Summary
This is the housing of an IEC C20 male connector.
Needed a new one cause I managed to break one.
Category: 3D Print Models
Premium & 3D Print models ready to be 3d printed. 3D Print Models and Free 3D Print Models are available for download in several formats including .STL, .3DM, .OBJ, .3DS, .DAE, .SKP, .BLEND, .DWG, .DXF, .STEP and much more. If you’re in search of high-quality 3D printed assets, we have a huge library of 3d print models for any of your needs. Also you can visit 3D Models and All 3D Models category.
-
IEC C20 connector housing 3D Print Model
-
Francesca Magic Wand 3D Print Model
Summary
[Più sotto il testo in italiano]
This is the magic wand I made for my daughter Francesca; starting from Patrick Mahoney’s project, (https://www.thingiverse.com/Patrick_Mahoney/about) I wanted to make it happen too but I had several problems so I finally re engineered everything.
The handle is made in 2 parts, cut asymmetrically for convenience, contains the useful space for 2 AAA batteries a scar for the wire of the negative pole and a hole for the same as well as a hole for the positive pole in the central area.
I attached STL both integer and sectioned as interesting to me.
As in Patrick’s project I use an LED (in my case 3mm white 3v) and an inertial switch that is OFF when horizontal. Minimum cost.
The thin part is a single piece and long with an embroidery similar to the handle, the lower part penetrates into the handle and is also a container for the vertical sensor.
The pieces were printed in ASA all without supports, the handle horizontally in two parts while the thin vertical part with a lot of brim to support it being very tall but thin.
Questa è la bacchetta magica che ho realizzato per mia figlia Francesca; partito dal progetto di Patrick Mahoney, ( https://www.thingiverse.com/Patrick_Mahoney/about) volevo realizzarla anche io ma ho avuto diversi problemi quindi ho infine re ingegnerizzato tutto.
Il manico è realizzato in 2 parti, tagliato in maniera asimmetrica per comodità, contiene lo spazio utile per 2 batterie AAA un incavo per il filo del polo negativo e un passante per lo stesso oltre ad un passante per il polo positivo in zona centrale.
Allego STL sia intero che sezionato come interessava a me.
Come nel progetto di Patrick uso un led (nel mio caso bianco 3mm da 3v) ed un’interruttore inerziale che in pratica è OFF quando orizzontale. Costo minimo.
La parte sottile è un pezzo unico e lungo con un ricamo simile al manico, la parte inferiore penetra nel manico ed è anche contenitore per il sensore di verticale.
I pezzi sono stati stampati in ASA tutti senza supporti, il manico in orizzontale in due parti mentre la parte sottile in verticale con molto brim per sostenerlo essendo molto alto ma sottile.
Print Settings
Printer:
Anycubic Delta Kossel Plus Rafts:
No Supports:
No Resolution:
0.2 Infill:
20% Notes:
some brim for the thin part printed verticallyCustom Section
-
Footballer 02 Flipstrike 01 Stl 3D Model
Footballer 02 Flipstrike 01 STL 3D print model3d printable model of the footballer similar to Ronaldo player.Model has near 180mm height.2 Millions 3mf checked for errors and repared.10 Millions obj included and can be used to add some details.See details in netfabb analisys preview picture.Not for macro renders
-
Kwiwk Koin 3D Print Model
Summary
My personal logo as a 3D coin. -
1/24 V2 (IMPROVED) Twin Motor mount/center skid/box ECX RGT FTX Barrage 3D Print Model
Summary
This is V2. I rotated the motors 90 degrees and moved them closer to center. I also raised them .050″. Now there is much better link clearance.
This is to mount two gear reduction motors in an ecx barrage or like rc crawler. Greatly slows it down for much more controlled crawling. Big improvement over stock. You have to either shorten the drive shafts or motor shafts slightly. Also you need to shave the links that mount under the motors. Uses factory hardware. No need to use screws to mount the motors. I used 300rpm motors. You can use the factory esc. Also you have to switch polarity on one of the motors. I’m thinking a higher rpm motor will be better for wheel speed. I’ll be experimenting with thathttps://www.amazon.com/Yosoo-Reduction-300RPM-Gearbox-Replacement/dp/B01C6MGK7G/ref=sr_1_7?ie=UTF8&qid=1517122153&sr=8-7&keywords=gear+reduction+motor -
FORTNITE Bookmark 3D Print Model
Summary
Bookmark for fans of FORTNITE. Painted to help show some detail.
