I modeled this in Solidworks and rendered in Keyshot, Basic utility knife with razor and clip to attach to belt.
Tag: Clip
-
of the Push Pin 3D Model
TurboSmooth modifier can be used to increase mesh resolution if necessaryPreview rendered with V-RayFile Formats: 3ds Max 2012, FBXReal-world scale, units – millimetersLighting is not included
-
Model of Binder Clip 3D Model
TurboSmooth modifier can be used to increase mesh resolution if necessaryPreview rendered with V-RayFile Formats: 3ds Max 2012, FBXReal-world scale, units – millimetersLighting is not included
-
of the Paper Clip 3D Model
TurboSmooth modifier can be used to increase mesh resolution if necessaryPreview rendered with V-RayFile Formats: 3ds Max 2012, FBXReal-world scale, units – millimetersLighting is not included
-
Cable clip v2 remix 3D Print Model
Summary
Thanks to JTM 88 for the original. I extended the base to add a second screw hole as it suited me more. Great design.
Print Settings
Printer:
ultibots d300vs
Rafts:
Doesn’t Matter
Supports:
Doesn’t Matter
Resolution:
.2mm
Infill:
50%+ -
JBL clip 3D Print Model
Summary
Is just a simple clip for JBL Go, to use in the car.
Print Settings
Printer:
Monoprice mini
Rafts:
No
Supports:
No
Resolution:
0.2
Infill:
100% -
Electric Saint Helmet Goggle Clip 3D Print Model
Summary
Goggle clip for the Electric Saint helmet. Mine required some filing, but after that it clipped right on. -
Venetial Blind Angle Cord Clip 3D Print Model
Summary
This is a clip that the venetian blind angle adjusting cords connect to. These clips are up in top and slid and clip into place on a ‘D’ shaped rod. When the clips rotate the cord wraps around these clips causing the blinds angle to change.
I printed this on a stock CR-10, horizontally with clip side up.
.1 layer height
100% infill
Support evrywhere
Brim
30 mm/sec
PETG for clip flexibilty
245c Noz
70c Bed
I have included the STL and the SCAD in case you need to modify for your application. -
Honda Odyssey Hood Latch Clip 3D Print Model
Summary
This is a replacement for the breakage-prone hood latch clip of the Honda Odyssey. To remove the old hood latch clip, just use pliers to compress the clip and pull it out. This one should pop in place with a snap and hold the hood latch bar no problem. I printed it in ABS, but PETG should work fine too. I also printed with supports and 100% infill.
Print Settings
Printer Brand:
Wanhao
Printer:
Wanhao Duplicator i3 Plus
Rafts:
No
Supports:
Yes
Resolution:
.2
Infill:
100% -
HTC VIVE – TPCAST CABLE CLIP FRONT 3D Print Model
Summary
I wanted to arrange all front cables used by TPCAST on my vive. Now they are all alligned and do fit perfectedly. Also no further risk of connection lost.
Print Settings
Printer:
Anycubic I3 Mega
Rafts:
No
Supports:
No
Resolution:
0.2
Notes:
PLA, ~ 8 minutes print time -
Valance Clip 3D Print Model
Summary
This is a valance clip I made to replace one we broke adjusting the blinds. -
Kayak Bungee cord clip 3D Print Model
Summary
This is a model similar to the bungee clips (not sure what they are really called, feel free to correct me) that come on my sundolphin kayak.
Included models with and without supports. -
Bag Clip 3D Model
Practical bag clips by upidesign. stylish and simple, you can easily produce it at home if you need it. Designed in three different sizes, with and without support. We recommend using support for more accurate printing.Rafts: NOSupports: YesResolution: .12Infill: 15%3D model format: STLWebsite coming soon! www.upidesign.com
-
RC Body Clip 1/10 Tamiya etc 3D Print Model
Summary
Here’s a redesigned body clip and spacer for Tamiya style RC cars. It’s an alternate design to the little metal clips which is more suitable for printing in plastic.
These little suckers break easily so just print out a stack of them and have plenty of spares on hand. -
Anet A8 LED strip mount under X axis clip on remix 3D Print Model
Summary
This remix was remixed in Tinkercad to remove the screws. Assembly is the same, but instead of using screws, you just snap fit the brackets on. No screws needed!
