All weapons and attachments from nine to five modeles are actualy .gltf 2.0 bin but cant pick that ;/
Tag: to
-
Call to Arms – Foxholes Pack 3D Model
3 Foxhole vartiants from Call to Arms.The variants are for Crouching, Lying and mixed position.Models are divided into multiple parts and make heavy use of transparent textures.These have been a B*tch to make but here you go.
-
Clever Dripper to Large Tervis adapter 3D Print Model
Summary
Adapter to span needed gap between diameter of 24oz Tervis Tumbler and Clever dripper coffee dripper for those who need a little more coffee in the morning. -
tronxy xy-08n sensor stable mount to Anet A8 3D Print Model
Summary
tronxy xy-08n sensor stable mount
Print Settings
Printer:
Anet A8
Rafts:
No
Supports:
No
Resolution:
0.2
Infill:
100 -
18650 to C-Type Battery Flashlight 3D Print Model
Summary
C_Battery Flashlight change for 18650 Li_battery
C_battery x 5 change for 18650 Libattery x2 。
18650 to C_Battery x1
C Battery-Ext 105mm x1
C Battery-Ext EndCap x2
Print Settings
Printer:
CR-8
Rafts:
No
Supports:
Yes
Infill:
30 -
Uk to USA Plumbing Adaptor 32mm (1-1/4 BSP) to USA 1-1/2 Schedule 40 Fittings 3D Print Model
Summary
I needed a 32mm threaded UK style plumbing adapter to it a USA style schedule 40 P trap.
In true maker fashion i knocked on up on the 3d Printed.
UK Style 32mm / 1-1/4 BSP Female Thread to USA Style 1-1/4 male.
Used a small o ring in the bottom of the threaded section to help seal. -
BBQ 97mm to 40mm Blower Server Fan Duct press fit 1012 KH302 3D Print Model
Summary
this should also fit ANY fan with a output size of ~58mm x ~33mm
i designed this blower duct to attach to a Delta KH302 BFB1012EH blower fan, to use for stoking a fire pit which had a 50mm pipe put through it with air holes. to allow the middle of the fire to suck in air from outside
the outside of the top circle is 40mm and 33mm between the two flat sides.
it is a press fit onto the output of the fan.
thickness of the walls is about 2mm, however it does get quite thin in a couple of spots where the fan presses in.
Haribo Prusa i3 mk2
printed at 60mm/s
0.2mm layers
ABS @ 245C with a 40% fan in a enclosure which reaches about 50C
supports are required for the lip where the fan pushes in until.
this lip is about the same thickness as the fan case, so has a nice smooth airflow.
yet to test this on the fire pit, hoping that a 12v 3amp fan, moving a lot of air through the plastic will keep it cool enough to not melt. (thus why the walls are only 2mm thick)
Print Settings
Printer Brand:
Prusa
Printer:
Prusa Clone
Rafts:
No
Supports:
Yes
Resolution:
0.2
Infill:
20% -
Turbowing Cyclops 3 DVR Camera to Runcam adapter 3D Print Model
Summary
This is a Turbowing Cyclops 3 DVR camera to runcam adapter so it can be mounted in almost all runcam camera mounts. This has not been tested please comment if it don’t work. thank you -
Xiaomi m365 Clamp (scooter Frame Mounting) to add a box or bag – Plateau et Collier de serrage pour rajout de boite ou sac 3D Print Model
Summary
Participant à un groupe Telegram d’entraide/optimisation de la trottinette Xiaomi m365, j’ai modélisé ce plateau équipé de colliers de serrage s’intégrant sur le cadre entre la fourche avant et le deck pour rajouter une boite ou un sac rigide en les pinçant avec les éléments intérieurs,
A assembler avec des vis M5 x 60 à 70 (suivant l’épaisseur de votre boite) à tête cylindrique hexagonale et boulons associés
N’hésitez pas à me faire vos retours pour d’éventuelles améliorations, adaptations nécessaires… -
Micro FPV Camera to HS1177 Size Adapter 3D Print Model
Summary
This is a simple adapter to allow me to fit Micro cameras into models designed for ‘full size’ HS1177 style cameras. I’m sharing this in case others find it useful!
