3DHunt.co

Tag: Flsun

  • Stepper motor mount for FLSun QQ 3D Print Model

    Stepper motor mount for FLSun QQ 3D Print Model

    Summary
    This is for folks who prefer shorter bowden tube & easier to load filament when the printer is position in a confined area. I use a little “bluetak” to make it less likely to slide along the side rail.

  • Carriage Module for FLSUN Cube 3D Print Model

    Carriage Module for FLSUN Cube 3D Print Model

    Summary
    This is to be a set of carriages for the FLSUN Cube, suitable for the three different extruders supplied in the kit. Each carriage can be swapped in and out with minimal effort by clipping Iand optional bolt) on to the universal belt bracket.
    Very much a work in progress.
    First stage are the STL’s for the Acrylic carriages (Single and Dual) supplied with the kit.
    All work done in SCAD – file attached

  • flsun cube rod end stop 3D Print Model

    flsun cube rod end stop 3D Print Model

    Summary
    this was made to replace the end stops on my flsun cube as the perspex ones break easily.
    Print Settings
    Printer:
    flsun cube
    How I Designed This
    this was designed in microsoft builder.

  • FLSUN Prusa i3 RAMPS Container 3D Print Model

    FLSUN Prusa i3 RAMPS Container 3D Print Model

    Summary
    I’m working on cleaning up my printer station and couldn’t find a container for my RAMPS board that I liked, so I’ve designed this one. I haven’t printed it yet so it most likely still needs tweaks. As soon as I finish printing my enclosure brackets I will be making this next.
    I’m using an 80mm wide and 30mm deep fan for cooling the board.
    The idea of the design is that the cables will come in through the large circle opening, can be wrapped around the pegs to shorten them, then run them through the gaps to the board itself. The fan cable is fed through the small hole in the corner of the fan guard, then through the hole in the lid. The latch on the right hand side is meant to go on first, then the one on the left (really not sure if that’s going to work or not).
    Because I’m building an enclosure I didn’t design the mounts to attach to the frame of the printer but to the outside wall.
    The only sections that should need support is on the fan guard depending on which side you print up, and possibly the latches on the container itself.
    If anyone notices anything I got wrong, suggestions for changes, etc, please let me know! If you print one, let me know how it went!

  • FLSUN Cube X carriage restyling 3D Print Model

    FLSUN Cube X carriage restyling 3D Print Model

    Summary
    My X carriage broken and i created restyled one. Some things bit simplified, i tried to make it more reliable, belt mount included. If hotend radiator doesn’t fit to it’s mount, just hot up radiator with boiling water and put to mount – mount will take your radiator shape.
    FreeCAD source file included as usual 🙂

  • Fan ducts remix – Flsun cube printer 3D Print Model

    Fan ducts remix – Flsun cube printer 3D Print Model

    Summary
    Another crudely remixed file.These are the fan ducts I’m using for the Flsun Cube printer. Hopefully this helps someone else out.
    The ducts work with this fan mount https://www.thingiverse.com/thing:2358917

  • Flsun i3 x/z axis 45 mm redesign

    Flsun i3 x/z axis 45 mm redesign

    Summary
    I’ve decided to make a version of my x/z-axis redesign with a center to center distance for the x-axis rods of 45 mm, with the belt centered. There have been many requests from certain people who want to use a prusa carriage with their flsun printer, so if you’d like to print an original prusa carriage with 45mm rod spacing and the belt centered, these are the brackets for your flsun i3!
    For reference, this is the complete redesign with the original 70 mm spacing. Many people have reported success with this design alternative also.http://www.thingiverse.com/thing:2116748