😀 -
RIGGED Santa Claus Character 3D Model
If you want to watch the santa rig details how workingClick here:https://www.youtube.com/watch?v=3CRHZtG_KVY&t=1sSanta_Claus_Cartoon_CharacterHigh detailed 3D, rigged model of Santa ready for ANIMATED.============================================included FORMAT:- 3DS MAX /2011&2014/ WITH V-Ray materials and studio ligthing setup /*MAX/- 3ds MAX with Scanline materials /*MAX/-*FBX/Multi Format/RIGGED————————————————————————–Native Format : 3ds max 2014 with V-Ray 3.00.00Vray setup scene gamma 2.2 /3 point lighting setup included/============================================Model:Clean topology based on quads.This model is completely UVunwrapped.Model group material and texture have a clear name.============================================Units used centimeters. Character height: 154 cm tall.============================================Clean, polygonal, edge loop, quads based and smoothable /Subdivision ready/ poly geometryOnly : Quads/TrisModel centered at origin.- Unique and meaningful names for all the model parts, materials and textures for an easy identification.============================================Rigged:Rigged with Biped, Face controllers sliderBiped loop Walking animated============================================TEXTURESVraySSS2 (Sub Surface Scattering) for body4096x4096 JPG (14) – body/Nor,Diff,Disp,CV/ -Cloth/Diff-2,Alpha-2/ -Shoes/Diff,Nor,Roug,Height,AO/-Beard&Hair/Disp/4000×4000 JPG (2) – Body/Spec /-Eye/Diff/2048×2048 JPG (7) – Belt/Diff,Nor,Roug,Ref,Alpha,Height,Ior,588×588 Cloth/bump/If you like it Please rate it
-
Santa Claus Character 3D Model
Santa_Claus_Cartoon_CharacterHigh detailed hd 3D model, awesome for your animation.============================================included FORMAT:- 3DS MAX /2014/ WITH V-Ray materials and studio ligthing setup /*MAX/- 3ds MAX with Scanline materials /*MAX/-*FBX/Multi Format/-*OBJ/Multi Format/————————————————————————–Native Format : 3ds max 2014 with V-Ray 3.00.00Vray setup scene gamma 2.2 /3 point lighting setup included/============================================Model:Clean topology based on quads.This model is completely UVunwrapped.Model group material and texture have a clear name.============================================Units used centimeters. Character height: 154 cm tall.============================================Clean, polygonal, edge loop, quads based and smoothable /Subdivision ready/ poly geometryOnly : Quads/TrisModel centered at origin.- Unique and meaningful names for all the model parts, materials and textures for an easy identification.============================================TEXTURESVraySSS2 (Sub Surface Scattering) for body4096x4096 JPG (14) – body/Nor,Diff,Disp,CV/ -Cloth/Diff-2,Alpha-2/ -Shoes/Diff,Nor,Roug,Height,AO/-Beard&Hair/Disp/4000×4000 JPG (2) – Body/Spec /-Eye/Diff/2048×2048 JPG (7) – Belt/Diff,Nor,Roug,Ref,Alpha,Height,Ior,588×588 Cloth/bump/
-
Citroen, Peugeot rear cable sleeve clip 3D Print Model
Summary
This is a replacement clip for my Citroen C4 (2007) Coupe cable sleeve at the boot.
Since there was a problem with the cables (they would brake every now and then and cause shortcuts) removing the cable sometimes results in braking this little piece that is essential to hold the cable sleeve (FYI: my mechanic broke it and had it super glued, so after a while the whole sleeve would come off!).
It’s a replacement part that you cannot find anywhere (or no one would sell it to me!), so I had to print one.
The Citroen order code for this is : 96308075.80.
You will need to print 2 of those since one locks to each other (the locking is not great but a little bit of super glue to each other gets the job done).
Enjoy! 🙂
Print Settings
Printer:
Anet A8
Rafts:
No
Supports:
Yes
Resolution:
0.1
Infill:
100%
Notes:
It’s best to print it in nylon, ABS or PETG. PLA will be too fragile (brakes when sliding in the opening) and since in warm climates the temperature of the roof/ trunk can reach high temperatures I would recommend a much stronger/temperature proof filament.
Use supports if you want it printed as it is (on the side) I have noticed that printing it like this would result in being stronger when bending the flaps. However, if you rotate it you can print it without supports. -
Scorsh Chain easy clip 3D Print Model
Summary
Hi all.
i made that easy chain clip for my cube3 but you can use this everywhere.