It should make the lens of the Micro Camera present at the front of the model roughly where the camera of a full sized FPV camera would be. There are holes to secure the Micro camera into the housing and two more that replicate the ‘standard’ mounting holes on a full sized camera.
Hope it’s useful to someone! 😀
Print Settings
Printer:
Turnigy Fabrikator II Mini
Rafts:
No
Supports:
No
Resolution:
0.2mm
Infill:
30-50%
Notes:
Flip it 180 degrees for an easy print… -
Knob to Hold a 1/4 inch bolt or nut. 3D Print Model
Summary
You can snap in a 1/4 inch bolt or nut . Use to replace a wing nut. -
new wheels to replace rubber total gym wheels 3D Print Model
Summary
new wheels to replace total gym wheels 4 to a set push bearings into place and install -
35nmm to 9mm film splitter 3D Print Model
Summary
I make this to cut 35mm film into 9mm film for my old spy cameras. -
Nebia Shower Wand Connector to 1/2″ BSP Adapter 3D Print Model
Summary
An adapter that changes Nebia’s proprietary shower wand connector to a standard 1/2″ BSP connector.
Note that the water temperature between the Nebia shower head and the 1/2″ BSP output might be significantly different, and there will be reduced water flow.
Use at your own risk.
Print Settings
Rafts:
No
Supports:
Doesn’t Matter
Infill:
100%
Notes:
Print using PETG for safety and durability. -
Anet A8 simple-fast damper to use with front frame brace 3D Print Model
Summary
I remixed MarcoCammozzo’s Anet A8 simple-fast damper so it can fit it in my front frame brace by Leo_N https://www.thingiverse.com/thing:1857991
Print Settings
Printer:
Anet A8
Rafts:
Doesn’t Matter
Supports:
Doesn’t Matter
Resolution:
0.2
Infill:
30%Overview and Background
-
Adapter for gimbal Tarot T3D III to F450 3D Print Model
Summary
Simple adapter to fix the gimbal Tarot T3D III to the F450 frame.
I used this (https://www.aliexpress.com/item/100pcs-M2-OD-3-2mm-Injection-Molding-Brass-Knurled-Thread-Inserts-Nuts/32815787260.html?spm=a2g0s.9042311.0.0.Z6BrEm) to screw the gimbal to the adapter. -
Swiffer Duster to 3/4″ – 5 TPI ACME Thread Adapter 3D Print Model
Summary
Swiffer Duster handle to 3/4″ ACME thread, which is used on many paint poles. Used to dust the high corners of the house.
Simple remix of two files.
Not printed or tested yet. -
Leader120 to SpiderQuad Mini Split V1.1 3D Print Model
Summary
My new designe SpiderQuad Top for Leader 120 v1.1
This Top for Runcam Mini Split HD -
Tribute to Tiffanys pen holder 3D Print Model
Summary
This was created as a gag gift for some people in the office. It was supposed to resemble the $1000 Tiffany’s sterling silver pen holder.
Best results can be achieved by using primer filler and wet sanding a few times, then painting the model with sterling silver spray paint
The inside of the “can” was painted with Rust-Oleum 284678, Gloss Light Turquoise
Print Settings
Printer:
D-Bot / Anet A8
Rafts:
Doesn’t Matter
Supports:
No
Resolution:
.2mm
Infill:
Doesn’t matter
Notes:
Might want to print the first layer slow to get the best resolution on the text. -
M24 to M22 UK tap adaptor 3D Print Model
Summary
I needed a tap connector for an ebay special tap aerator, unfortunately the tap has a 24mm thread and the aerator a 22mm thread. -
MKS SBASE 1.3 BOX include Dual Mosfet, Four TL-Smoother, and FAN 120mm and Bracket to Alumunium Profile 3D Print Model
Summary
This is MKS Sbase case the dimension is 200x160x63 need a larger printer to do that.
