3DHunt.co

Tag: CR-10S

  • Creality 3D CR-10S End Cap 3D Print Model

    Creality 3D CR-10S End Cap 3D Print Model

    Summary
    This replaces the end cap on CR-10S and CR-10. I designed this to be able to add custom colored end caps to my CR-10S. This was also designed as proof of concept for a stable mounting point for a camera, sensors or other things that need mounting. I will upload variants of this with an arm to hold a camera or a light securely to the gantry.
    Print Settings
    Printer Brand:
    Creality
    Printer:
    CR-10S
    Rafts:
    Doesn’t Matter
    Supports:
    Doesn’t Matter
    Resolution:
    0.2 mm
    Infill:
    20%
    Notes:
    Print at what ever resolution you wish and infill you wish. The part prints fast and strong. This printed part stood up to repeated insertions and removal.

  • CR-10S Hinged Filament Sensor Mount (Bottom Plug) 3D Print Model

    CR-10S Hinged Filament Sensor Mount (Bottom Plug) 3D Print Model

    Summary
    CR-10S Hinged Filament Sensor Mount (Front Plug)https://www.thingiverse.com/thing:2791872
    CR-10S Hinged Filament Sensor Mount (Bottom Plug)https://www.thingiverse.com/thing:2826099
    Lets be honest. The filament runout sensor is a great addition to the Creality CR-10S, but the factory slide-on mount that Creality supplies sucks. I download and printed several other designs from here and just wasn’t happy with the alignment or functionally of them, so I designed my own.
    I wanted the filament to be feed straight thru with enough room inbetween to manage any kinks or wobbles in the filament with your hands. I also wanted a better way to reduce friction thru it when near Z=0 and Z = 200+ as the filament is drug thru the horizontal position of the sensor first which is dependent on the way you install the roll (over the top or under). Thats when putting a hinge inbetween seemed like the perfect solution as I run a TUSH spool holder with the extruder feed off the bottom of the spool. I designed this Hinged Filament Sensor Mount so it can be bolted onto the Z-axis brass lead screw nut using factory hardware, then the mount is stabilized to the Z column roller mount right at the hinge. I also designed it so you could run the sensor fully enclosed or with the printed cap to keep crud out. You will need (2) M3X20 screws with (2) M3 hex nuts. Hinge is printed in place.
    Please note that after printing you will need to carefully twist the built-in support material off in the same direction as the pivoting hinge. If you use flush cutter on the support material, you may end up splitting the mount in half. The hinge for this design requires a M3 x 30mm LG screw and a M3 Nut as I couldn’t model it assemblied without alot of wasted support material.
    The sensor I designed this around can be purchased here:https://macewen3d.com/products/cr-10-cr-10-s4-and-s5-replacement-endstop-limit-switch
    Which is the same as the factory Creality CR-10S filament runout sensor or Axis stop sensors. My machine actually came with a spare, which made designing/refining it pretty easy.
    Some people didn’t like my previous version of this mount since the plug for the sensor was in front, so I remixed it so the plug is now facing downward.

  • CR-10S Locking Bed Leveling Knob 3D Print Model

    CR-10S Locking Bed Leveling Knob 3D Print Model

    Summary
    Inspired by orcusomega’s “Locking CR10/S4/S5 Bed Leveling Knob” (https://www.thingiverse.com/thing:2462249). This is a knob that you can insert an M4 lock nut into. The hole for the screw is not fully open. After printing there is a .4mm layer that you need to cut with a utility knife before use. No supports are necessary.
    Quote from orcusomega’s notes:
    “Requires a total of 8 M4 nylon locknuts. Remove the stock leveling wheels, and use one of the locknuts to keep the screw in place on the hot bed (being the nut all the way to the top,. making the screw stay in place without the need to hold the top with a screwdriver). Then replace the springs. Insert the remaining M4 locknuts into the wheels and thread them on – wala!”

  • Creality CR-10S Control Box Fan Holder 60mm for NOCTUA NF-A6x25 3D Print Model

    Creality CR-10S Control Box Fan Holder 60mm for NOCTUA NF-A6x25 3D Print Model

    Summary
    Creality CR-10S Control Box Fan Holder 60mm for NOCTUA NF-A6x25
    Remove the right thing of the OEM Fan Holder carefully to install this part.
    Print Settings
    Printer:
    CR-10S Rafts:
    Doesn’t Matter Supports:
    Yes Resolution:
    0.15mm Infill:
    40%