Simply make your hole or use double face tape.
Print Settings
Printer Brand:
3D Systems
Printer:
Cube 3
Rafts:
No
Supports:
NoPost-Printing
Scorsh Chain easy clip
just print it. 🙂
How I Designed This
www.tinkercad.com -
Croc fendu (sister clip) 3D Print Model
Summary
Croc fendu pour sécuriser ses accessoires rapidement. -
Golf Ball Belt Clip Remix 3D Print Model
Summary
This is a remix from the TheKre8Group’s one.
Added 3 tee holders, and a slot to label/mark the balls (putting helper).
Printing tips:
o.2 layer height
perimeter width : 0.45
and allow single extrusion wall for the outer perimeters (that’s for the support wall).
All attribution to TheKre8Group! -
Leatherman Rebar Clip Holster 3D Print Model
Summary
I was tired of my leatherman spinning in my pocket so I designed this. It can be clipped inside your pocket or to your belt.
Print Settings
Printer:
Anet A8
Rafts:
Yes
Supports:
Yes
Resolution:
0.1 – 0.2 mm
Infill:
30%
Notes:
May want to use raft or brim to make sure it doesn’t fall over. Use supports below clip but not inside it. -
lock with wire clip for Creality Ender 2 wire chain 3D Print Model
Summary
I remixed the lock of the Ender Cable Chain by ninne (https://www.thingiverse.com/thing:2498801) with the clamp of the bowden wire clips by Evanrude (https://www.thingiverse.com/thing:2328449) to attach the hot bed cable to the chain. It prevents the hot bed calbe from scrubbing the chain and the power cable. -
1/4 inch air hose clip 3D Print Model
Summary
holds air hose to reel, use pop rivits in the holes to attach -
Sunglasses Car Sun Visor Clip – Remix 3D Print Model
Summary
Added a “butée” (french word) to avoid sun glasses fall. -
Clip for AT&T Slimline phone 3D Print Model
Summary
This replaces that little clip that both ensures the phone hangs up and holds it to the wall. It’s easy to break off the little nub that the phone hangs on. -
Mi Drone Stick Cover with Clip 3D Print Model
Summary
English: Mi Drone Stick Cover with Clip
Portuguese: Protetor de Stick (manche) com clip (grampo) de fixação para o MI Drone
Print Settings
Printer:
Anet A8 Rafts:
No Supports:
Yes Resolution:
0.2 Infill:
10 -
Filament roll retaining clip 3D Print Model
Summary
I designed these to hold 1.75mm filament to the edge of the reel to avoid bending the filament as when you use the holes on the edge of the reels. These are designed for the specific brand I use(3D spark) so they may not fit your particular reels. Try the single part first before printing the 12 x nest of parts,
I will also leave a STEP file so people can adjust the gap to fit their needs as they see fit.
I found that using 2 of they per reel worked best.
Print Settings
Printer:
tevo tarantula Rafts:
No Supports:
No Resolution:
0.2mm Infill:
20%
Post-Printing
If the hole is a little small, use a 2mm or 5/64″ drill to clean out the hole. -
Nissan Pathfinder / Xterra / Frontier hood prop rod clip 3D Print Model
Summary
Replacement hood prop rod clip
Fits:
Frontier 2005-2017
Pathfinder 2005-2012
Xterra 2005-2015
I printed mine with small supports under the little clip legs, and it printed fine.
Hope this helps! -
Customizable anti-backlash bowden coupling clip 3D Print Model
Summary
There are many designs like that, the one I picked for source is just the most pretty I used, it’s not that it was of particular value in terms of inspiration. Problem is all these designs are either wrong size or ugly and never customizable so I thought I’d solve that problem once for myself (and share here while I’m at it).
The dimensions of supplied stl is for all e3d couplings I have around, if you have different hardware, feel free to customize.
Note: for some reason customizer refuses to open now, so I can’t tell if it works well, but you can either use prebuilt .stl or download .scad and customize. I’ll check it again later and will either adjust it or remove WIP.
