3DHunt.co

Tag: printers

  • AM8 Duel Mosfets Mount (Or other 2040 Extrusion Frame 3D printers) 3D Print Model

    AM8 Duel Mosfets Mount (Or other 2040 Extrusion Frame 3D printers) 3D Print Model

    Summary
    This is a duel mosfet mount for a am8 frame. Do to the the size of cheap eBay mosfet you might have to drill the holes out very little. This will work with any 2040 Frame printer.

  • Removable Bed Levelling Probes for Delta Printers 9.5mm effector 3D Print Model

    Removable Bed Levelling Probes for Delta Printers 9.5mm effector 3D Print Model

    Summary
    This is a remix/remake of Removable Bed Levelling Probes for Anycubic Kossel Linear designed by peaberry for 9.5mm effectors.
    Attached FreeCAD files.
    Print Settings
    Printer:
    prusa i3
    Rafts:
    No
    Supports:
    No
    Resolution:
    0.2
    Infill:
    30%

  • 30mm Calibration cube for SLA printers – Hollow 3D Print Model

    30mm Calibration cube for SLA printers – Hollow 3D Print Model

    Summary
    This is a hollow cube with drain holes to minimise suction. Stick it on some supports, print it and measure
    When I used this on my Moai with v1.15 firmware, using “m” as the relevant cube measurement, the formula to calculate what put in the relevant X or Y entry is:
    900*(30/m)
    I haven’t used it on my D7 yest, but I’m sure you can work out what formula you would need to use.

  • Autolevel mount for V6 delta printers 3D Print Model

    Autolevel mount for V6 delta printers 3D Print Model

    Summary
    Why
    This is a quick design for an autolevel probe that should fit most Delta effectors like the Anycubic Kossel, FLsun etc. etc.
    The probe is specifically made to support Delta printers with effectors that clamp the top end of a bowden V6 extruder. It’s probably too short for a V5 hotend.
    Features
    Fits most Delta effectors
    Designed to match the e3d v6 hotend in length
    Uses standard M3 mounting hardware (nut and bolts)
    Uses standard endstop switch
    Instructions
    Print it in PETG with multiple walls and slow speed to get the strongest part.
    Print without a fan to get the strongest part.
    No supports required
    If you encounter inconsistent bed leveling, your effector may not be entirely level. Mount the probe closer to the center, or upgrade to a hotend-mounted autolevel probe.
    Open Source
    As always the original design file (fusion360) is included, so feel free to improve it (or learn from it)!

  • Filament guide for Prusa Anet Geetech CTC printers 3D Print Model

    Filament guide for Prusa Anet Geetech CTC printers 3D Print Model

    Summary
    This is my version of filament guide based on this one:https://www.thingiverse.com/thing:1240326
    A larger pipe will keep more straight the filament at the end of the reel, when the loops are smaller.
    Suitable for printers:
    Prusa
    Anet
    Geetech
    CTC printers
    …and many models with a frame 5mm width.
    Feel free to adapt the files to your needs.
    Thank you so much for you comments, like, download and collecting!
    Print Settings
    Printer Brand:
    Prusa Printer:
    Prusa Clone Rafts:
    No Supports:
    No Resolution:
    0,2 Infill:
    100% Notes:
    For better results, use cooling fan.

  • Corner stand for printers 3D Model

    Corner stand for printers 3D Model

    Corner stand with two pluteus for printers or another electrical Technics

  • Interlocking MacBook Pro Retina Stand for Smaller Printers 3D Print Model

    Interlocking MacBook Pro Retina Stand for Smaller Printers 3D Print Model

    Summary
    For those of you with a smaller printer like me, this interlocking remix of Thomasdc_’s geometric MacBook Pro Retina Stand (https://www.thingiverse.com/thing:1330829) will allow you to print this great stand in multiple parts without having to glue or fasten anything together.
    The parts are an interlocking slide fit that’s very secure, and is best assembled via tapping them together with a weighted object (i.e. small hammer or large wrench)
    The gap in the interlocking pieces is 0.15mm so layer heights above this will be tight. I have printed at 0.175 and it’s a nice tight fit.
    Print Settings
    Printer:
    Monoprice Select Mini Rafts:
    No Supports:
    No Resolution:
    0.175mm Infill:
    20% Notes:
    Note that gap between interlocking parts is 0.15mm. Layer heights will affect the fit of these parts because of orientation of the locking features. They are oriented this way because the stand is very sturdy as a result and doesn’t require glue.
    Post-Printing
    Inspect the interlocking channels for zits and other inconsistencies clean the up as required. Mine came out nice and didn’t require any clean up.
    How I Designed This
    I traced the .STL file in Fusion 360 and created my own part splits and locking features once I had the outline traced. I changed the bracing just because I like the look of triangles.

  • Warhammer 40k Modular Building Split for Small Printers 3D Print Model

    Warhammer 40k Modular Building Split for Small Printers 3D Print Model

    Summary
    I cut this up into chunks small enough for small build areas.

  • Paint filter support for SLA printers 3D Print Model

    Paint filter support for SLA printers 3D Print Model

    Summary
    Paint filter support for SLA printers (Formlabs Form 2, …)
    Print Settings
    Rafts:
    Doesn’t Matter Supports:
    No Resolution:
    200 microns