Download Free 3D Model Tevo Tarantula Power Supply Enclosure 3D Print Model

Summary
Designed to enclose the standard PSU outputs and fit a power meter.
The walls are only ~2mm thick, which make them fragile. This is due to my concern of using less material as possible.
I’ve used XT90 for 2 outputs, it’s oversized but I already had them 🙂
There is an “XT90 Holder” that you can screw on top of them with an M4 screw, but I didn’t needed it.
Fusion 360 file attached, feel free to modify/use it !
Parts needed :
1 Power Socket W/Fuse & Switch :https://fr.aliexpress.com/item/Free-Shipping-power-socket/476915963.html
1 Power Meter :https://fr.aliexpress.com/item/AC-80-260V-LCD-Digital-100A-Volt-Watt-Power-Meter-Ammeter-Voltmeter-110V-220V-free-shipping/32617343719.html
1 meter Black & Red 13AWG:https://fr.aliexpress.com/item/1meter-Black-1meter-Red-Silicon-Wire-Heatproof-Soft-Silicone-Silica-Gel-Wire-Cable-12AWG-13AWG-14AWG/32797523458.html
1 IEC 320 C13 Female Plug :https://fr.aliexpress.com/item/New-Wholesale-Price-Black-IEC-320-C13-Female-Plug-Rewirable-Power-Connector-3pin-Socket-10A-250V/32808416783.html
2 XT 90 :https://www.aliexpress.com/item/5Pair-XT90-XT-90-Gold-Plated-Banana-Plugs-Male-and-Female-Antiskid-for-helicopter-Battery-esc/32460919234.html
2 Banana Plugs :https://fr.aliexpress.com/item/4Pcs-Lot-Speaker-Amplifier-Terminal-Binding-Post-4mm-Banana-Plug-Socket-Female-Connector-10pcs-lot/32739527467.html
Hardware
Terminals Connectors :https://fr.aliexpress.com/item/280Pcs-Assorted-Insulated-Spade-Crimp-Terminal-Electrical-Wire-Connector-Set-Red-Blue-Yellow/32810002612.html
6 Ring connectors #4 Blue
3 Ring connectors #4 Red
5 Female Spade Connector Red
Screws :
4 3×10 (front pannel)
1 M4x10 (side)
Schrink tubes :https://www.aliexpress.com/item/385pcs-heat-shrinking-tube-2-1-Shrinkage-ratio-black/32662765147.html
Print Settings
Printer:
Tevo Tarantula Rafts:
No Supports:
No Resolution:
0.2mm Infill:
20% Notes:
I’ve put a picture of the orientation that I used to print the top part (rotate 145°) to minimise bridging, but it’s not the only way to print it 🙂
For the front panel, I changed filament color manually at the beginning of the 3rd layer.There is a plug-in for Cura to do this and also a way to do it for S3D users… or leave it the same color 😉
Post-Printing
Parts needed
1 Power Socket W/Fuse & Switch :https://fr.aliexpress.com/item/Free-Shipping-power-socket/476915963.html1 Power Meter :https://fr.aliexpress.com/item/AC-80-260V-LCD-Digital-100A-Volt-Watt-Power-Meter-Ammeter-Voltmeter-110V-220V-free-shipping/32617343719.html1 meter Black & Red 13AWG :https://fr.aliexpress.com/item/1meter-Black-1meter-Red-Silicon-Wire-Heatproof-Soft-Silicone-Silica-Gel-Wire-Cable-12AWG-13AWG-14AWG/32797523458.html1 IEC 320 C13 Female Plug :https://fr.aliexpress.com/item/New-Wholesale-Price-Black-IEC-320-C13-Female-Plug-Rewirable-Power-Connector-3pin-Socket-10A-250V/32808416783.html2 XT 90 :https://www.aliexpress.com/item/5Pair-XT90-XT-90-Gold-Plated-Banana-Plugs-Male-and-Female-Antiskid-for-helicopter-Battery-esc/32460919234.html2 Banana Plugs :https://fr.aliexpress.com/item/4Pcs-Lot-Speaker-Amplifier-Terminal-Binding-Post-4mm-Banana-Plug-Socket-Female-Connector-10pcs-lot/32739527467.html
Hardware

Terminals Connectors :
6 Ring connectors #4 Blue
3 Ring connectors #4 Red
5 Female Spade Connector RedSchrink tubes.
Screws :4 3×10 (front pannel)
1 M4x10 (side)