Summary
25° Session Mount. I haven’t tested it yet it but it should work
Tag: session
-
Armattan Rooster/Chameleon Ti GoPro Session Mount 25° 3D Print Model
-
GoPro Session 5 protector cap 3D Print Model
Summary
Gopro Session Cap to hold your camera in place. Print in TPU. This was designed for the seesion and has a front and back lip that locks the camera in place. Does not show in superview. I have never had an eject with this cap. -
Essential GoPro Session to Tripod Adapter 3D Print Model
Summary
An extra simple adapter for GoPro Session that uses the original mounts and adapt it to a standard tripod with the help of an M6 nut (1/4” 20).
The nut fits just right and holds itself in place.
Printed in PLA with 60% infill with a Micromake delta its sturdy enough for the purpose
Enjoy!
Print Settings
Printer:
Micromake Delta D1 Pulley Rafts:
Doesn’t Matter Supports:
Doesn’t Matter Resolution:
0.2 Infill:
60 -
BOLT Blackops V2 Go Pro Session Mount 3D Print Model
Summary
GP Mount for the Bolt Blackops V2.
We suggest using (countersunk) washers on all four mounts.
Please change the front screws to something longer, circa 14-16mm.
The rear screws, use nylon nuts or drill the holes out to M4.5 and use inset nuts.
Thanks -
Swissknife : GoPro session mount 35degrees 3D Print Model
Summary
Gopro Mount for swissknife frame.
The bottom part can be attached with 2 zip ties to the top plate. -
GoPro Session mount for Martian 2 frame 3D Print Model
Summary
30 degree GoPro Mount for martian 2
Martian 2 frames aren’t consistent, this is for the following mounting dimensions
Mounting points are ~45mm x ~32mm
more angles incoming
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 V2 Rafts:
Doesn’t Matter Supports:
No Resolution:
.02 Infill:
20% Notes:
Print flat on screw mounts -
Plate Adapter for Gopro Session for Zhiyun Gimbal 3D Print Model
Summary
Center Mount Plate Adapter for Gopro Session for Zhiyun Gimbal
Print Settings
Printer:
CR10 Rafts:
No Supports:
No Resolution:
.2 Infill:
20 Notes:
you have to have a 12mm steel dowel mounted with a 6mm screw to make this balance -
gopro session strong protective case + glass 3D Print Model
Summary
strong full-body go pro session case, one is open on the back, the other can fit a plastic cap
i attached a dxf with the path for cutting the protective “lens” in 2-3mm of PMMA or PC
also i’ve uploaded a clip to hold the protective lens on standard hollow gopro frames
other photo soon, work in progress -
GoPro Session Strap Plate 3D Print Model
Summary
This is a little GoPro Session mounting plate I threw together for a friend.
He has the Session 5 but it might work for other Sessions.
It is designed to have a battery strap pass through the slots and secure it to the frame of a quadcopter (drone). -
MQC-ONE or 40Width x50Length bolt, session mount 3D Print Model
Summary
40width by 50 length gopro session mount or runcam cube. -
GoPro HERO4 Session 3D Model
The 3D model was created on real base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.Model formats:- *.max (3ds Max 2008 scanline)- *.max (3ds Max 2008 vray)- *.fbx (Multi Format)- *.obj (Multi Format)- *.3ds (Multi Format)- *.mb (Maya 8.5)- *.lwo (Lightwave 6)- *.c4d (Cinema 4D 11)* renders Are made in 3ds Max 2008 using vray 1.5 (studio environment is not included in the set)If you need any other formats we are more than happy to make them for you.The model is provided combined, all main parts are presented as separate parts therefore materials of objects are easy to be modified or removed and standard parts are easy to be replaced. If you experience difficulties with separating standard parts we are more than happy to give you qualified assistance.We greatly appreciate you choosing our 3D models and hope they will be of use.We look forward to continuously dealing with you.Sincerely Yours,Hum3D Team
-
E3D – GoPro Hero 5 Black 3D Model
This pack:Element 3D V2.2 ( All colors )models preset easy to use- 1 file OBJ High poly- 1 file OBJ standard- 1 file C4D R12 standard render- 1 file 3ds max 2012 standard material- E3D file full materials set up like previewsHow to use it?1. Open After Effects CC 2014 ( or higher) and create new composition ( You need Element3D V2.2 to use )2. Create new Solid layer and add Element effect. ( Effect/Video Copilot/ Element )3. Click Scene Setup4. Click on IMPORT inside Element3D scene setup5. Choose my .e3d preset for the model and press Open.If you dont see the model do not forget to right click on the model name and press Replace model then select the .obj model file in the respective models folder.
-
GoPro foldable tripod
I was looking for a simple lightweight GoPro tripod – so I came up with universal head that can use legs with different angles.
For now, there is 40 deg. version perfect for Session, and 60 deg. for classic GoPro to ensure better stability.
