3DHunt.co

Tag: lack

  • Logitech C270 Lack Enclosure Cam Mount 3D Print Model

    Logitech C270 Lack Enclosure Cam Mount 3D Print Model

    Summary
    This is a quick mount I made for a C270 cam that can screw on to one of the legs of my IKEA Lack enclosure. Screw holes are 6mm
    Print Settings
    Printer:
    Prusa MK3
    Rafts:
    No
    Supports:
    No
    Resolution:
    0.2
    Infill:
    20%

  • Ikea Lack Slot Grommet 3D Print Model

    Ikea Lack Slot Grommet 3D Print Model

    Summary
    I made this slot grommet to go with my Ikea Lack table setup for my Prusa i3 mk2.5
    Two things make this different than other grommets I looked at.

    it is a slot and long enough that when my printer is doing a tall job that my filament isn’t bending at crazy angles.

    The slot is big enough to allow my ptfe tubing to go through it without binding or sticking.

  • Lack Filament Sensor 3D Print Model

    Lack Filament Sensor 3D Print Model

    Summary
    This is a microswitch filament sensor mount I’ve made for the IKEA Lack enclosure.
    It takes 1 KW-12 switch.
    Print Settings
    Printer Brand:
    Prusa
    Printer:
    i3 MK2S
    Resolution:
    0.2
    Infill:
    20
    Notes:
    Support on build plate only.
    The lid snap isn’t perfect at 0.20 layer height. It hasn’t fallen off for me yet but you can try a higher resolution if you like.
    Post-Printing

    Switch preparation
    The switch lever should be slightly bent to an “S” shape as shown above. The first bend is done to insure the filament engages the switch. The bend at the tip is done to prevent the metal lever from snagging on the filament when you pull it back to the spool.
    If you solder the leads you should do it before you insert the switch to the housing. The housing is also designed to allow open barrel terminals but I haven’t tried it yet.
    The switch only goes into the housing with the lever pressed against the switch body. It should spring back into place once the switch is seated all the way in. If the lever stays pressed (meaning the switch is engaged and activated) you’ve probably bent the lever a bit too far up.

  • Prusa Lack Enclosure Door Handles for 20mm x 5mm x 2mm Magnets 3D Print Model

    Prusa Lack Enclosure Door Handles for 20mm x 5mm x 2mm Magnets 3D Print Model

    Summary
    Using the source files from the Prusa Lack enclosure, I resized the magnet inserts for 20mm x 5mm x 2mm magnets, which were easier to find on eBay.
    Print Settings
    Printer Brand:
    Prusa
    Printer:
    i3 MK3
    Rafts:
    No
    Supports:
    Doesn’t Matter
    Resolution:
    0.15 mm
    Infill:
    20%

  • Controlpanel for Ikea Lack Graphic Smart LCD Controllerand W1209 3D Print Model

    Controlpanel for Ikea Lack Graphic Smart LCD Controllerand W1209 3D Print Model

    Summary
    Controlpanel for ikea lack table for Graphic Smart LCD Controller and W1209 Fancontrol
    Its a Extension of thing:87250 and thing:2139389 for Ikea lack

  • LACK Attack #6: Pass the Lack (aka Wire The Lack Stack) 3D Print Model

    LACK Attack #6: Pass the Lack (aka Wire The Lack Stack) 3D Print Model

    Summary
    This is a followup to:
    LACK Attack #5: Inreda the Lack:http://www.thingiverse.com/thing:2673629
    without further adieu….
    Attack 6: Pass the Lack
    Once I lit the Lack, the next step was to get the power cables out of the stack and filament into the stack…
    I looked at some at Home Depot, saw some on Thinkgiverse, decided instead to make my own passthroughs for it as I wanted a single port/type that could be used for multiple things. So far I’ve built a filament filter insert as well as cable inserts, (and a blankoff), I’m sure I’ll come up with a few more as time goes on…
    As always, comments are greatly appreciated, If you’ve made/fixed something to work better please let me know so I can fix it for others.
    Coming Next:
    Attack 7: not sure yet, likely remote mounting the display & Octopi…
    Print Settings
    Printer Brand:
    Prusa Printer:
    i3 MK2S Rafts:
    No Supports:
    No Resolution:
    0.20mm Infill:
    100% Notes:
    Printed in white RepRapper white PLA, 210C nozzle, 60C bed.
    Post-Printing
    Build & Assembly Notes:
    Another simple build:
    Print the parts as needed.
    For each port use 2 1/8″ a hole saw to drill each port.
    Insert the port through the table, tap it down with a rubber mallet flush, snap the lock ring on the bottom to finish off the edge.
    4a. For the filament filter pass-through cut a piece of foam to fit in the filter, snap the bottom on, then use a large needle/stiff wire to push holes through for each of the openings. pulling the filament to the side when you’re done with it will lock it in place.
    4b. for the Wire passthroughs feed your wires through, pop in a cover, and done!
    How I Designed This

    Revisioning:
    v1.0 – Initial upload
    Posted the thing

  • Ikea Lack Table Filament Guide 3D Print Model

    Ikea Lack Table Filament Guide 3D Print Model

    Summary
    Build this as a filament guide through a 1/4″ hole I drilled in my Ikea Lack Table for filament.
    You can view and/or download the source file from here
    The exterior diameter is 4.5mm while the interior is 3mm (good for 1.75mm filament, which is my use case)
    I plan to make a better version of this soon, but this is currently what is fitted in my setup until after the holidays.
    Print Settings
    Printer:
    Anet A8 Rafts:
    No Supports:
    No Resolution:
    0.2 Layer Height Infill:
    100%

  • caisson dagoma de200 3D Print Model

    caisson dagoma de200 3D Print Model

  • Filament Mount for LACK table 3D Print Model

    Filament Mount for LACK table 3D Print Model

    Summary
    Hy there,
    i have mounted my Printers on IKEA Lack tables and now the Filament can easy Mount on the left or right side of the table.
    Print Settings
    Printer Brand:
    Prusa Printer:
    Prusa Clone Rafts:
    No Supports:
    No Resolution:
    .2 Infill:
    10

  • Top-Door-Opener Ikea Lack Enclosure Upgrade

    Top-Door-Opener Ikea Lack Enclosure Upgrade

    Summary
    This will allow you to open and close a door topside for your enclosure.

  • Prusa-I3-MK2 LCD Mount Lack Enclosure

    Prusa-I3-MK2 LCD Mount Lack Enclosure

    Summary
    This is a sample LCD Mount, which is easily removable for the Prusa I3 mk2.