Summary
Just a replacement door stopper for a Vanagon T3. Print it in flexible filament.
Included is the STL file and 123D Design file.
Tag: Replacement
-
Replacement Door Stopper for VW Vanagon T3 Westfalia 3D Print Model
-
Rumble or Frenzy hip replacement 3D Print Model
Summary
Transformers G1 Frenzy or Rumble cassette hip replacement. .2mm, no supports, 100% infill (if that even matters due to size) some sanding may be required depending on condition of hip/leg areas. Happy to report Frenzy has recovered from his hip surgery and is back in the fight! -
Replacement Knob for Nissan Pathfinder 3D Print Model
Summary
Modeled this for a co-worker who needed a couple replacement knobs for his Nissan Pathfinder.
Print Settings
Printer Brand:
Wanhao
Printer:
Wanhao Duplicator i3 Plus
Rafts:
No
Supports:
No
Resolution:
0.2mm
Infill:
20% -
Replacement Cover for Anchor-Hocking 2qt Pitcher 3D Print Model
Summary
The pitcher: a 2 quart container with circular 670mm filler opening. Purchased at Target; Made by Anchor-Hocking.
The original cover/lid got destroyed in the dishwasher, so I created a replacement for it.
I used Inland PLA from Micro Center.
No Photos available as of this entry.
Print Settings
Printer Brand:
PowerSpec
Printer:
Duplicator I3 PLUS
Rafts:
No
Supports:
No
Resolution:
0.08mm Layer, 0.8 Shell
Infill:
100%, 4% Overlap, Solid Top & Bottom
Notes:
All pieces oriented for no support, uses built-in skirt of 8laps.
Post-Printing
Construction
Pieces require only minimal cleaning.
Adhesive used: Gorilla Brush&Nozzle Super Glue.
Adhere 2 blocks to main lid body; let set.
Adhere large hinge block to spout cover; let set.
Using section of 1.75mm PLA filament for hinge, slide ‘hinge pin’ through openings, then glue at outer ends to lock in place.
How I Designed This
Designed in Blender.
All parts have been ‘cleaned’ and ‘prepped’ using the Blender Add-on “3D Printing”. -
Swarmlord replacement teeth 3D Print Model
Summary
snapped some of the teeth off my swarmlord when trying to remove the supports in the mouth
so instead of having a pirate swarmlord, I reinforced the teeth, added some gap filler bits so they print all one piece. (top jaw, bottom jaw)
lay it flat and print it at the smallest resolution your printer can do.
this remix isnt needed if you are printing the swarmlord at 1/1 tabletop scale but i’m scaling mine up quite a bit so the teeth start to get fiddly. -
Medline The Platinum Reacher Clamp Replacement Part 3D Print Model
Summary
Replacement grabber clamp. I made this with 50% fill but if you need it stronger use 75% or more.
Print Settings
Printer Brand:
FlashForge
Printer:
Finder
Rafts:
No
Supports:
Yes
Resolution:
Normal
Infill:
50% -
Logitech G930 U replacement for speaker 3D Print Model
Summary
Hi!
Just recently broke the speaker of on my G930 so i made a new one, Dosent look good but it works.
I printed the U shape with 0,2 res with a 0,4 nozzle.
The locking mechanism is printed with 0,125 res with 0,25 nozzle.
Will probably work to print both parts in 0,2 res with 0,4 nozzle.
I dont know but i think it will also work on the G35 headset.
What u need:
2x M2 16mm long screws
2x m2 Nuts
soldering iron
Print Settings
Printer Brand:
TEVO
Printer:
Tarantula
Rafts:
No
Supports:
Yes
Resolution:
0,125
Infill:
80-100
Notes:
just support on the U fitting
PLA -
Sparkmaker Replacement Leadscrew nut 3D Print Model
Summary
Due to the slack of the leadscrew nut on the stock sparkmaker unit.. i make a replacement for it.
This nut is around 7mm thick.. if you need a longer type, do pm me.. i will upload.
NOTE.. After print .. DO grease and run Through the Nut with the leadscrew first, it kind of tight.. Once it has go through and re-assemble back to the unit, recommend to run the liner movement print code and let it finish the whole cycle.. 🙂
Print Settings
Printer:
Anycubic kossel min K2
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
0.1
Infill:
100
Notes:
Type of filament reco for this application:
-POM
-PP
-PLA
Do print with 100% infill to ensure the parts are strong. -
replacement moonroof / sunroof switch for lincoln ls 3D Print Model
Summary
mine was missing so I made this.. -
Uno Replacement Box 3D Print Model
Summary
Better Board Game Inserts
Guiding Principles
Board game pieces should stay put no matter the orientation of the box
No Bags!
Use as little filament as possible
Ideally no Supports
The Inserts
This is intended to be a box for storage as well as a convenient way to draw cards. Largely based on the original game design.
Desgin
These were designed using Onshape here.
