Nave from the television series V the final battle (the vositors) broadcast between 1983 and 1985 in the United States.The ship has a total size of 13.3 cm long, 5.1 cm high and 10 cm wide. Can be scaled to the desired size.You can print the landing gear if you wish, the windows can be printed separately, recommended in black.3D printing settingsNAVERequires supportLayer height: 1.5 mmFilling: 20%.Printing speed: 60 – 70 mm/sPlate adhesion: edgeWall thickness: 1.2 mm or moreUNDERCARRIAGESupport: noLayer height: 1.5 mmFilling: 20%.Printing speed: 60 mm/secPlate adhesion: edgeWall thickness: 1.2 mm or moreGLASSESSupport: noLayer height: 1 mmFilling: 100 %.Printing speed: 60 mm/secPlate adhesion: edgeWall Thickness: 0.8 mm or greater
Tag: Slider
-
SHIP T-47 STAR WARS 3D Model
The T-47 hovercraft, also known as the Snowspeeder, is a small ship, developed by Incom’s shipyard, originally as a cargo ship but modified by the engineers of the rebel alliance to fight under the hostility of the icy planet of Hoth.The design is very easy to print, you can print in two parts or complete either of the two options have separate windows (attached are the necessary files).It is 16 cm long, 12 cm wide and 4.5 cm high. In the photographic record you will find the way of assembly.3D printing settingsLayer height: 0.15 mmFilling: 20%.Plate adhesion: edge 0.8 mmSupport: yesTemperature: depending on materialPrinting speed: 60mm/secWall thickness: 1.2 mm or more
-
Spider-man Homecoming 3D Model
3D model of MCU Spider-man as seen in Captain America 3 (civil war) and Spider-man Homecoming.Model made with Cinema4D.Model rigged, textured, animated eyes, webwings ON/OFF.available in native .C4D, Arnold renderer .C4D version, FBX & DAE.animated eyes for .C4D files only.
-
2 Mode Slider 3D Print Model
Summary
Just a simple slider with a small cutout to make room for a label on each side. Good for use on things like dishwashers to mark as clean or dirty etc. You just need to make a label for each side and stick them onto the indented portion. I have included the solidworks parts so that you can add raised text or art etc to the base if so desired!
Print Settings
Printer Brand:
Prusa
Printer:
Prusa Clone
Rafts:
Doesn’t Matter
Supports:
Doesn’t Matter
Resolution:
Medium
Infill:
50%+
Notes:
Some printers have issues printing the little notches on the base and face-plate. If you have these issues, use supports.
Post-Printing
the face-plate will be a tight fit into the base, but align all four corners with the slider under the face-plate and squeeze the midpoints of the face-plate. Push, and it should click in.
NOTE: It is VERY hard to remove the face-plate after install. MAKE SURE YOU HAVE EVERYTHING THE WAY YOU WANT IT FIRST! -
Fidget Slider 3D Print Model
Summary
Small fidgeting toy.
Inspired by Make Anything’s twisted toy design.
Print Settings
Printer Brand:
Creality
Printer:
CR-10 Mini
Rafts:
No
Supports:
No
Resolution:
0.1 mm
Infill:
100%
Notes:
Use 100% infill to gain some weight or fill the twisted tube with some material (could use a glue gun). Don’t forget to print 2 End_caps.
Post-Printing
Get better results by sanding the model. I use 400 grit sandpaper first and then 1000 grit. -
Pixel 2 XL Slider Case 3D Print Model
Summary
Basic Slider case for Pixel 2 XL. Test printing shortly. -
Modern architectural window horizontal slider 3D Model
Modern architectural window horizontal slider
-
Table slider Ultrasport F-Bike 150 and F-Bike 200 3D Print Model
Summary
This is a slider for a “Ultrasport F-Bike 150 and F-Bike 200 table” which I designed because the table was too far away for me. With this pieces the table is ~20cm closer and in addition you can remove the table easily and reduce the width when the bycicle is closed.
You must print “top.stl” 2 two times.
Extra staff you need:
4x screws
4x nuts -
Camera mic holder 3D Print Model
It’s a microphone holder for DSLRs and other cameras. The microphone holder is attached via the HOT SHOE connector, which is usually located on the top.
-
Camera mic holder 3D Print Model
It’s a microphone holder for DSLRs and other cameras. The microphone holder is attached via the HOT SHOE connector, which is usually located on the top.
-
Lee Pro 1000 Reloading Press Case Slider 3D Print Model
Summary
This is a case slider for a Lee Pro 1000 reloading press. I designed this to replace the one on my press that got damaged. The gap for the shell has been sized to match a 9 X 19 shell, but may need some adjustment. The hole where the guide rod fits still needs to be drilled out. I have included the123 D Design file to allow for tweeking -
Dolly Camera on Dual Rail Slider 3D Model
This is a representation of my DIY ‘Dolly Track Manual Slider’ .3D model to add more details and realism to your projects.for this render, i used hdri (not included)according to your HDRI, some adjustments on materials must be done*********************************Features: – Model resolutions are optimized for polygon efficiency(in 3ds Max the meshsmooth function can be used to increase mesh resolution if necessary).- All colors can be easily modified. – No part-name confusion when importing several models into a scene. – No cleaning up necessary, just drop model into your scene and start rendering.- No special plugin needed to open scene.- HDRI & scene not included*********************************File Formats:- Max 2013 – OBJ (Multi Format) – FBX (Multi Format) – Cinema 4D R15 Every model has been checked with the appropriate software.*********************************Hope you like it! Also check out my other models, just click on my user name to see complete gallery.Infos about my work:I work always my files with a lot of attention to details, good topology and optimizes polygons, I also bring a serious touch in the provided textures.I would like to thank every guys who bought my files, you motivate me to produce some more very nice 3D models.Newlc – 2017