Print Settings
Printer:
Flux Delta Rafts:
No Supports:
No Resolution:
Medium Infill:
No Notes:
Sized to 75%. -
SFIC Holder 3D Print Model
Summary
An M2.5 screw and nut can be inserted and used as a set screw to hold the lock firmly in place. This is an ergonomic adapter to make holding SFIC cylinders more comfortable while picking. This will allow the control lug to be sticking out and still fit inside the enclosure. Partially hollow through and through to reduce filament and give you access to the rear of the plug.
This is a theoretical model as I do not currently have an SFIC cylinder on-hand to test with.
Print Settings
Rafts:
No Supports:
No Resolution:
.2 Infill:
15 -
Bas-relief of the Indian 3D Model
3d model bas-relief of the Indian. It was created for printing on a 3d printer
-
Lotus Flower figurine 3D Model
3d figure of a flower. The model was created for printing on a 3d printer
-
A set of fractal three-dimensional monochrome symbolic objects 3D Model
A set of fractal three-dimensional monochrome symbolic objects. 4 spheres created for printing on a 3d printer
-
Mephiles the Dark Sonic X 3D Model
3d model of Mephiles the Dark Sonic x. It was created for printing on a 3d printer, it has a detachable stand
-
Blade Runner 2049 Memory Sphere Holder 3D Print Model
Summary
Two models for 30mm memory spheres, One with symbols and one without on the handle, If anyone needs larger sizes I can edit, or you can simply upscale.
Print Settings
Printer:
Anet A8 Supports:
Yes Notes:
I would recommend the supports under then handle. I tried both ways and this gave me the cleanest print.
Post-Printing
Sand it smooth and give it some silver paint! -
Anycubic I3 Mega Digital Dial support 3D Print Model
Summary
A remix between 2 great designs.
ltlowe design was too short, x9x9x9x9x9 was for a different dial…
Will soon post a photo of the real deal.
Print Settings
Printer:
Anycubic I3 Mega Rafts:
Doesn’t Matter Supports:
Yes Resolution:
.28 Infill:
10 Notes:
Just print 🙂 -
Hex Wrench 3D Print Model
Summary
At 100% size, this is a 10 mm hex wrench. To get other sizes, just increase or decrease the size of the wrench in your slicing sofware. For example: if you need a 6 mm hex wrench, print at 60% size. If you’re printing in PLA, make the 3D model a tiny bit bigger because PLA tends to shrink when cooled. So if you are printing the 10 mm hex wrench in PLA, print it at 100,3% size or bigger, depending on your printer’s settings.
How I Designed This
In Fusion 360 -
G18C SAI slide for AEP 3D Print Model
Summary
G18C SAI AEP silde for Cyma .030 or TM G18C. This might need some filing and modifications to fit. Please let me know if you print it, and how well it fits. -
Snow Wheels for R/C Buggy – Rear 3D Print Model
Summary
After making wheels I hoped would be suitable for hard/bare ice on a frozen lake, it snowed, and there was no more bare ice, so I made these “snow” paddle wheels (which would probably work okay in sand too). Customize and enjoy!
Front wheels for a 2WD that would complement these: https://www.thingiverse.com/thing:2760889
Note: These probably should be printed in ABS or PET-G to avoid melting if you’re planning to use them in hot sand.
Note: To make a matching wheel, just mirror this one in the slicer. -
Footballer 02 Flipstrike 02 STL 3D Model
Footballer 02 Flipstrike 02 STL 3D print model3d printable model of the footballer similar to Ronaldo player.Model has near 180mm height.2 Millions 3mf checked for errors and repared.10 Millions obj included and can be used to add some details.See details in netfabb analisys preview picture.Not for macro renders
-
Filament Cooler Fan Shroud, Dual Side, E3D Chimera and Cyclops 3D Print Model
Summary
Dual side shroud designed for lightness, access, and easy installation on a E3D Chimera or Cyclops hotend.
Printed with PETG, standing on fan mount surface.
Print Settings
Printer:
Banana 3D 330 Rafts:
Yes Supports:
No Resolution:
<= 0.2 Infill:
70 to 100% Notes:
Instead of a raft, a brim may be used with good results.
Heater block “socks” provided by E3D with their chimera and cyclops extruders should be used to minimize heat loss from peripheral air flow. -
Vertex3 LED Race Fin 3D Print Model
Summary
This is designed to have a sections of LED’s glued to the inside of the print giving it a nice illuminated look. One could also use clear TPU and utilize the RGB control form the flight controller.