Print Settings
Printer Brand:
LulzBot Printer:
TAZ 6 Rafts:
No Supports:
No Resolution:
Max layer height ~80% nozzle size Infill:
20% -
Replacement for the closing system of a PVC Window 3D Print Model
Summary
These are plastic replacements for a PVC window I had to repair.
Print Settings
Printer Brand:
Up! Printer:
Up Plus Rafts:
Yes Supports:
Doesn’t Matter Resolution:
0.25 Infill:
Maximum Notes:
Place the pieces carefuly NOT to put the Z axis of the printer along the axis of force, to ensure durability. -
Replacement Battery Cover for PS3 Remote Control 3D Print Model
Summary
A replacement battery cover for the Playstation 3 remote control.
Print Settings
Rafts:
No Supports:
Yes Resolution:
.15mm Layer height Infill:
20%
Post-Printing
Support material can be removed without too much trouble with needle nose pliers. -
Black and Decker Workmate Bench Top replacement Block 3D Print Model
Summary
Lost some of these on my workmate over the years so modeled one up and printed. Works well.
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2S Rafts:
Yes Supports:
Yes Resolution:
.1 Infill:
50% -
Couch Sofa Release Lever Slip-on Replacement Fix 3D Print Model
Summary
The release lever for my couch snapped-off, so I designed this fix for it. Since a “stub” of the original lever still remained, I designed this thing to slip on over the remaining stub. Printed in black PLA to match the couch, though I realize this makes it a bit hard to see in the photos.
The first photo shows the printed part attached to the couch. The second shows the “stub” that the printed part fits over. The third is a reference photo of a still-intact release lever. The fourth is just the part by itself.
Print Settings
Printer Brand:
Prusa Printer:
Prusa Clone Rafts:
Doesn’t Matter Supports:
Yes Resolution:
0.1 Infill:
20
How I Designed This
Fusion360. The .f3d file is included if you wish to tweak it based on the specifics of how your handle broke. -
replacement sterilite container clip 3D Print Model
Summary
I buy lots of these sterilite containers. I imagine a lot of 3D printing hobbyists do. Frequent usage means the clips eventually break. Instead of having to spend another $5 – $12 dollars and throw away a perfectly good container, I drafted a replacement clip.
I know it’s lame, but I use a lot of them and it is wasteful to have to purchase again. The attached image is the container where I keep my coffee. Of course that’s going to break first, using it everyday for over 2 years.
PLA
.3mm Draft
No Support
Hollow / Shell, No Infill
With these basic settings the printed design is stronger than the factory clip. -
30 ml glass ejuice bottle replacement 3D Print Model
Summary
A replacement cap for 30 ml ejuice glass bottle -
Cheap stick enclosure replacement 3D Print Model
Summary
The housing of a cheap USB stick (see photos) was broken easily, so I decided to make a model of the inner part to create a new printable enclosure.
The enclosure models here are very basic on the outside. Feel free to remix or redesign them! -
Replacement Leg Brackets For Futon 3D Print Model
Summary
The plastic legs broke on the center of my futon (which for some reason hinges in the middle?!) and so I sawed off the broken bracket portion of the legs and printed replacement brackets which could be epoxied onto the remaining legs. It works great while in place because the brackets don’t need to be load bearing but I would not be able to move the futon without breaking them. So if you use these be smart about it. This futon was a bad design. -
Replacement Oven Dial Knob 3D Print Model
Summary
I get really attached to my kitchen items. Each one has been carefully chosen at the time of purchase to fulfill a specific purpose and my heart breaks when, after decades of use, a small part either disappears or just craps out, rendering the whole thing unusable.
Well, I’m not gonna let that happen to my beloved Toastmaster toaster oven, doggone it! So, the timer knob popped off and never really fit on again. So, I pulled out the calipers, dusted off the ol’ 3D printer and came up with this thing. Fits perfectly. Lovely, even.
If you found this useful, it would bring me great joy to see your work – so be sure to share. 🙂
Or, better yet, please feel free to dump a bitcoin or two here (you can spare a bitcoin, can’t ya?):
1Py3TUeR8noBN2giHyFV1GfB6x3Kh2WEVv
… include a note to the effect of “Hi 3E8, thanks for the Toastmaster dial thing… my life is infinitely better on account of it and please accept this paltry amount in gratitude”.
You’re welcome! (in advance) 😀
Also, feel free to peruse my other submissions which are almost as varied as they are many:
http://www.thingiverse.com/3E8/designs
Enjoy! -
Magic chef replacement ice bucket 3D Print Model
Summary
Replacement ice “bucket” for my magic chef ice maker. Mine cracked and started leaking rusty water from the motor and the alternative is $20-30 (37 from Amazon/prime)
Not quite at the final design, but will update when I am. Designed it as two parts because it’s just beyond a 200mm bed. The long this party was the easiest to cut off and make assemblable. Just bolt with a 40(?)mm m3 bolt, nut and locking washer.