Support for dual mosfet and four TL Smoother
Cooling by 120 mm Fan
add three hole on center to mount to alumunium profile vertically
Print Settings
Printer Brand:
Prusa
Printer:
Prusa Clone
Rafts:
No
Supports:
No
Infill:
20 -
18mm to 16mm screw diameter adapter for 8X zoom lens 3D Print Model
Summary
My friend bought a phone case that lets him screw on an 8x zoom lens. the problem is that the screw was too small. So I made this adapter that allows it to screw right in. I thought this may be useful to a few people so I decided to just upload it. Enjoy.
It’s an 18mm female to 16mm male.
Post-Printing -
Essential GoPro Session to Tripod Adapter 3D Print Model
Summary
An extra simple adapter for GoPro Session that uses the original mounts and adapt it to a standard tripod with the help of an M6 nut (1/4” 20).
The nut fits just right and holds itself in place.
Printed in PLA with 60% infill with a Micromake delta its sturdy enough for the purpose
Enjoy!
Print Settings
Printer:
Micromake Delta D1 Pulley Rafts:
Doesn’t Matter Supports:
Doesn’t Matter Resolution:
0.2 Infill:
60 -
15 mm thru-axle to 9 mm QR front adaptor 3D Print Model
Summary
NOT FOR 3D PRINTING.
Machining is probably best for this.
Measurements taken from the adaptor that comes with Shutter Precision/Exposure QR15 dynamo hubs.
It’s a bit of a loose fit to the nominal 15 mm ID on the hub. You can certainly make it to better tolerances. I just copied what I measured. -
3.5″ hard drive mount to a flat surface 3D Print Model
Summary
These mounts will fasten a 3.5″ hard drive to a flat surface. They are inspired by tkbletsc’s hard drive brackets (https://www.thingiverse.com/thing:2352211), using the heights and sizes in his model, but created from scratch in TinkerCAD. The ledge lifts the HDD appx 6mm from the surface for cooling. The screw holes are 4mm internal diameter, and will fit standard hard drive screws.
This is the first model I have created and uploaded. I needed some hard drive mounts for an arcade machine project. All the other mounts I found where too large and would take too long to print, so I created this. Each mount is only about 2g and prints in around 15 mins (according to Cura 3.1 with a 0.2 layer height and 20% infill). -
Flexible Shaft Coupler 5mm to 8mm 3D Print Model
Summary
Flexible Shaft Coupler – for 5mm Shaft with flat to 8mm Shaft. Print the coupler end pieces from PLA or ABS, the flexible insert with NinjaFlex/TPU, etc. Designed for 4mm screws and nuts to clamp to the shafts.
Print Settings
Rafts:
Doesn’t Matter Supports:
No Resolution:
0.2mm Infill:
40-80% for shaft clamps, 35% for flexible insert -
iPhone 8 Plus Bumb Case with Two Wolves Howling to Apple 3D Print Model
Summary
Case Bumper for an iPhone 8 Plus with the design f two wioves howling.
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2S Rafts:
Yes Supports:
No Resolution:
15 mm Infill:
20 mm -
Anet A8 Laser bracket / Mount (Fits to E3D bracket) IN PROGRESS 3D Print Model
Summary
Anet A8 Laser bracket / Mount (Fits to E3D bracket) IN PROGRESS
I bought an laser to mount on my Anet a8.
But than i would need to take of my hotend, and recalibrate it every time.
Therefor i designed this bracket which i can mount next to my E3D V6.
I made this one for my 2.5W laser. -
HK Diversity Receiver Mount to Ground Station Power Supply 3D Print Model
Summary
Bought Hobby King ground station power supply with HK Diversity Receiver
Power supply comes with two mounting brackets for single receiver and none for diversity one.