More information about the Vertex frame here: https://www.cnbracing.com/backpacks
Print Settings
Printer:
Hictop Rafts:
No Supports:
Doesn’t Matter Resolution:
0.2mm Infill:
100% -
CTC Prusa i3 fan adapter 3D Print Model
Summary
This adapts the https://www.thingiverse.com/thing:1161013 to a CTC prusa -
Camera_holder_1/4_hole 3D Print Model
Summary
This is a redesign to fit a 1/4 bolt
This fits the camera arms by coberdashttps://www.thingiverse.com/thing:306091
Print Settings
Printer:
CTC 3d printer Rafts:
No Supports:
No Infill:
25 Notes:
ABS -
Cat yoga 3D Model
The size of the figurine is 115 * 55 mm.Model for 3D printing, printing from two mirror halves.The inner part is made with a small cavity.
-
WATER POWERED – LED FLASHLIGHT Free 3D Model
I’ll Show You – How deliver electric power in alternative ways… Free Geen Energy without poison or toxinsI named this MEDELIS BATTERYThis battery generates electric power out of Tap Water (drinking water, river,lake,rain or any similar liquid)…its small, powerful and super basicMEDELIS BATTERY will generates electricity until the water dries up…for many hours (you can always refill water – make it work again)if you do not let water to dried (put it all in a plastic bag) battery will generates electric power for very long, long….long timeTo make LED-Flashlight you will need some stuffs…LED 5mm, Copper Wire, Magnesium Ribbon & Cotton Wipes…(MAKEUP REMOVER WIPES)for more info watch my vids… https://youtu.be/w0Dg78SIsTw
-
Ring K1003N108 size 8 EU 3D Model
Ring K1003N108 from collection K1XXX.Possibility of changing the ring dimension once for free.
-
Ring K1004N108 3D Model
Ring K1004N108 from collection K1XXX.Possibility of changing the ring dimension once for free.
-
Ring K1002N108 3D Model
Ring K1002N108 from collection K1XXX.Possibility of changing the ring dimension once for free.
-
Coaster Stand 3D Print Model
Summary
Ständer für die jeweiligen Untersetzer
bisher nicht gedruckt, sollte aber 10 Untersetzer aufnehmen -
Mad catz RAT 1 3D Print Model
Summary
A very interesting project for a friend mouse ! The back part of the Mouse was too light, so I added a coin rack to have more weight.
It’s 1 cents of Euros (https://en.wikipedia.org/wiki/1_cent_euro_coin).
Enjoy, tell me if you use it, I would be honored.
Print Settings
Printer Brand:
Prusa Printer:
Prusa Clone Rafts:
No Supports:
No Resolution:
0.2 Infill:
20-25 -
QuickConnector cap 3D Print Model
Summary
Two versions of a simple cap, with and without eye, for quick connectors used with pee valves in dry suits.
Print Settings
Rafts:
Doesn’t Matter Supports:
No Resolution:
0.2 mm Infill:
solid -
30mm Calibration cube for SLA printers – Hollow 3D Print Model
Summary
This is a hollow cube with drain holes to minimise suction. Stick it on some supports, print it and measure
When I used this on my Moai with v1.15 firmware, using “m” as the relevant cube measurement, the formula to calculate what put in the relevant X or Y entry is:
900*(30/m)
I haven’t used it on my D7 yest, but I’m sure you can work out what formula you would need to use. -
Honeycombs 3D Print Model
Summary
Honeycomb like designs based off of an inputted image. The attached OpenSCAD script just needs a 2d array named “data” declared to work. This array is built by using the python script within the GitHub repo that takes in an image, converts it to grayscale, scales it, and spits out data based off of various options.
Also, be sure to export from OpenSCAD as AMF and not STL to avoid getting broken edges.
View the GitHub page for more: https://github.com/sluebbert/honeycombs -
Datsun 260Z 280Z coin holder 3D Print Model
Summary
On most of our old Datsun Z cars there is an unused spot in the console on the far right. We designed a coin holder to fit exactly in there. We sized it to be able to hold 22 US Quarters. -
Small Screw Container 3D Print Model
Summary
has 34 varring size slots and solidworks file is included so you can edit. -
Anycubic Kossel Heated Bed Mounts 3D Print Model
Summary
I had trouble for whatever reason with the original not being able to be tightened. I removed the slot groove to allow it to tighten and adjust twist as well as adding a hold-down feature.