Print Settings
Printer:
Da Vinci Rafts:
No Supports:
Yes Resolution:
0.2mm Notes:
Supports will probably help. 0.2 or lower, but you will want to acetone/vapor polish to make it (more) food safe. Do all this at your own risk, I take no responsibility, etc. -
Mars Gaming MCP0 mouse replacement scrolling wheel 3D Print Model
Summary
Today the scrolling wheel of my mouse broken. However I tried to glue the two parts together the tiny piece broken broken off every time. So I decided to design and print a replacement part for the mouse and it seems to work very well.
Print Settings
Printer:
Anet A8 Rafts:
No Supports:
Yes Resolution:
0.12 Infill:
50% -
Audi A4 B8 Replacement dash speaker grill for 3 inch mid 3D Print Model
Summary
work in progress
Audi dash speaker grill incorp. 3inch focal flax midrange
best to print on side so support works better
need to watch for delamination
best to print in ABS or petg for heat resistance
reverse/mirror sti for other side
this item will need post prep (sanding, filler and paint)
dash internals may need modifying to fit speaker
Print Settings
Printer Brand:
FlashForge Printer:
Creator Pro Rafts:
Yes Supports:
Yes Resolution:
0.2 Infill:
lots Notes:
heated bed
check for delamination
best printed in ABS or PETG
post cleanup and prep required
Post-Printing
post prep
sanding, putty and paint required
some mods to dash internals to fit speaker basket
needs to be stuck into dash recess – does not use factory clips
when finished suits dash
paint in black plastidip for factory looking results -
Hi-Ho Cherry-O: replacement cherries 3D Print Model
Summary
Replacement cherry for “Hi-Ho! Cherry-O!”
Print the cherry on its side, with supports. The cherry stem may be difficult to remove from supports without breaking the stem off; if needed, use a knife to separate the support material. -
Fiamma aqua 8 pump piston replacement 3D Print Model
Summary
I have a Fiamma Aqua 8 water pump, which lost lots of its pumping capacity.
Turns out the three acryllic(?) “pistons” inside were cracked and broken to pieces.
Replacements are available at Fiamma, but not these pistons as a set, you get almost half a pump when you order the part number. It costs almost 50 euros!
I printed these pistons in ABS with a 0.2mm layer height, 35% infill and 3 outline perimeters as well as 3 top and bottom layers. -
Replacement Sunglass Frames 3D Print Model
Summary
I play volleyball and break a pair of glasses every season (which is why I buy cheap ones…), but this year it happened early in the season, and I decided that I was going to build my own replacement… after all the lenses were perfectly fine.
The frame (green plastic) is modeled after, and uses the the lenses from a pair of inexpensive Foster Grant “Slam Dunk” Polarized sunglasses. (Frame name was imprinted on on temple of the original frames).
I designed these replacement frames from scratch, and tweaked the design a lot to get the lenses to snap in and hold firm just right. I used the original temples (black plastic) and hinge screws.
Print Settings
Printer:
Anet A6 Rafts:
No Supports:
Yes Resolution:
Fine Infill:
60% Notes:
I used supports to the build plane only. -
Lego Battle Droid Leg – Replacement 3D Print Model
Summary
For all those who have lost or broken your battle droid leg(s). I give you a replacement design. This fits a standard Lego Battle Droid torso. You can also use it to start making your own version of Roger Freemaker.
Made on the M3D micro with ABS-R
Print Settings
Printer:
M3D Micro Rafts:
Yes Supports:
No Resolution:
150 Notes:
Works good with ABS-R -
LM27 Enders water tap replacement 3D Print Model
Summary
I created this thing as a replacement for the water tap handle that broke on our LM27 ship.
Print Settings
Printer:
Geeetech i3 Pro C Rafts:
No Supports:
No Resolution:
0,1 Infill:
60 Notes:
I sanded and wiped it with acetone after printing for smooth surface. -
Fidget Spinner Hex Bolt Replacement Piece 3D Print Model
Summary
Don’t want to use a bearing as weight in your fidget spinner? Print this and use a hex bolt in your fidget spinner. This actually works! -
Extended Arms – Spool Holder for Prusa i3 MK2 – Hex Design – Toolless Mounting – Fast spool replacement 3D Print Model
Summary
I Just extended the Arms to fit a 52mm (wooden) Frame. Thanks to Martin Majewski for this fantastic design!
Print Settings
Printer:
Custom Prusa I3 Rafts:
No Supports:
No Resolution:
0,1-0,3mm Infill:
20% Notes:
Grab the other Parts from the original design -
Skimmerflapper 3D Print Model
Simple Skimmerflapper. I needed one because mine broke. Scale to the size you need, print with 10%-15% infill (honeycomb pattern) to make the thicker part float.
-
IKEA GALANT roll-front cabinet (replacement door stop) 3D Print Model
Summary
Love these IKEA GALANT roll-front cabinets. But the plastic stop is too delicate. Make your own replacement part! -
ER250 Front Plate Stock Replacement 3D Print Model
Summary
This is a replacement part for the Eachine 250 Racer front plate.
It has a larger camera port.
I’m waiting on a printed copy .. I like Nylon best so far has a nice finish.