So I made one. Will post picture when printed. -
Case for PCB USB to RS485 3D Print Model
Summary
This box to house a small usb to rs485 converter. Box without holes, with side latches.
Print Settings
Printer:
RepRap(Marlin) Rafts:
Doesn’t Matter Supports:
Doesn’t Matter Resolution:
0.2 Infill:
30% + -
FTC 15 Tooth Sprocket 8mm Pitch for Revrobotics Chain fit to Tetrix Hub 3D Print Model
Summary
FTC 15 Tooth Sprocket 8mm Pitch for Revrobotics Chain fit to Tetrix Hub. This part is so that you can use RevRobotics chain with a Tetrix standard kit. -
ShoreTrooper Helmet V2 (SeanKFields) Split to fit 200×200 build plate 3D Print Model
Summary
This is the V2 version of SeanKFields Shore Trooper helmet. All credit for this model goes to him I merely chopped the files to fit my bed. The original files (including the armour) can be downloaded directly from http://shoretrooper.co.uk
I have left the original sized pieces intact and added A and B options which are the bits I needed to split. The face will fit on the bed but I found it easier printing these split up and then gluing back together. I did put a registration tab on the rear rim but after printing a few of my chopped bits it wasn’t necessary so left the rest.
I’ve only managed to get the pieces printed so far and will update the images once I have put it together. I have done some test fits and all pieces line up with no issue.
Legal bit from the included text file (me being SeanKFields):
Usage Rights:
These files are distributed under the Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0) viewable here.https://creativecommons.org/licenses/by-sa/4.0/
Basically, it says that if you intend to redistribute my work in any way, you must credit me as the original creator. This mostly pertains to anyone wanting to use the files commercially. If you’re using the files to print your own helmet, you don’t need to tag me every time you post a picture. You can, but it’s not a part of the agreement.
Speaking of commercial use: Anyone who chooses to do so has my permission to create and sell helmets based on these files. As before, I ask that you not sell the 3D files themselves, but printing and selling a helmet, or selling a helmet cast from a mold made from a printed masters is perfectly acceptable.
As before, there are a few rules. Some of these are new.If you intend to create and sell a product based on these files (printed kit, resin casting, etc.), I ask that you send me a sample of said products. Consider this the licensing fee. I ask this for 2 reasons:
a. It serves as a means for me to identify every vendor using the files.
b. It gives me an opportunity to inspect overall product quality.If you profit from my work, I highly encourage you to take a portion of that profit and do something good in the world with it. Donate to charity. Buy a homeless guy a sandwich. Adopt a shelter dog. It doesn’t matter what it is. Follow your heart.
While I certainly do not require it, I will gladly and graciously accept tips this time. My Paypal address is [email protected]
-
CTC Bizer Makerbot Replicator Dual to Single Titan Aero 3D Print Model
Summary
CTC Bizer Makerbot Replicator Dual to Single Titan Aero
Drop in Dual to Single Extruder Mod with Hotend Cooling duct.
Used original motor and just added E3D Titan with Aero Hotend.
Cooling duct uses M3 Knurl Insert Nut threads from ebay https://www.ebay.com.au/itm/122046120352 I used the M3x4x4 Knurl Insert Nut
You may need to trim one corner of you Aero Cooling Fan as per the images.
The bracket places the hotend nozzle almost exactly over the original Right Hand Nozzle placement to reduce firmware adjustment. Also has striker for the X carriage endstop.
You will need to measure and re drill to move the Z axis endstop up to compensate for the higher nozzle.
Print Settings
Printer:
Lulzbot TAZ6 Custom Rafts:
Doesn’t Matter Supports:
Yes Resolution:
0.3 Infill:
60 – 80% -
Dyson to Progress hoover 3D Print Model
Summary
Waht to do with an dead old handheld Progress hoover.
