except the bottom doors which you can rip off after printing. Thay may print better at larger sizes.
Print Settings
Notes:
Print the main body with supports!!! Infill at 25% or more. You will have to clean up bad sections in the engine output and the bottom doors.
Wings: 25% or more
Guns 25%
Barrels: Solid. Print standing up for best results. -
Huevo sorpresa 3D Print Model
Summary
Deben voltear la pieza inferior al imprimirla
Print Settings
Printer:
Flyingbear p905X Rafts:
No Supports:
No Resolution:
0.2mm Infill:
20% Notes:
Revise muchos huevos en este sitio, pero ninguno que pudiera servir para mi hijo de 2 años.
Por lo que después de leer, estudiar un poco, hice mi propia versión.
Hecho en PETG.
235º y 60º -
Ring Bearing 3D Print Model
Summary
If you print this model please upload a “make” so I can see your results.
This is a test of print settings. Good luck! -
Tevo Little Monster Clip-On Cable Fenders 3D Print Model
Summary
Tonight when I was calibrating my Little Monster I heard that awful sound when the cable gets stuck between the truck and the optical sensor… It’s probably the 20th time it’s happened but this time I said enough is enough!
So I made these cable guards that only take 10 minutes to print and they snap into position and won’t budge unless you want them to – they work a treat! 🙂
Print in vase mode in the supplied orientation
You can check out my other designs here:-https://www.thingiverse.com/ScottyMakesStuff/designs
You can see all my videos on my YouTube Channel, ScottyMakesStuff here:-https://www.youtube.com/c/ScottyMakesStuffhttps://twitter.com/ScottyMakesStufhttps://www.instagram.com/scottymakesstuff/ -
S800 Sky Shadow improved servo horn 3D Print Model
Summary
Just a small little servo horn with around the same distances than the original that comes with the kit. The problem with the original one was that the horn has to be placed directly through the carbon rod in the control surface. My version should fix that and has a spare space for the carbon rod to go between the servo horn fixture.
At the moment untested, I will update if I have the time to build my S800 😉
Print Settings
Printer:
Tevo Tarantula Rafts:
Doesn’t Matter Supports:
No Resolution:
0.1 Infill:
100% Notes:
Just print it with 100% infill and with high resolution for better results
Post-Printing
I did draw it without tolerances, so you maybe have to widen the holes of the two plates.
And also drill the holes that you need for the linkage 😉 -
welding gun 3D Print Model
Summary
this is a simple welding gun that i made by myself. if you have any tips on how to make it better than please tell me. -
Threaded Rod Ends for Ferrari Part #61326200 3D Print Model
Summary
Left and right threaded rod ends for assembly 61326200 -
Feather 3D Model
High poly feather.File contains one printable mesh object.Measure units are meters. The feather is about 15 cm in length.Available formats: .blend, .fbx, .stl, .obj, 3dsFaces count: 502688.For .3ds format there is only 60322 faces.
-
dyson v8 adapter 3D Print Model
Summary
A adapter for old dyson accessory ，now you can mount them to the v8 vacuum cleaner
-
Dropcam Pro Window Mount 3D Print Model
Summary
This is a Dropcam Pro window mount based on the window mount by robcurtis, however, I remixed it to eliminate the blind-spots (in the corners of the video) caused by the original design’s round aperture. I also added two additional holes, which I can only assume are present for drainage of any moisture/humidity that may build-up within the mount once it’s on the window. This design holds the camera at a 15-degree angle to the window, just as the original design.
Print Settings
Printer:
Creality CR-10 Rafts:
No Supports:
No Resolution:
0.1-0.2 Infill:
25% Notes:
I printed this using a 10mm brim because of the rather narrow bed contact area, but it could probably be printed as-is if you have good bed adhesion. Otherwise, no supports are needed and anything from 20%-25% infill will provide plenty of structure and strength. -
Iron Man Gantry System 3D Print Model
Summary
I found the source of this model over on 3D Warehouse and have made revisions to it.
https://3dwarehouse.sketchup.com/model/49b7e04b997ee7fb551e7d48442dc728/Suit-up-Gantry
I wanted to print one for an action figure but the model wasn’t quite ready for printing. I filled in some of the spaces in the original model to make this printable. I used SketchUp and elements the designer provided. -
“algo” card case 3D Print Model
Summary
This is a card case for “algo”. “algo” is a famous math card game in Japan. I created a case to carry only the card.
Print Settings
Printer:
HyperCube TS1 Rafts:
No Supports:
No Resolution:
0.2mm Infill:
25% -
Anycubic I3 Mega X axis Fan stepper fan mount with heat sink clearance 3D Print Model
Summary
Friction fit fan mount with air channels and clearance for 40mm heat sink stuck on the end of Z axis stepper. Mounting holes designed for 40mm fan. Print with mount side down. There are minimal supports needed.
Print Settings
Printer:
Anycubic I3 Mega Rafts:
Yes Supports:
Yes Resolution:
0.2 Infill:
20
Post-Printing -
scx10 fuel tank mount 3D Print Model
Summary
I made this after moving my battery to the front and realizing there wasn’t really a place for my esc. It slides between the frame rail and uses the lwb holes that are already in the chassis and 2 m3 screws. It will not work with a lwb scx10. -
Mastercrafted Wolven Silver Sword – The Witcher 3D Print Model
Summary
Every budding Witcher needs their trusty twin swords, and here we have the Mastercrafted Wolven Silver sword from the Witcher 3. (Steel available at https://www.thingiverse.com/thing:2761042)
Being scaled to the lore and the game files, the hilt is just over 12″ long, and the blade a further 38″. A pair of holes are present down the blade in order to house two 2.5 x 1m long carbon fibre cores and keep everything together. These are designed to poke slightly out of the blade and into the hilt for truer centering. A second hole also runs down the length of the hilt and into the blade in order to contain a 1/8″ x 3/8″ steel core.