Print Settings
Rafts:
No Supports:
No -
Glass clip monoprice 3D Print Model
Summary
remix shorten the distance between the clips holding the glass and heating bed.
also the heating bed and gantry -
Vent clip cell phone caddy 3D Print Model
Summary
This is an item that I created on Inventor for class.Overview and Background
cell phone holder
This is a holder for a car that attaches to the vent clipl
Lesson Plan and Activity
cell phone holder
I created this for my intro 3d printing class -
Nose Clip 3D Print Model
Summary
Nose clip that i’m going to be using for my next project (Steampunk Gas Mask) that works 😉
!Don’t forget to check out my other designs and Follow my weekly KooKoo uploads, Enjoy 😉
Print Settings
Rafts:
No Supports:
No Resolution:
0.2 Infill:
75% Notes:
3 shells -
Binder clip 3D Model
– Modeled in Blender- Preview image rendered using cycles- Only quads polygons- All scene are included in .blend filesClick on my user name to see my complete galleryHope You like it
-
replacement sterilite container clip 3D Print Model
Summary
I buy lots of these sterilite containers. I imagine a lot of 3D printing hobbyists do. Frequent usage means the clips eventually break. Instead of having to spend another $5 – $12 dollars and throw away a perfectly good container, I drafted a replacement clip.
I know it’s lame, but I use a lot of them and it is wasteful to have to purchase again. The attached image is the container where I keep my coffee. Of course that’s going to break first, using it everyday for over 2 years.
PLA
.3mm Draft
No Support
Hollow / Shell, No Infill
With these basic settings the printed design is stronger than the factory clip. -
Rock Climbing Stick Clip with pole threads 3D Print Model
Summary
This is a remix of https://www.thingiverse.com/thing:870219
I added threads for a painters pole or broom handle. I also combined it into one file so there is no need to glue it together.
Print Settings
Printer Brand:
Wanhao Printer:
Wanhao Duplicator i3 Plus Rafts:
No Supports:
Yes Resolution:
.2mm Infill:
20% -
Browning Hi Power Hand Gun – Game Ready 3D Model
A game ready Browning Hi Power Hand Gun. Made in Blender, rendered with Cycles and tested in Unity game engine.|Game Ready|- Asset has been dropped into and tested in Unity- Easy to re-apply texture in game engine|Mesh Details|- made with polygonal quads only.- low poly and designed for games.|Material/Texture Details|- 2K texture. Can easily be reduced in quality to save space.- PBR material workflow in Blender only. Materials will have to be re-applied in non-native formats|Formats|- Files include BLEND, FBX, OBJ, DAE (Collada)- No plugins used__________________________________________Visit http://xepphire.weebly.com/Enjoy the model! Any questions feel free to email me 🙂
-
Cat Photo Stand Clip 3D Print Model
Summary
A picture stand that clips on monitors or other things. It is made to snugly fit a monitor 7.5-8 mm thick and hold 1 picture.
Print Settings
Printer Brand:
Prusa Printer:
i3 MK2S Rafts:
No Supports:
No Resolution:
.2 Infill:
20% Notes:
Ears and features are printed at different heights to allow for color changes.
Simply super glue the back to the front when finished printing. -
Cooler Master Vortex Plus CPU Cooler Mounting Clip 3D Print Model
Summary
Mounting clips for a Cooler Master Vortex Plus CPU cooler.
I had several of these break on me after moving my computer around, so I grabbed the remaining intact ones and modeled them out.
Print Settings
Printer:
Creality CR-10 Rafts:
No Supports:
Yes Resolution:
0.1 mm Infill:
100% Notes:
Printed with PETG for better temperature resistance.
I found the best orientation for these parts is to place Push Pin (A) horizontally with the long edge of the base triangle against the print bed and Push Pin (B) horizontally with the split tip perpendicular to the print bed and supports only on the parts touching the bed.
This is a small part so there will likely be some variation from print to print (mine came out pretty ugly, but functional).
Post-Printing
The slot at the top of Push Pin (B) needs to be cut to extend it out to edge of the part.
This wasn’t included in order to print more solidly, but it may be able to be printed with supports.
This allows Push Pin (A) to be inserted and rotated into the part.
How I Designed This
Designed in Fusion 360; .f3d file is included. -
Garbage Bag Clip 3D Print Model
Summary
I want to try making a clip for garbage bags, based on a shortened version of a clip to an english muffin package I had laying around. -
Wooden Clothes Pins 3D Model
Traditional wooden pegs with springs. Both objects are efficiently modeled with 100% quad topology, and relatively light polygon count; a total of just 3,368 polygons, and 3,378 vertices. The two clothespins are UV unwrapped, and come complete with detailed diffuse, specular, and bump maps (1024x1024px). I’ve also included base UV Templates for each object, in case you decide to create your own textures. Seamless procedural maps should also work well.