Convert it to a dyson handheld for stair hoovering. -
fixation to stare a mirror on the wall 3D Print Model
Summary
a fixation to stare a mirror and a plug to hide the screw -
Caliper adapter to measure wider objects 3D Print Model
Summary
To measure a steel wire. Print 2.
Print Settings
Printer:
Tevo tarantula Rafts:
No Supports:
No Resolution:
0.2-0.25 Infill:
20% -
Model 3D Printer to simplify3d. 3D Print Model
Summary
Print Settings
Printer Brand:
Deltaprintr Printer:
Deltaprintr Kit Rafts:
No Supports:
No Notes:
Model 3D Printer to simplify3d. -
V-Slot to Arca swiss tripod mount 3D Print Model
Summary
Ooznest / ustepper time lapse rail tripod mounting plate for home made ooznest time lapse rail.
http://www.instructables.com/id/Ooznest-Ustepper-Motion-Time-Lapse-Video-Rail/
Print Settings
Printer Brand:
Prusa Printer:
Prusa Clone Rafts:
No Supports:
No Infill:
50% -
Cocktail pot 3D Print Model
As I realized a few touilletes and I printed it I needed a utensil to be able to store them.
-
Colgate “Snap on tub to screw on travel” toothpaste transfer connector 3D Print Model
Summary
Inspired byhttps://www.thingiverse.com/thing:158910
andhttps://www.thingiverse.com/thing:800679
and especially this customizable one:https://www.thingiverse.com/thing:1972293
where I used it to create the bottom (screw to the small Colgate tube) and then added a snap on connection in tinkercad.
So this “thing” connects snap on Colgate big tubes to screw on Colgate little travel tubes.
It did not need supports. -
PS Vita Gamecard to SD case 3D Print Model
Summary
PS Vita Gamecard to SD card adapter case.
This finishes off your game card adapter so that it locks in and ejects like a real gamecard.
This is really thin, and requires all layers to be printed at 0.1mm to function correctly.
Print Settings
Rafts:
Yes Resolution:
0.1 -
Animalarm – a sensor to control pet movements 3D Print Model
Summary
A simple but elegant project to create a “pet zone alarm” in your house. It uses infrared motion detectors to sense when a pet (or small child) is moving through a doorway or hall and sends out a loud tone. It does not beep when a (tall) person moves through the same area. With a bit of training animals recognise where they are welcome – without having to use physical gates.
NOTE: WIP – Some electronic component values are subject to change
Post-Printing
Caveats
Obviously, you will need to be able to get the PCB manufactured. The files are all there to do so and it is very cheap. And of course you need the skills and equipment to source and assemble the electronics!
If you want to use a different buzzer, you will need to make your own shell – but the electronics at least will work for you… Application
There is a single trimpot to set the length of the beep, once the alarm is triggered. You can also change component values (C1 in particular) to alter the delay before the alarm goes of before triggering the alarm. Set it longer if the system is triggering falsely.
There are pads in the 3D print design at the top and bottom of the Animalarm. Use double sided tape or bluetack at those locations to mount the alarm on the wall / doorway.
How I Designed This
How this works
The Animalarm uses two PIR (passive infrared) detectors to detect and discriminate between pets and people. The detector needs to be mounted on a door / wall about a meter above the ground. One PIR “looks down”, the other “looks up” to detect motion. A pet only triggers the lower detector and sets of the alarm. If a person is detected, the alarm either never triggers or is shut off.
The circuitry is built around a single CMOS chip and a few transistors – and of course battery, buzzer and PIR detectors. The circuitry is incredibly power efficient, drawing less than 30µW normally and only 10mA when triggered. This means the batteries will probably last a year in normal use… Electronics
The attached files include:
the Eagle design files (schematic and PCB)
Circuit schematic
PCB layers images
Gerber files for the PCB to be produced by seedstudio.com
List of special components and their sources
All the components are incredibly cheap; the PIR detectors are less than $2, the circuit board less than $1; indeed the most expensive component is the buzzer. The total component cost is about $15 (printed shell aside) -
Antech Light to GoPro Bracket 3D Print Model
Summary
This is a bracket to adapt an Antech light (http://a.co/jfEcPOR) to a standard GoPro mount.