The grip is designed so that you can wrap a 3mm thick leather cord around them and have a true look to the game designs.
The runes read “One made of silver” / “for creatures” as a callback to an in-game quote, as well as “Valentine Costumes” (my cosplay brand) – if you wish I am willing to customise this file with your own text or different runes (price dependant on changes) – please feel free to contact me if you’re interested in this service.
Due to common transportation issues with large blades such as this, it is designed to come apart where the blade and hilt meet. If you attach the hilt to the aforementioned metal core, you can then drill a 5mm hole in the core at the point where a hole features in the top of the blade (Blade_2 file), and then use a 5mm binding screw to hold it all together.
Please feel free to use / modify this model as you wish, but credit is always appreciated.
Now get out there and kill some monsters
Print Settings
Notes:
Supports only necessary on the pommel, but possibly advised on the grips also -
Tool for mounting of furniture door 3D Print Model
Summary
petg
Print Settings
Rafts:
Yes Supports:
Yes Resolution:
0,2 Infill:
50 -
Creality Ender 4 strain relief 3D Print Model
Summary
I wanted a strain relief bracket which didn’t interfere with the bed levelling screws – instead, one that clamped the bed carriage would be ideal using m3 hardware
The one I made is v1. This is version 2, featuring an angle to avoid screws contacting the bed, nut retainer insets and slightly narrowed. I reduced the diameter of the cable channel to get a tighter cinch with the cable ties.
To complete, use two m3 10mm or 12mm bolts and nuts to clamp the carriage, and two small cable ties, just push them through.
Print Settings
Printer:
Creality Ender 4 Rafts:
No Supports:
Doesn’t Matter Resolution:
0.32mm Infill:
20 Notes:
To print, rotate onto its side, it shouldn’t need supports though a brim may help. If using PLA, print it slightly hotter than normal (PLA+ settings) to increase interlayer bonding. Printed 215-220 deg C to increase strength.
Infill doesn’t really matter, 3 perimeters / 1.2mm wall is what I used, it’s more than enough.
How I Designed This
Designed in Onshape from scratch, if you want to edit it the link is here:https://cad.onshape.com/documents/2d61c918ed37344b6f5f4652/w/5cc150713efcf0918f92af5e/e/7c914fb3f0feff55238d9b94 -
Pen Plotter 3D Print Model
Summary
This is an attachment made to turn your 3D printer into a 2D pen plotter. The bracket simply bolts onto the bottom right corner of the hot end fan. I designed this pen plotter so that it fits around a radial fang mount. A 5mm bolt is used to hold the pen in place and a lock nut can be press fit in the inside of the pen hole. The bracket is capable of holding pens up to the size of a typical sharpie. I have attached the STL, along with the solidworks part file incase anyone wants to remix this part. -
The Orthodox Order Parthenius pontiff of Ananievsky 3D Model
The Order consists of two parts. The real size. Stones and enamels are shown only for visualization.
-
Baguette decorative 3D Model
Decorative baguette in five different variants. The baguette can be applied in any directions, it is suitable for interior finishing (walls, the corners, edges, transitions from one finish to another and also for designers. For the manufacture of designer items.In this Assembly represented:1) Colorless baguette – corners 2 PCs 10×7.01х15см. interior and exterior, 1 video 50х7.01.х15см., Video 1 1 meter long.2) Desert baguette – Assembly video with parts of the deposited structure.3) iceberg baguette – only video 50х7.01х1.5, marked texture4) Aqua baguette – only video 50х7.01х1.5, marked texture5) Cocoa tree – straight 50s.7.01х1.5, 2 10×7 area.01х1.5 inner and outerAll files in one file and ready to print.Formats: .obj .3mfP . S .All textures similar to continue (merge at the junction is so invisible seams when you connect one figure with another figure) very well when doing repairs and it is necessary to close the long distance of over 3-5 meters in length.
-
Skull 3D Model
Skull on a fan or cooler. Sizes and colors can be configured at your discretion. The model is ready to print.
-
Stylish pendants 13 pieces 3D Model
Stylish pendants 13 pieces – beautiful pendants which will delight the eye and lift the mood. All pendants can be adjusted in size before printing, you can change colors and textures. In set 2 option 13 pieces of 1 option with textures and option 2 without the textures and coloring (empty). Both ready to print. File formats object .obj .3mf .mtl
-
A set of hangers consists of 13 pieces 3D Model
A set of hangers consists of 13 pieces – beautiful pendants which will delight the eye and lift the mood. All pendants can be adjusted in size before printing, you can change colors and textures. In set 2 option 13 pieces of 1 option with textures and option 2 without the textures and coloring (empty). Both ready to print. File formats object .obj .3mf .mtl
-
dino shoes 3D Print Model
Summary
i creates this for my 5-year old’s crazy shoe day.. they are remixed from the original t-rex skeleton by makerbot
Print Settings
Printer:
corexy Rafts:
No Supports:
Yes Resolution:
.25 Infill:
20% Notes:
you need to use supports in s3d as they are easy to break away. 0.1 resolution will be best but 0.25 is also fine.
the skulls are attached to the shoe using either string or hot glue