-
72mm lens cap clip for neck strap 3D Print Model
Summary
I designed this for my Sony, but I’d expect it can work with other brands. I didn’t like the others I saw that are round and bulky when no cap is attached so I designed this streamlined version. I holds tenaciously.
To attach to neck strap, pinch a fold and insert it over one of the three tabs. You’ll have to work it a bit and pull from other side as it is designed to be snug. Repeat for other two. -
Fastening clip 3D Print Model
Production of a staple for fixing the vehicle beams
in abs with foot fixing hole diameter 6 mm or without fixing foot. -
Hose clip 9 mm 3D Print Model
Achievements of 2 ABS staples to hold the 9 mm car fuel pipes in gauge and proximities
-
Helping Hand 3D Model
HELPING HAND=================================- Modeled in Blender.- Preview image rendered using cycles.- All scene are included in .blend files.- Poly count are before sub division- Great for close up render.- All parts and materials are logically named.OTHER FORMATS=================- 3ds MAX- COLLADA (.dae)- Autodesk FBX- OBJ
-
Wire Management Clip 3D Print Model
Summary
This is a simple wire clip, made to be stuck down to a table or the wall with some 3M double sided foam tape. Simply cut the tape down to the side of base of the clip (14×14 mm)
I personally use one under my bedside table to hold my USB-C cord, so when I unplug my phone, the cord doesn’t fall onto the floor. I also use one on my wall to hold my micro USB cable for my LG Tones. -
LOXX Belt Clip Connector 3D Print Model
Summary
A strong and safe attachment solution to keep things attached to your person. This belt look design interfaces with LOXX connectors to allow quick connect and disconnect of everyday carry or larger items such as cameras or belt pouches (eg Leatherman sheath)
See more info here: http://www.makealittlemore.com/2017/07/06/experimenting-with-loxx-fasteners/
The connectors can be bought here: http://www.loxx.shop/en/new/loxx-starter-set-nickel/a-676/
They even supply key chains with a hole for the connector pre-made: http://www.loxx.shop/en/neu/loxx-lifestyle-lederpatch-loxx-blau/a-685/
Print Settings
Printer Brand:
Prusa Printer:
Prusa Mk2 Rafts:
No Supports:
No Resolution:
0.15 Infill:
100% Notes:
make it as strong ass possible!! maybe use ABS. -
Money Clip Free 3D Model
Basic, easy to print functional money clip. Enjoy!Print Settings:50mm/s0.1mm or lessFill: 25%No raft or support require
-
Vornado Fan guard clip 3D Print Model
Summary
Vornado fan guard clips. I designed these to hold the fan guard on my Vornado fan in place. Drill a hole through the top and use a short screw. -
DJI Mavic Pro Simple Battery Clip (With Charge Indicators) 3D Print Model
Summary
A slight amendment to my previous design https://www.thingiverse.com/thing:2398749 this version includes a battery icon on the bbase of the aprt. This way you can use one to mark fully charges vs discharged batteries. Makes it easy to tell at a glance which are ready to go and which need charging. I print the charged ones in green and the discharged ones in red!
A very simple little battery clip to cover the fairly exposed battery contacts on the DJI Mavic Pro’s Battery.
The clip is JUST big enough to fit over the contacts and the first time may take some pressure and trial and error to get it to go on, after this it should be a very snug fit.
I keep a few spares in my bag as these are friction fit, eventually they’re going to become loose, so I always have a spare.
I have included the STL and SKP file in case you wish to make any changes, but the design works well for me/my printer. -
Squeeze clip for filament spool spindle / axle 3D Print Model
Summary
For my Anet A8 I wanted a quick release alternative to the supplied M8 nuts, so I designed this squeeze clip. To use just squeeze the arms together slightly to release the grip on the rod and slide off. They won’t grip as well as a nut with lock nut, but it works fine to hold the spindle in place.
I made 2 sizes one for the stock M8 threaded rod with an inside diameter of 7mm and a smaller one for a 6.4mm guide rod I salvaged for a scanner, used for a different spool stand.
Print Settings
Printer:
Anet A8 Rafts:
No Supports:
No Resolution:
0.2mm Notes:
I used a wide skirt to help with bed adhesion, My printer isn’t keen on small parts and I lose accuracy without the skirt. Your printer may vary.
