Sandvik jaw crusher 1107RJ complete drawing
Tag: crusher
-
Skullcandy Crusher Wireless Headphone 3D Model
This file contains a 3D model of the Skullcandy Crusher Wireless Headphone.The model is made with Cinema4d and exported to the following filetypes:.C4D.C4D Octane Render.3DS.FBX.DXF.STL.OBJMaterials and baked Textures are included.Polygons: 3482Note: The lighting and studio setup is not included.
-
1954 Ford Mainline (Crusher) 3D Model
3D модель постапокалиптического автомобиля из игры “Mad Max”Карты спекуляра, эмбиент оклюжн и т.д. в каналах текстуры “Tex_XXXX_2.dds”Возможные багипроблемы в автомобиле:Рессоры и амортизаторы в “прижатом” состоянииРазмер колес не соответствуют оригиналу(масштабировал на глаз)Возможно потребуется поправить uv координаты некоторых деталей
-
1954 Ford Mainline (Heavy Armored Crusher) 3D Model
3D модель постапокалиптического автомобиля из игры “Mad Max”Карты спекуляра, эмбиент оклюжн и т.д. в каналах текстуры “Tex_XXXX_2.dds”Возможные багипроблемы в автомобиле:Рессоры и амортизаторы в “прижатом” состоянииРазмер колес не соответствуют оригиналу(масштабировал на глаз)Возможно потребуется поправить uv координаты некоторых деталей
-
1954 Ford Mainline (Armored Crusher) 3D Model
3D модель постапокалиптического автомобиля из игры “Mad Max”Карты спекуляра, эмбиент оклюжн и т.д. в каналах текстуры “Tex_XXXX_2.dds”Возможные багипроблемы в автомобиле:Рессоры и амортизаторы в “прижатом” состоянииРазмер колес не соответствуют оригиналу(масштабировал на глаз)Возможно потребуется поправить uv координаты некоторых деталей
-
1300 x 1350 Impact Crusher Engineering Drawings 3D Model
1300 x 1350 Impact Crusher Engineering Drawings
-
HIDROCONE CRUSHERS H4800 Cone Crusher Sandvik 3D Model
HIDROCONE CRUSHERS H4800 Cone Crusher (Sandvik)
-
Barmac-vsi Vertical Impact Crusher 3D Model
Barmac-vsi Round crusher 3D model 3D model Vertical Impact Crusher
-
Cone crusher OC1000 3D Model
Cone crusher OC1000，This project has 2D drawings, 3D models and detailed instructions
-
HIDROCONE CRUSHERS 2000 Cone Crusher Sandvik 3D Model
HIDROCONE CRUSHERS 2000 Cone Crusher (Sandvik)
-
Crusher 3D Model
Crusher is autonomous off-road Unmanned Ground Combat Vehicle developed by researchers at the Carnegie Mellon University’s National Robotics Engineering Center for DARPA.It is a follow up on the previous Spinner vehicle. DARPA’s technical name for the Crusher is Unmanned Ground Combat Vehicle and Perceptor Integration System, and the whole project is known by the acronym UPI, which stands for Unmanned Ground Combat Vehicle PerceptOR Integration.Robot have space frame and skid plates to protect the robot from heavy blows from objects like boulders. The Crusher also has a hybrid engine capable of travelling several miles on one battery charge. The diesel engine then turns on to continue powering the Crusher and to recharge the battery module.Model dimensions:- length – 4940 mm- width – 2460 mm- height – 2078,9 mmDesigned in Solid Works 2012, rendered in Keyshot 5.0.99.Useful links:http://www.nrec.ri.cmu.edu/projects/crusher/https://en.wikipedia.org/wiki/Crusher_(robot)https://www.youtube.com/watch?v=dluiPYDDbtwhttps://www.youtube.com/watch?v=WOD5NF48byohttps://www.youtube.com/watch?v=EZtlTHEHj4Mhttps://www.youtube.com/watch?v=46rkQiXs6Eg
-
Soda Can Crusher 3D Print Model
Summary
This actually works. I usually just slightly dent the side of the can before crushing, because it makes it a LOT easier to crush. There is no reason to print the Can, it is just included to help visualize where it goes.
This was sized to almost exactly fit the size of my print bed. I had to print the handle with the gears vertical, and the handle laying down (at an angle) in order to fit it. Some of the teeth didn’t print properly, but those teeth were not actually used.
I didn’t mark this as configurable yet, as I have only ever tried the one set of settings.
This requires two ball bearings where the handle/gear meets the top piece that slides up and down. You will have to measure the bearings that you are using to make them fit, the dimensions are in the .scad file.
When assembling the unit, insert the handle such that the handle is almost horizontal when on an uncrushed can, you need the leverage. (not the way it shows in the file).
Also make sure to lubricate the top slider using vaseline or grease.
It does not crush the can as flat as some can crushers, it basically gets it down to about 20-25% of the full size.
Each part was taking 15 hours to print, and I got bored with waiting so did not do a lot of experimenting with slightly better designs. Please give it a try, make some modifications/derivatives and insert comments.
I had fun making it, I hope you enjoy it.
Print Settings
Printer Brand:
FlashForge Printer:
Creator Pro Rafts:
No Supports:
Yes Resolution:
0.2 Infill:
30 Notes:
Support needed for Lever only because of the gear teeth.
I printed with 3 outside layers for strength.
The bottom piece was modified for extra strength as it broke right at the corner in initial testing. -
36 inch 24 inch jaw crusher 2D drawings 3D Model
36 inch 24 inch jaw crusher 2D drawings,Is a complete set of drawings, after downloading can understand the production. This product is produced, no problem. The format is DWG and can be edited.