Print Settings
Printer Brand:
Tinkerine Printer:
Ditto Pro Rafts:
Yes Supports:
Yes Resolution:
0.2mm Infill:
80% Notes:
The default mount that came with the light did not seem strong enough to resist a mountain bike ride, which is what I need it for.
I included a cutout for the cable to exit towards the front, but there is actually enough space for it to go directly to the back between the “legs”, as shown on the pictures.
Post-Printing
After printing, I had to trim a bit the bottom face for the stop to fit in the grove between the cooling fins. Also, the fit was extremely tight; the GoPro mount was really bent at first. After a few days under stress, it looks like the bracket extended a bit and now the fit is perfect.
The model I uploaded has a slightly larger inner diameter and slightly thinner stop, so that should provide an easier fit (although not tested). -
Bed and bebside table 3D Model
High level of detail 3d models, 14 assemblies 60 parts, I include fasteners.All the details in 3D CAD models are connected by equations, therefore I recommend to change the sizes, colors, textures in the program SolidWorks.Advantages of 3D CAD models for Manufacturers and Designers.For Manufacturers In one click we change the size of the bed at the request of the customer (with preservation of design) When changing the size of the bed, the parts drawings, control programs for the CNC machine (integrated SolidCAM CAD program in SolidWorks) are automatically changed, resulting in the rapid production of a customized bed in production The bed model is designed for manufacturing from solid wood with the necessary fastening of partsFor Interior Designers In one click, we change the color and texture of the bed for a quick display to the customer If necessary, the model is easily imported by the SolidWorks program in 3ds Max and other formatsMore on this 1. Resize the 3D model in one click1.1 The size of the bed varies on the mattress width 30 – 80 in (76 – 203 cm), length 75 – 98 in (191 – 249 cm) with preservation of design1.2 It is also possible to customize the dimensions of the bed1.3 The details of the 3D bed model are related by equations. With the change in the size of the bed, all the details change at the same time, changing to the desired size1.4 All this is shown in the attached video2. All bed parts are designed for manufacturing in solid wood2.1 All parts in the 3D model are connected by means of joinery of parts2.2 If necessary, you can easily change joinery connections in the model by adjusting them to the existing equipment in the production3. In one click, we change the color and texture of the bed (by changing the configuration of the model), while the model with the new color and texture can be dynamically rotated and moved to show the customer, all this is shown in the attached video4. The bed is part of the bedroom, which includes (chest of drawers, dressing table, closet)Rendering with Solidworks Photoview 360.
-
Free Standing Boxing Punch Bag Bob Dummy 3D Model
High quality 3d of Free Standing Boxing Punch Bag Bob Dummy.-Model is really there, done carefully, according to the real dimensions.-scene for 3ds Max 2012 and V-Ray 2.0!!!In file only 3d model without interior!!!
-
MPCNC spacer for 608zz to remove any play in rails 3D Print Model
Summary
This is a simple spacer you can put on your 608zz bearings to make the ride more smooth without any play. PLA worked great for me and make sure your increase or lower your layer width so you have a good bond. .44 worked for me on a .4 nozzle -
16x16mm to 20x20mm ESC/Flight Controller Adapter 3D Print Model
Summary
Used to mount a 16x16mm nano ESC or Flight controller on a frame that supports 20x20mm boards.
Best printed on ABS wtih 100% infill
For the 20x20mm holes, you will need to use thread using a M3x0.5 tap. For the 16×16, you can either thread using a M2x.04 tap or enlarge to use a M2 screw.