The needed supports are all built in and will snap off. I print the clips with 4 lines on the walls / shells hence the 0% infill. I tried printing with thinner walls and 20% infill, but the clips were prone to snapping.
Post-Printing
Trim any skirt and stringing. The support in the gap between the rings that allows the clip to flex, will break free the first time the clip arms are squeezed.
There may be a small amount of support material that needs freeing up from the gap. I used tweezers and a craft knife.
How I Designed This
Designed with Fusion 360 -
JAL- Treadmill safety key and clothing clip for Proform C42 model PCTL2932.0 3D Print Model
Summary
I recently purchased a used Proform C42 treadmill model PCTL2932.0 which did not come with the safety key needed to run it, so I made this one.
I also made a clip to attach to my clothing while using the treadmill, and connected it to the key via a string. With this, if i fall or otherwise leave the treadmill during use, the safety key will be removed from the treadmill bringing it to a stop. -
C-Clip System 3D Print Model
The C-Clip system allows, when integrated into your design, to assemble and disassemble several parts. The connection can be rotated with 32 positions.
-
Cabinet glass retainer clip – 5/16″ 3D Print Model
Summary
Glass retainer clip used for kitchen cabinets.
Print Settings
Printer Brand:
Ultimaker Printer:
Ultimaker 2 Extended Rafts:
No Supports:
Doesn’t Matter -
Scissors Clip (improved) 3D Print Model
Summary
Just another clip, an improved design
Print Settings
Printer Brand:
Prusa Printer:
Prusa Mk2 Rafts:
Doesn’t Matter Supports:
Yes Infill:
10% Notes:
Print at slower speed and 5mm brim will help to counter warping -
Plate Clip – Parametric 3D Print Model
Summary
I had a couple things artsy things around the house that have just been sitting around on tables collecting dust or worse and I decided to hang them up.
I designed this parametrically in Fusion 360 and i’ve included the Fusion 360 file here so you can make one that fits your needs.
Though it probably doesn’t make much difference… since I’ve designed this for a round flat object, instead of a flat mating surface on the clip it actually takes into account the curvature of the plate when it draws the clip. -
Pencil Clip 3D Print Model
Summary
I designed a pencil clip. This is designed to clip onto your backpack so you can easily clip your pencils onto it. I made it because I am sick and tired of always digging through my backpack for a pencil and it makes it easier for me to reach it.
I created this thing for people who have organizational issues. I frequently find myself without a pencil and can’t keep track of them, so I made this so it is easier for me to keep track of my pencils. This could work for pens also. -
Anycubic Plus bed clip for 240mm bed and glass
Summary
JamesWhite made a great bed mount that surpassed the original 6 mounting blocks that were provided with the Anycubic Linear Plus Kit. My version (03/21/2017) came with a 240mm aluminum heated build platform and 240mm glass plate. I just knocked down the tab a bit with Sketchup so they’d both fit without sitting higher. Admittedly, I don’t have any skills with design or these cad apps, so this is just a tweak.
If one were so inclined, adding a few bulges or tangs to the last 1-1.25mm at the top would likely hold the glass in place without the need for the top clips. I don’t think this would even protrude too far from the edge, just far enough to put a touch of pressure on the glass.
Thanks, JamesWhite.
Print Settings
Printer:
Anycubic Linear Plus Rafts:
Doesn’t Matter Supports:
No Resolution:
.2-.4 Infill:
30% Notes:
You could probably up the infill a hair, but this seems strong enough. I just printed it and did a test fit before I printed the rest. Should work well for my needs. -
Scissors 3D Model
The model can be used to visualize repair shops, in the industrial sector.
**************************************
Originally modelled in SolidWorks2016.
Final images rendered with 3ds Max 2016 + V-Ray.
**************************************
Model:
5 objects,2 materials (VRay standard materials)
Geometry: Polygonal Quads
**************************************
**************************************
File formats:
– 3ds Max 2013 with V-Ray material;
– 3ds Max 2016 with V-Ray material;
– obj- no textures;
– Solidworks 2016;
-and other formats
Every model has been checked with the appropriate software.
**************************************
Also check out my other models, just click on my user name to see complete gallery -
MakerBot Replicator – Tensioning Belt Clip
Summary
Clip that connects the belt ends broke a clip…. Created this replacement while the new one shipped to me…
I just used basic print settings