Print Settings
Printer:
Anycubic Kossel Rafts:
No Supports:
Yes Resolution:
.2 Infill:
100% -
Folding rule holder for IKEA Skadis 3D Print Model
Summary
Simple holder for folding rule, fits IKEA Skadis.
I decided to cut this in two pieces and glue together after printing because then you only need a tiny bit of supports for the hooks.
Print Settings
Printer:
Tevo Tornado Rafts:
Doesn’t Matter Supports:
Yes Resolution:
0,2mm Infill:
10% Notes:
The two parts have to be glued together after printing. -
Mount for Celluon Pico Pro Projector 3D Print Model
Summary
This a mount for the Celluon Pico Pro Projector. Add this to your 3D-model to attach the projector to it.
Print Settings
Printer:
MP Select Mini Rafts:
No Supports:
No Resolution:
0.2 Infill:
0-100% -
Patchwork Insert 3D Print Model
Summary
This is a simple insert for the game patchwork. The money tray pops out and can be placed on the table. -
stickers For motors and End stop, Fan0 – Fan1 3D Print Model
Summary
stickers for motors and end stop -
Coffe grinder adapter 3D Print Model
Summary
NOTE: This file is far from perfect, make sure you got the right measurments on the .stl before printing!
To grind coffe directly into the pressure cup. -
Elephant Bank 3D Print Model
Summary
Remixed this as a piggy (elephant) bank. Printing 10 of these for use as a centerpiece at a baby shower -
Bison latifrons skull 3D Print Model
Summary
This scan, performed by the Idaho Virtualization Lab of the Idaho Museum of Natural History, is of an ancient Bison latifrons skull owned by the Bureau of Reclamation. This cranium and horn cores is named Mary Lou. It was scanned at life-size, so please reduce (to between 5-6%) when 3D printing.
The specimen, owned by the Bureau of Reclamation, was part of a larger Bison latifrons 3D scanning project to bring fossils to the public virtually.
For more information, please visit http://virtual.imnh.isu.edu/BoR. -
BOLT Blackops V2 Go Pro Session Mount 3D Print Model
Summary
GP Mount for the Bolt Blackops V2.
We suggest using (countersunk) washers on all four mounts.
Please change the front screws to something longer, circa 14-16mm.
The rear screws, use nylon nuts or drill the holes out to M4.5 and use inset nuts.
Thanks -
Reinhardt Beer Stein 3D Print Model
Summary
I made this because someone who is better at 3d programs then me made a replica of the in game spray and it looked amazing. He didnt list his 3d file nor is he posting his 3d file for purchase. He is only selling the final 3d printed mug for an absorbent amount of money and I hate every part of that.
I want everyone like me to have to the chance to print this because of just how kool it is but couldnt cause the original guy wouldnt post it. If you google reinhardt stein his post is on imgur along side mine now.
Its free and I hope everyone out there who was looking for it can enjoy this. -
Pendant World of Tanks 3D Model
Pendant on the game theme World of TanksModel is ready for prototyping on CNC and 3D Printing.Metal Weight:Gold 24k – 7.6 grams.Gold 18k – 6.15 grams.Gold 14k – 5.3 grams.Silver 925 – 4.1 grams.Triangles – 79602Vertices – 238806Check out my other products by clicking on the name “Alystar” above.
-
Moon Lamp 3D Print Model
Summary
This is a moon lamp that have both surface and glowing details.
Please find more detail at instructables:https://www.instructables.com/id/Print-Your-Own-Moon/ -
Hearts for the Interweb 3D Print Model
Summary
I created this to practice my Fusion360 skill. I have never printed this, so I do not know how well it prints.
At time of this posting, I’ve been creating something in Fusion360 EVERYDAY for 11 days now. If you’re interested you could follow me on Facebook:https://www.facebook.com/HariMakes/
PS: Thanks to Darryl May for the inspiration.
How I Designed ThisTraced an image from the Interweb
Turn it into a repeatable pattern
Extrude it…
Repeat as rectangular pattern.
Add frame. Tada!
-
Rocky Balboa Heavyweight Championship Belt 3D Print Model
Summary
made from pictures… not perfect but it makes the trick.
I used a french flag and some thread…. -
Yamaha XT chain guide 3D Print Model
Summary
The Original was broken and I couldn’t found a new one. So I create this thing.
Print Settings
Printer:
Anet A8 Rafts:
Yes Supports:
Yes Resolution:
0.2