Print Settings
Printer Brand:
FlashForge Printer:
Creator Pro Rafts:
No Supports:
No Resolution:
.2mm Infill:
100 -
Micro SD to SD extension adapter for 2020 extrusion 3D Print Model
Summary
This is a redesign of https://www.thingiverse.com/thing:1802502 adapted for 2020 extrusions.
Needs 1 M5 x 10 button head socket head cap screw and a hammer nut or a Square if you are assembling your AM8 (Anet Metal A8) -
compartment box to CD Jewel case 3D Print Model
Summary
Compartment box designed into CD Jewel case. STL files are ready for case with 4 booklet holders with 9 compartment cobinations.
I made additional 5&6th (booklet) holes and vertical / horizontal boxes in source FreeCAD file. You can combine it freely. -
Artistique bed 3D Model
Artistique_bed.W 2252,86mm,D 2445,27mm,H 1255,99mm.Editable Mesh + Editable Poly in Group.1Multi/sub material.Materials are named on sense of their purpose.The objects are named by their own specific names.Groups are named by respective to name objects in Catalogue.Fabric color made using procedural map.Default Scanline Renderer.————————————TotalPolys: 38036Verts: 25155MAX file Size:2,69MB3DS_file Size:1,06MB
-
Brackets to join 25×25 mm wooden stakes to create a garden frame 3D Print Model
Summary
I made these brackets to build a framework from 25 x 25 mm wooden stakes for bird netting to protect my raised strawberry garden. It has proven to be very robust (over engineered one might say!) and the bird netting simply drapes over the frame from being attached to an adjacent fence. Because my stakes were a little under size I have drilled each bracket and screwed through the bracket into the stake to give it rigidity.
I enabled supports for the several parts that required bridging of significant area but my printer overrode that and printed quite satisfactorily just as if supports had not been enabled.
Sliced with Slic3r and printed at .3mm layers since surface finish was not a priority.
Print Settings
Printer:
FLSUN i3 clone Rafts:
No Supports:
Doesn’t Matter Resolution:
.3 mm Infill:
25% -
hermit crab shell 3D Model
with your creativity, you can add more details in the shell to give a hermit crab a better home
-
3D Cup
Cup a high quality model to add more details and realism to your rendering projects. This model is suitable for use in broadcast, high-res film closeups, advertising, design, visualization, presentation etc.The model is accurate is built to real-world scale.Units used: centimeterModels resolutions are optimized for polygon efficiency. (In 3ds Max, the function ‘Meshsmooth’, ‘TurboSmooth’ can be used to increase mesh resolution if necessary.)High resolution texture ensures good display quality at extreme closeups.High quality polygonal model, correctly scaled for an accurate representation of the original object.Model is fully textured with all materials applied.All colors can be easily modified.All textures and materials are included.3ds Max models are grouped for easy selection.Model does not include any backgrounds or scenes used in preview images.Lighting absent.The model was made in 3Ds Max 2011. Visualization does require installation of additional software V-Ray._________________________________________________This model contains 2 separate object. Objects have intelligent names.In scene there are 3 textures:Coffee – resolution 2000 x 2000, format (JPG).Cafe-displace – resolution 2000 x 2000, format (JPG).Life-Begins – resolution 2000 x 2000, format (JPG).The following textures are additionally included in the set to change the appearance of the cup:Coffee-shop – resolution 2000 x 2000, format (JPG).Exo-Cup – resolution 2000 x 2000, format (JPG).Football – resolution 2000 x 2000, format (JPG).Nescafe – resolution 2000 x 2000, format (JPG).Take-Wake – resolution 2000 x 2000, format (JPG).Archive in format rar._________________________________________________All preview images are rendered with V-Ray 2.0 as Renderer. (subdivision level 1)If you press the on my nickname in the right edge of the page, you will see my gallery where you can download a few free samples. Do not forget to comment on my work.
